• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.15-19
• /
• 2006

GPS has been increasingly exploited to provide positioning and navigation solutions for a variety of applications. In vessel berthing application, however, there are stringent requirements in terms of positioning accuracy, availability and integrity that cannot be satisfied by GPS alone. This is because the performance of satellite-based positioning and navigation systems are heavily dependent on both the number and the geometric distribution of satellite tracked by receivers. Due to the limited number of GPS satellites, a sufficient number of ‘visible’ satellites cannot be sometimes guaranteed. This paper discusses some issues associated with the implementation of ground-based pseudolite augmentation for vessel berthing. Pseudolite means small transmitter that transmits GPS-like signals in local area. Actually, pseudolite can play three different roles in GPS augmentation scheme, depending on the operational conditions. Firstly, in the case of kinematic GPS operation where there are no signal blockages, and more than five satellites are available, additional pseudolites strengthen the GPS satellite-pseudolite geometry, and more accurate and reliable positioning solution can be achieved. Secondly, in the case when there are adverse GPS operational environments in which the number of tracked satellites is less than four, pseudolites can complement the GPS signals. In the third case, GPS signals are completely unavailable, such as when operated indoor. In such cases the pseudolites can replace the satellite constellation. However, the first role will be considered in this paper, since more than four satellite signals can usually be tracked in most marine applications. This paper presents that the pseudolite-augmented precise positioning system can provides continuous centimeter-level positioning accuracy through comparison analysis of RDOP simulation result of the GPS satellite constellation and the pseudolite-augmented GPS satellite constellation.

• Korean Journal of Geomatics
• /
• v.2 no.1
• /
• pp.57-64
• /
• 2002

Measuring the depth of water is very important in ensuring the protection and safety of seaside. There are many difficulties in making the contour bathymetric map, and contour line due to the limitation of continuous measurement of water depth and collimation with the conventional measuring and positioning methods. But the real-time kinematic GPS (RTK GPS) positioning using a carrier phase enables us to decide a precise position without breaking a signal even under the condition of a moving environment. It is also possible to obtain an accurate depth of water in real time with a fathometer through the measuring of time delay between sending and receiving epochs. This research aims at investigation of accuracy potential of RTK GPS in combination with Echo Sounder(E/S) for the coastal mapping. Apart from this purpose, the accuracy of ambiguity resolution with the OTF(On the Fly) method was tested with respect to the initialization time. The result shows that the accuracy is better than 1cm with 5-minute initialization in the distance of 10km baseline. The seaside topography was measured by the RTK GPS only, on the other hand the seafloor topography was surveyed in combination of RTK GPS and E/S. Comparing to the volume of seaside measured by RTK GPS and digital topographical map, the difference of only 2 % was achieved. This indicates that the coastal mapping with RTK GPS is successfully conducted. In addition it is also demonstrated that the 3-dimensional perspective model resulted from the undersea topography measured by RTK GPS and E/S is very close to that from the digital map. Through this study, it was verified that RTK GPS is to be very useful method in the analysis of coastal morphology owing to its capability of getting the precise DTM for the using of harbor reclamation, dredging, and the estimation of soil movement in a river.

• Journal of the Korea Society of Computer and Information
• /
• v.29 no.8
• /
• pp.11-21
• /
• 2024

This study explores the use of virtual reality (VR) technology to identify and label key segments of the golf swing. To address the limitations of existing VR devices, we developed a platform to collect kinematic data from various VR devices using the OpenVR SDK (Software Development Kit) and SteamVR, and developed a semi-automated labeling technique to identify and label temporal changes in kinematic behavior through LSTM (Long Short-Term Memory)-based time series data analysis. The experiment consisted of 80 participants, 20 from each of the following age groups: teenage, young-adult, middle-aged, and elderly, collecting data from five swings each to build a total of 400 kinematic datasets. The proposed technique achieved consistently high accuracy (≥0.94) and F1 Score (≥0.95) across all age groups for the seven main phases of the golf swing. This work aims to lay the groundwork for segmenting exercise data and precisely assessing athletic performance on a segment-by-segment basis, thereby providing personalized feedback to individual users during future education and training.

