• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2006.11a
• /
• pp.373-376
• /
• 2006

In general, a method for generating irregular wave by combination of component waves obtained from linear wave theory is widely used. In these method, however, mean water surface elevation is rising from time to time because of nonlinear effect of wave. In this study, for the rising problem of mean water surface elevation and stabilization of calculation from time to time, mass transport velocity for horizontal velocity at wave source position is considered. The rising problem of mean water surface elevation is checked by comparing calculated wave profile from numerical technique proposed in this study with target wave profile at wave source position in numerical wave tank by using CADMAS-SURF code. And, by generating irregular wave, the validity of wave overtopping rate estimated from this numerical analysis is discussed by comparing computed results with measured results in hydraulic model experiments for vertical seawall located on a sloping sea bottom. As a results, the computations are validated against the previously experimental results by hydraulic model test and numerical results of this study and a good agreement is observed. Therefore, numerical technique of this study is a powerful tool for estimating wave overtopping rate over the crest of coastal structure.

• Journal of Ocean Engineering and Technology
• /
• v.28 no.1
• /
• pp.6-11
• /
• 2014

This paper presents the results of an experimental study of wave run-ups on a semi-submersible offshore structure. A series of model tests with a 1:80 scale ratio were carried out in the two-dimensional wave basin of MOERI/KIOST. The experimental model had two columns and one pontoon. The model was fixed and wave elevations were measured at five points per column. Two different draft (operational & survival) conditions and three wave heights were considered under regular wave conditions. First, the nonlinear characteristics of wave run-ups are discussed by using the time series data. Then, the wave heights are compared with numerical results based on the potential flow model. The comparison shows fairly good correlation between the experiments and computations. Finally, wave run-ups under the operational and survival conditions are suggested.

• Ocean Systems Engineering
• /
• v.4 no.3
• /
• pp.169-183
• /
• 2014

For the reliable design of substructure supporting offshore wind turbines it is very important to reduce the effects of wave forces. Since the substructure is strongly influenced by the effects of wave forces as the size of substructure increases. In the present study, the hybrid substructure with multi-cylinder is newly suggested to reduce the effects of wave forces. Using diffraction theory the scattering waves in a fluid region are expressed by an Eigenfunction expansion method with three dimensional potential theory to calculate the wave force acting on the hybrid substructure. The wave force and wave run-up acting on the hybrid substructure is presented to examine the water wave interaction according to the variation of cylindrical size and the distance among cylinders. It is found that the suggested hybrid substructure with multi-cylinder is very useful to reduce the effects of wave forces acting on the substructure for offshore wind turbines.

• Journal of the Society of Naval Architects of Korea
• /
• v.58 no.2
• /
• pp.112-120
• /
• 2021

The novel wave generating system of a wave flume has been devised by utilizing the analytic solution of wave board motion in idealized two dimensional space. The arbitrary oscillation motion of submerged wave board segment has been defined by sinusoidal motion of upper and lower end of the wave board. The analytic solution of the wave board motion has been represented by the solution of board motion due to flap motion and swing motion. Arbitrary oscillation of the board could be specified by determining amplitude, frequency, and the phase lag. A novel hybrid wave generator could be operated not only in piston motion but also in flap or swing motion by selection of control parameter. The wave generator has unique motion enhancing ability by appending flap motion or swing motion to piston motion in wave generation. In addition the hybrid wave generator has advantages in generating high quality wave spectrum of irregular wave in simulating real sea condition.

• Journal of Biosystems Engineering
• /
• v.33 no.4
• /
• pp.282-287
• /
• 2008

Love wave is one of the shear horizontal waves and it can propagate between two layers in liquid without energy loss. The SAW (surface acoustic wave) sensor using Love wave is very useful for real time measurement of the viscosity of liquid with high sensitivity. In this study, the 77 MHz and 155 MHz Love wave SAW sensors were fabricated and use to measure the viscosity of low viscous liquid. To generate the surface acoustic wave, the inter-digital transducers were fabricated on the quartz crystal wafer. In order to obtain the optimal thickness of the coating film (novolac photoresist) generating the Love wave on the surface of SAW device, theoretical calculation was performed. The performances of fabricated Love wave SAW sensors were tested. As test liquid, pure water and glycerol solutions having different concentrations were used. Since the determination coefficients of the regression equations for measuring the viscosity of liquid are greater than 0.98, the developed Love wave SAW sensors in this study will be very useful for precise measurement of viscosity of liquid.

