• Journal of the Korean Solar Energy Society
• /
• v.29 no.1
• /
• pp.58-63
• /
• 2009

In this paper, the power loss due to PV module mismatch in PV string is analyzed and a mismatch compensation method is proposed to improve the efficiency of PV system. The analysis of mismatch loss using PV model simulation reveals that the mismatch module may decrease the total efficiency because the MPPT function of power conditioner make the PV system operate at the local maximum point. The mismatch loss can be severe if the maximum power point current of mismatch module is less than that of string. The proposed compensation method which is simply implemented with a buck type converter shows the possibility to remove the mismatch loss. The effectiveness of the analysis and compensation method is verified by a prototype experiment.

• Journal of electromagnetic engineering and science
• /
• v.10 no.1
• /
• pp.25-27
• /
• 2010

This paper presents a gain and phase mismatch calibration technique for an image-reject RF receiver. The gain mismatch is calibrated by directly measuring the output signal amplitudes of two signal paths. The phase mismatch is calibrated by measuring the output amplitude of the final IF output at the image band. The calibration of the gain and phase mismatch is performed at power-up, and the normal operation of the RF receiver does not interfere with the mismatch calibration circuit. To verify the proposed technique, a 2.4-GHz Weaver image-reject receiver with the gain and phase mismatch calibration circuit is implemented in a 0.18-${\mu}m$ CMOS technology. The overall receiver achieves a voltage gain of 45 dB and a noise figure of 4.8 dB. The image rejection ratio(IRR) is improved from 31 dB to 59.76 dB even with 1 dB and $5^{\circ}$ mismatch in gain and phase, respectively.

• Proceedings of the KIPE Conference
• /
• 2010.07a
• /
• pp.170-171
• /
• 2010

The power loss due to PV module mismatch in PV array system is analyzed and a mismatch compensation method is proposed. A dc-dc converter is used to compensate for series mismatch caused by a low current module in a string. The converter is controlled to maximize the array power output. The proposed compensation method was verified by PSpice simulation.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1939_1941
• /
• 2009

The modulation quality of the RF transmitter in a wireless communication system usually affects system performance and it mostly depends on both a nonlinearity and a distortion, from the intermodulation products and the I/Q mismatch such as I/Q amplitude error and a local phase error, respectively. This paper focused on how much the error vector magnitude(EVM) which describes the modulation accuracy changes according to the variation of the I/Q mismatch components at I/Q modulator. For this work, the equation for the EVM including the I/Q mismatch components can be induced and calculated in accordance with the variation of the I/Q mismatch components. Consequently, the effect of I/Q mismatch components on the EVM, which is required in the transmitter specification of Personal Area Network, can be clearly analyzed.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.2
• /
• pp.35-43
• /
• 2011

In this paper, an analysis on I/Q mismatch characteristics of a quadrature LC VCO(Voltage controlled oscillator) is presented. Based on this analysis, a new I/Q mismatch compensator is proposed. The proposed I/Q mismatch compensator utilizes an amplitude mismatch detector rather than the conventional phase mismatch detector requiring much more wide frequency bandwidth. To verify the proposed circuit, a 2.5GHz quadrature LC VCO was designed in a $0.18{\mu}m$ CMOS process and tested. Test results show that an amplitude mismatch detector achieves similar I/Q mismatch compensation performance as that of the conventional phase mismatch detector. The I/Q mismatch compensator consumes 0.4mA from 1.8V supply voltage and occupies $0.04mm^2$.

• Proceedings of the KIPE Conference
• /
• 2009.11a
• /
• pp.123-125
• /
• 2009

Mismatch of electrical characteristics of modules in PV string invokes mismatch power loss. The mismatch occurs due to various causes such as shadow, aging, contamination, and module exchange. The concept of mismatch compensation converter(MCC) is presented in this paper to remedy the mismatch loss problem. MCC is connected to irregular modules only. MCC is composed of dc-dc converter and MPPT controller. It is noted that MPPT algorithm is employed to control MCC and is effective for maximum power available from irregular modules. The selection guide of MPPT control period is given based on the period of MPPT in PCU. The effectiveness of the MCC is verified by a prototype experiment.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.472-473
• /
• 2008

This paper presents a charge pump used in frequency synthesizer for PHS application. The up/down current mismatch of charge pump has a critical effect on the phase noise and spur performance in frequency synthesizer. Therefore, the mismatch compensation scheme is proposed in this paper. And, the measurement results show that the mismatch can be reduced below 5 %.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.3
• /
• pp.387-400
• /
• 2017

A new junction-splitting based SAR ADC with a redundant searching capacitor array structure in $0.13{\mu}m$ CMOS process to alleviate capacitor mismatch effects, is presented. The normalized average power has a factor of 0.35 to the conventional SAR ADC at 10-bit conversion accuracy. Statistical experiments show the number of missing codes resulting from the mismatch reduces by 95% for 3% unit-capacitor mismatch ratio, while keeping the conversion energy to that of the conventional JS capacitor array.

• Journal of Gastric Cancer
• /
• v.15 no.3
• /
• pp.201-208
• /
• 2015

Purpose: The AT-rich interactive domain 1A (ARID1A ) gene encodes BRG1-associated factor 250a, a component of the SWItch/Sucrose NonFermentable chromatin remodeling complex, which is considered a tumor suppressor in many tumors. We aimed to investigate the prognostic significance of ARID1A expression in gastric cancers and explore its relationship with clinicopathologic parameters such as mismatch repair protein expression. Materials and Methods: Four tissue microarrays were constructed from 191 resected specimens obtained at Soonchunhyang University Cheonan Hospital from 2006 to 2008. Nuclear expression of ARID1A was semiquantitatively assessed and binarized into retained and lost expression. Results: Loss of ARID1A expression was observed in 62 cases (32.5%). This was associated with more frequent vascular invasion (P=0.019) and location in the upper third of the stomach (P=0.001), and trended toward more poorly differentiated subtypes (P=0.054). ARID1A loss was significantly associated with the mismatch repair-deficient phenotype (P=0.003). ARID1A loss showed a statistically significant correlation with loss of MLH1 (P=0.001) but not MSH2 expression (P=1.000). Kaplan-Meier survival analysis showed no statistically significant difference in overall survival; however, patients with retained ARID1A expression tended to have better overall survival than those with loss of ARID1A expression (P=0.053). In both mismatch repair-deficient and mismatch repair-proficient groups, survival analysis showed no differences related to ARID1A expression status. Conclusions: Our results demonstrated that loss of ARID1A expression is closely associated with the mismatch repair-deficient phenotype, especially in sporadic microsatellite instability-high gastric cancers.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.3
• /
• pp.17-22
• /
• 2011

Techniques for mismatch loss minimization to increase the PV system efficiency are under development recently. In this paper, a method to make diagnosis of PV module mismatch is presented, which uses a concept of operating point factor. The method is based on the fact that the ratio of the incremental conductance of a PV module to instantaneous conductance is 1 when the module is operating at its maximum power point. The variations of module voltage and current are taking place by the maximum power point tracker in the power conditioning units of PV system. The effectiveness of the method is verified through an application to a real PV system.