• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.05a
• /
• pp.499-501
• /
• 2011

The phase noise spectrum distribution of COMS Communication transponder was measured and analyzed in the view point of transmission scheme. The effects of phase noise are also analyzed according to the transmission methods. The phase noise of COMS communication transponder may be increased because of utilization of ka-band. So the effects of phase noise will be increased in conditions of high-order transmission mode. The phase noise characteritics are measured for COMS communication transponder with MSM function and the effects for phase noise are analyzed in this paper.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.6
• /
• pp.756-759
• /
• 2012

This paper presents the multibeam service coverage of GEO(Geostationary Orbit) satellite and the practical antenna scheme scenarios to provide the universal communication services on the Korean peninsula. The proposed antenna systems consist of the simplest scheme and feed network so that they can be mounted on satellites. The feed networks are effectively organized according to the frequency and polarization plan. Despite simple structure, all scenarios meet the electrical performance by the optimization of feed allocation and feed excitation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.3
• /
• pp.345-351
• /
• 2000

In this paper, we design and analyze a Ka-band microstrip line to rectangular waveguide transition using the expanding-cell FDTD method. The transition under investigation consists of a ridged waveguide, microstrip line, and $\lambda$/4 Chebyshev impedance transformer. To improve the accuracyand efficiency, the expanding-cell FDTD method is applied to analyze the characteristics of a ridged waveguide impedance transformer. To verify the accuracy of the expanding-cell FDTD method, S parameters of the analyzed transition are compared with those of experimental data. The efficiency of the present approach is verified by comparing the computational time for expanding-cell and that for fine cell. The relation between the number of step and operation bandwidth is analyzed by comparing the characteristics of four and three step Chebyshev waveguide impedance transformer.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.8
• /
• pp.826-831
• /
• 2008

This paper presents hybrid antenna(HA) design based on shaped reflector for mobile satellite communication. HA is composed of a shaped reflector and a feeder having $1{\times}8$ linear phased array, and reflector shaping method is applied for the performance optimization with minimum aperture size. And, in the feeder design, HA has another merit to minimize the manufacturing cost by optimizing the number of element. Proposed HA is designed at Ka-band and can electrically control a beam pattern within ${\pm}3^{\circ}$ in the basic angle of $+45^{\circ}$ in elevation. This antenna is designed to meet ITU-R S.465-5 for beam pattern including side-lobe level.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.3
• /
• pp.279-288
• /
• 2011

This paper will discuss the alignment techniques and measurement results of geostationary satellite communication antennas for correct antenna pointing and also the fixtures. To get the best performance in terms of antenna pointing and fixtures, zero G condition have been simulated and laser tracker and theodolite system have been applied. As a result, alignment stability was verified within the tolerance, ${\pm}\;0.25mm$ and ${\pm}\;0.013^{\circ}$ and finally Ka-band deployable antenna alignment has been accomplished within the tolerance, ${\pm}\;0.5mm$ and ${\pm}\;0.015^{\circ}$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.131-136
• /
• 2008

Two Ka-band 3-stage power amplifiers were designed and fabricated using $0.18-{\mu}m$ CMOS technology. For low loss matching networks for the amplifiers, two substrate-shielded transmission line structures, having good modeling accuracy up to 40 GHz were used. The measured insertion loss of substrate-shielded microstrip-line (MSL) was 0.5 dB/mm at 27 GHz. A 3-stage CMOS amplifier using substrate-shielded MSL achieved a 14.7-dB small-signal gain and a 14.5-dBm output power at 27 GHz in a compact chip area of 0.83$mm^2$. The measured insertion loss of substrate-shielded coplanar waveguide (CPW) was 1.0 dB/mm at 27 GHz. A 3-stage amplifier using substrate-shielded CPW achieved a 12-dB small-signal gai and a 12.5-dBm output power at 26.5 GHz. This results shows a potential of CMOS technology for low cost short-range wireless communication components and system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.12
• /
• pp.1292-1299
• /
• 2003

In this paper, we fabricated new GaAs-based dielectric-supported air gapped microstriplines(DAMLs) using the surface MEMS and the LPF for Ka-band using the fabricated DAMLs. We elevated the signal lines from the substrate, in order to reduce the substrate dielectric loss and obtain low losses at millimeter-wave frequency band with wide impedance range. We fabricated LPF with DAMLs for Ka-band. Due to reducing the dielectric loss of DAMLs, the insertion loss of LPF can be reduced. Miniature is essential to integrate LPF with active devices, so that we fabricated LPF with the slot on the ground to reduce the size of the LPF. We compared a characteristic to LPF with the slot and LPF without the slot.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.17 no.4
• /
• pp.485-491
• /
• 2014

An Antenna & RF system for a fly-away satcom terminal application on ka-band is presented in this paper. The Fly-away satellite terminal can be moved and operated by two person and adapt automatic satellite tracking system in order to decrease the tracking time. Additionally, for low-power consumption, compact size and light-weight, a dual reflector antenna is constructed using dual-offset gregorian antenna structure. For minimize weight, the reflector of the antenna is made of Magnesium. For low-power consumption and light-weight, the pHEMT MMIC compound devices is utilized. The Electronic Band-Gap(EBG) Low-Pass Filter(LPF) is designed for harmonic rejection. In the receiving part, Low-Noise Block converter(LNB) structure is designed for compact and lightweight. In this paper, fly-away satcom terminal with low-power consumption, compact size and light-weight is described with antenna system and RF system performances. Through the experimentation, fly-away terminal's EIRP is more than 50dBW, G/T is more than $17dB/^{\circ}K$.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.5
• /
• pp.19-26
• /
• 2021

This report proposes a waveguide spatial combiner with high power low loss. The proposed spatial combiner implements high power by combining from the center of each port through a waveguide. In particular, we implement low loss using TE01 mode, which has the lowest transmission track loss among modes of circular waveguide, and miniaturization is achieved by applying a new mode conversion method. IIn addition, it was confirmed that it was suitable for high output by calculating the insulation breakdown voltage of the new mode conversion structure through E-field analysis. The final 8-way waveguide spatial combiner was designed and manufactured, and the insertion loss was less than 0.4dB and the combining efficiency was 97% or more, confirming that the electrical performance was very good compared to the planar combining method.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.2
• /
• pp.35-42
• /
• 2022

In this paper, a method to increase the combining efficiency and isolation of the combiner, the core module of SSPA (solid state amplifier), was studied. Specifically, the isolation was secured by matching the common port and the isolation port in the waveguide combiner. The matching structure for matching is in the form of a circular disk and is engraved inside the waveguide combiner. The structure is very simple, so it is possible to secure stable performance. And this structure showed more than 60 times higher critical power performance compared to previous studies, confirming that it is suitable for high output. And by combining 1-stage T-junction and 2, 3 stage MagicT combiner, miniaturization was achieved and the combining efficiency was optimized by reducing the insertion loss. The fabricated waveguide coupler obtained an isolation of 16dB or more and a coupling efficiency of 86.2%.