• Journal of Korea Water Resources Association
• /
• v.46 no.5
• /
• pp.491-504
• /
• 2013

In this study, wave breakings over a shelf region are investigated under irregular wave conditions through laboratory experiments in a wave flume. Numerical simulations based on the Boussinesq-type equations are also conducted. The characteristics of breaking waves such as significant wave height, crest and trough heights, the mean water level and the stable wave height are obtained by analyzing laboratory measurements in detail. Obtained results are compared with those of the Boussinesq-type equations model. A very reasonable agreements is observed. The broken waves over a horizontal bottom asymptotically approach a stable wave height($H_{stable}$). In this study, the relative stable wave height is found as $H_{stable}/h{\fallingdotseq}0.56$ for irregular wave.

• Journal of the Society of Naval Architects of Korea
• /
• v.60 no.2
• /
• pp.76-85
• /
• 2023

The present study aims to review the wave pattern resistance analysis method suggested by the International Towing Tank Conference. From the experimental database of a container carrier ship model, the wave pattern measurement and resistance test results are utilized. The wave pattern resistance at the design Froude number is obtained to be compared with the wave making resistance of experiments. Wave pattern resistance is lower than wave making resistance by 1978 ITTC and uniform regardless of transverse location of wave cut. The method is also applied to the wave height field by Computational Fluid Dynamics (CFD) analyses with Froude number variation. Although numerical damping suppressed waves in downstream, waves around the hull and wave pattern resistance are properly predicted.

• Water for future
• /
• v.7 no.2
• /
• pp.99-106
• /
• 1974

The records of wave heights which were observed at Muk ho and Po hang of the East Coast of Korea were analized by several probility functions. The exponential 2 parameter distribution was found as the best fit probability function to the historical distribution of wave heights by the test of goodness of fit. But log-normal 2 parameter and log-extremal type A distributions were also fit to the historical distribution, especially in the Smirnov-Kolmogorov test. Therefore, it can't be always regarded that those two distributions are not fit to the wave heiht's distribution. In the test of goodness of fit, the Chi-Square test gave very sensitive results and Smirnov-Kolmogorov test, which is a distribution free and non-parametric test, gave more inclusive results. At the next stage, the inter-relationship between the mean and the one-third wave heights, the mean and the one-=tenth wave heights, the one-third and the one-tenth wave heights, the one-third and the highest wave heights were obtained and discussed.

• Journal of Ocean Engineering and Technology
• /
• v.19 no.4 s.65
• /
• pp.9-14
• /
• 2005

In the present paper, the wave absorbing performance of the fully submerged horizontal porous plates has been investigated, numerically and experimentally. The submerged porous system is composed of multi-layered horizontal porous plates that are clamped at the vertical setwall, which are slightly inclined and placed vertically, in parallel, with spacing. The hydrodynamic interaction of incident waves with the rigid porous multi-layered plates was formulated within the context of linear wave-body interaction theory and Darcy's law. In order to validate the effectiveness of the present computing code, the numerical results were compared with the analytical and experimental results. It is found that triple horizontal porous plates with slight inclination, if properly tuned for wave energy dissipation against the standing waves in front of the vertical wall, can have high performances in reducing the reflected wave amplitudes against the incident waves over a wide range of wave frequency.

• Journal of Ocean Engineering and Technology
• /
• v.23 no.1
• /
• pp.43-47
• /
• 2009

This paper compares theoretical wave profile and particle kinematics with experimental results generated by a 2 D wave tank. Particle velocity fields of compound waves were acquired using a PIV technique. Synchronization was applied to acquire images of the wave fields, and the time gap between these images was controlled by the user. This technique was applied to investigate the wave breaking mechanism, and the wave profile and velocity distribution in a wave breaking field was obtained.