• Journal of Navigation and Port Research
• /
• v.36 no.6
• /
• pp.437-442
• /
• 2012

As of 2012, for service-area-widening and commercialization of DGPS service, the Ministry of Land, Transport and Maritime Affairs has completed a DGPS service via Terrestrial Digital Multimedia Broadcasting and doing experimental broadcasting. In this study, kinematic positioning tests were conducted based on DGPS service via T-DMB using low-cost GPS equipments in a dynamic environment. Standalone GPS, single-reference NDGPS via NTRIP, and virtual-reference DGPS via T-DMB surveys were conducted at the same time. And horizontal positioning errors were computed by comparing them with the result of high-precision positioning. As a result, when the DMB transmission interval was 3 seconds, horizontal positioning errors of standalone GPS, NTRIP-DGPS, and DMB-DGPS were 2.3m, 1.0m, and 0.7m, respectively. When the interval was 1 second, horizontal positioning errors were 2.0m, 1.2m, and 0.8m, respectively. Thus horizontal positioning accuracies improved with the DMB-DGPS compared to the traditional single-reference NDGPS.

• Journal of Korean Society for Geospatial Information Science
• /
• v.23 no.3
• /
• pp.31-39
• /
• 2015

This paper presents the static and kinematic positioning accuracy by the real-time GPS positioning modes of the low-cost GPS receivers using NTRIP-based augmentation service. For this, acquires both the raw measurements data of the field tests by LEA 6T GPS module of u-blox AG, and correction communication via NTRIP caster with RTKLIB as an open source program for GNSS solution. With computing the positions of the check points and road tracks by six kinds of GPS positioning modes which are Single, SBAS, DGPS, PPP, RTK, and TCP/IP_RTK, compared these results to the reference position of the check points. The position error average and rmse of the static test by GPS L1 RTK surveying showed $N=0.002m{\pm}0.001m$, $E=0.004m{\pm}0.001m$ in horizontal plane, and $h=-0.116m{\pm}0.003m$ in vertical, these results are very closed to the coordinates with the geodetic receiver. Especially, in case of the kinematic test with obstacles located on both sides of road, the computed track with ambiguity fixing showed very similar trajectory considerably from VRS network RTK mode. And also, evaluate and verify the performance of the TCP/IP_RTK mode developed based on TCP/IP protocol.

• Journal of Korean Society for Geospatial Information Science
• /
• v.24 no.3
• /
• pp.11-18
• /
• 2016

Since GNSS signals get blocked by buildings in urban canyons or narrow alleys, it is very difficult to secure a enough number of visible satellites for satellite navigation in those poor signal-reception environments. In those situations, one cannot get their coordinates or obtain accurate positions. In this study, a couple of strategies for improving positioning accuracy in urban canyons were developed and their performance was verified. First of all, we combined GPS and GLONASS measurements together and devised algorithms to quality-control observed signals and eliminate outliers. Also, a new multipath reduction scheme was applied to minimize its effect by utilizing SNR values of the observed signals. For performance verification of the developed technique, a narrow alley of 10m width located near the back gate of the Inha University was selected as the test-bed, and then we conducted static and kinematic positioning at four pre-surveyed points. We found that our new algorithms produced an 45% improvement in an open-sky environment compared with the positioning result of a low-cost u-blox receiver. In the alleys, 3-D accuracy improved by an average of 37%. In the case of kinematic positioning, especially, biases showing up in regular receivers got eliminated significantly through our new filtering algorithms.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.38 no.6
• /
• pp.521-531
• /
• 2020

QZSS (Quasi-Zenith Satellite System) provides the CLAS (Centimeter Level Augmentation Service) through the satellite's L6 band. CLAS provides correction messages called C-SSR (Compact - State Space Representation) for GPS (Global Positioning System), Galileo and QZSS. In this study, CLAS messages were received by using the AsteRx4 of Septentrio which is a GPS receiver capable of receiving L6 bands, and the messages were decoded to acquire C-SSR. In addition, Multi-GNSS (Global Navigation Satellite System) Code-PPP (Precise Point Positioning) was developed to compensate for GNSS errors by using C-SSR to pseudo-range measurements of GPS, Galileo and QZSS. And non-linear least squares estimation was used to estimate the three-dimensional position of the receiver and the receiver time errors of the GNSS constellations. To evaluate the accuracy of the algorithms developed, static positioning was performed on TSK2 (Tsukuba), one of the IGS (International GNSS Service) sites, and kinematic positioning was performed while driving around the Ina River in Kawanishi. As a result, for the static positioning, the mean RMSE (Root Mean Square Error) for all data sets was 0.35 m in the horizontal direction ad 0.57 m in the vertical direction. And for the kinematic positioning, the accuracy was approximately 0.82 m in horizontal direction and 3.56 m in vertical direction compared o the RTK-FIX values of VRS.

• Journal of Korean Society for Geospatial Information Science
• /
• v.22 no.3
• /
• pp.39-46
• /
• 2014

Network RTK positioning, one of GNSS positioning systems, is currently very popular due to its easy operation and low cost. However, the network RTK positioning unquestioningly accepts observation result acquired with an ambiguity fixed-solution regardless of different field conditions and situations, and then it is applied to the practice. This paper, therefore, has investigated the effects of field conditions obtained network RTK survey data for the area with obstacles on the variation of positioning accuracy. Being explained in detail, after conducting survey by GPS-only positioning and combined GPS/GLONASS observations giving changes to the distance from obstacles and elevation angles, and then accuracy results of each positioning method were compared each other. As a result, while GPS-only point positioning method showed more stable results than combined GPS/GLONASS method in the areas with no obstacles, combined method gave better result than GPS-only for the areas with presence of obstacles. Based on the results of this experiment, when the further study is conducted with a variety of different field conditions affecting the survey accuracy, it can be expected that the accuracy of network RTK survey method would become to more popular.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.1
• /
• pp.31-37
• /
• 2011

Recently gantry-type robot with 3 axes rectangular coordinates have been studied in the many industrial production equipment and machinery fields. To acquire a good handling and motion performance of this robot, reducing the settling-time and securing the accurate-transfer positioning under high-speed conditions should be required. However when robot is moved in high-speed, the large inertia of robot can lead to serious vibration of robot's head. The time-delayed control characteristics of this robot can also lead to tracking error. In this research, the analysis of the effects of higher order positional-profile is carried out to assure high-speed performance and stiffness specifications. To remove the residual vibration caused by kinematic coupling effect of dual-servo gantry, we develop a dual-servo gantry of rotary type that moving frame of x-axis rotates about z-axis. In order to decrease the tracking error, the 3 type lead-filter through system identification was applied respectively. From the experimental results, it was shown that zero-order series leader-filter has the best performance about tracking error and settling time.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.26 no.4
• /
• pp.27-34
• /
• 1989

A potential-based panel method is formulated for the analysis of a partially cavitating 2-dimensional hydrofoil. The method employs dipoles and sources distributed on the foil surface to represent the lifting and cavity problems, respectively. The kinematic boundry condition on the wetted portion of the foil surface is satisfied by requiring that the total potential vanish in the inner flow region of the foil. The dynamic boundary condition on the cavity surface is satisfied by requiring that the potential vary linearly, i.e., the velocity be constant. Green's theorem then results in a potential-based boundary value problem rather than a usual velocity-based formulation. With the singularities distributed on the exact hydrofoil surface, the pressure distributions are predicted with more improved accuracy than the zero-thickness hydrofoil theory, especially near the leading edge. The theory then predicts the cavity shape and cavitation number for an assumed cavity length. To improve the accuracy, the sources and dipoles on the cavity surface are moved to the newly computed cavity surface, where the boundary conditions are satisfied again. It was found that five iterations are necessary to obtain converged values, while only two iterations are sufficient for engineering purpose.