• Journal of the Korean Solar Energy Society
• /
• v.36 no.3
• /
• pp.25-31
• /
• 2016

Gaskets are usually used for the sealing of flange joints. The joint is usually composed of two flanges, a ring gasket and clamping bolts. The metal ring gasket is suitable for pipe flanges, pumps and valve joints in high temperature and high pressure environments. A very high surface stress is developed between a ring type joint gasket and the flange groove when the ring type joint is bolted up in a flange. The dimensions of flanges and ring joint gaskets for the pipe sizes that are in common use are specified in the ANSI codes. However, sometimes it is necessary to make a new design for the flange joint which is not specified in the codes, as the equipment is getting larger and larger in size. This paper presents the contact behavior of Class 600 ring joint gaskets with oval and octagonal cross sections. Five different sizes of gaskets are employed in the analysis, and one of them is newly designed on the basis of analysis results obtained from existing models. Three load steps are used to find the stress, stain and contact pressure etc., and to compare the contact characteristics among the models due to the bolt clamping force and the working surface pressure. ANSYS Workbench version15 is used to conduct the finite element analysis.

• The korean journal of orthodontics
• /
• v.15 no.2
• /
• pp.271-277
• /
• 1985

With modification of the acid etch technique and improvements of the physical and mechanical properties of the acrylic resin, the removal of directly bonded attachments and the finishing of the underlying enamel have become an acute clinical problem. This study was to evaluation the efficacy of recently introduced instrumentation and techniques to remove bonded brackets and residual resin, and restore the affected enamel surface to an acceptable clinical condition. Fortyeight premolar which were scheduled for extraction for orthodontic purposes were bonded with brackets using super-C ortho. Four additional premolars with untreated surfaces were used as controls. After one weak the brackets were removed and the residual resin removed by hand scaler, green stone, green rubber wheel, sandpaper disc, tungsten carbide bur, Sof-lex disc. Half the experimental teeth were given a final pumicing and then all were extracted and stored in 50 percent ethanol. The scanning electron microscopy was used to evaluated the enamel surface. Following results were obtained; 1. A satisfactory result was obtained by means of the Sof-lex disc. 2. The order of the scratch formation was the procedure using hand scaler, green atone, tungsten carbide bur, sandpaper disc, green rubber wheel, and Sof-lex disc. 3. The procedures using green stone and tungsten carbide bur showed many groove formations and the other procedures showed none. 4. final pumicing serves effectively to remove residual adhesive and restore the enamel surface.

• The Journal of Information Technology
• /
• v.9 no.4
• /
• pp.57-63
• /
• 2006

The intelligent elder brother groove network robot service the new broadband presence line is conversionce application service. Robot control data transmission hazard UDP packet of the remote control data which stands duplication necessary to transmit. TCP the error ratio to be high qualitative recording transmission pattern it of the transmission unit and is irregular the distance is distant to show and also the transmission lag is visible increases. The recording packet drop whose UDP degree error ratio will be high is frequent and does not arrive packet little by little increases is a possibility of knowing in the transmission unit. The technique which it proposes with traffic pattern of the transmission unit is visible the transfer characteristic of the same shape from 1% packet error ratio degree. The effective transmission technique of the robot control data which puts a base in UDP protocols was proposed from the present paper. Following research it leads and it follows the duplication transmission number of time in error rate of radio link and it was thought all that controls petty the research of the mechanism which progresses is necessary.

• Journal of the Korean Institute of Gas
• /
• v.11 no.2 s.35
• /
• pp.37-42
• /
• 2007

This paper presents the leakage safety of two O-rings, which are located at the rectangular groove between a valve body and a valve stem. The leakage safety analysis of 0-ring seals has been computed as functions of a compression set and a liquefied petroleum gas pressure of a LPG cylinder using a FEM program, MARC. The FEM computed results indicate that the loads from the filling pressure of $8kg/cm^2$ to the upper limit of the safety valve, $24.8kg/cm^2$ work safely according to the pressure vessel code. But two O-rings should consider the aging effects for an increased safety of the o-ring.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.12
• /
• pp.177-184
• /
• 2001

C3M(chemical mechanical micro machining) is applied for diminishing the size of burr and fabricating the massless patterning for aluminium wafer(thickness of 1${\mu}m$). It is difficult to perform the micro size machining with the radically increased shear stress. While the miniaturization and function-orientation of parts has been needed in the many field such as electronics, optics and medicine. etc., it is not enough to satisfy the industry needs in the machining technology. In this paper feasibility test of diminishing burr and fabricating maskless pattern was experimented and analyzed. In the experiment oxide layer was farmed on the aluminium with chemical reaction by ${HNO_3}$(10wt%), then the surface was grooved with tungsten carbide tool for the different condition such as the load and fred rate. The result was compared with the conventional machining to show the improvement of C3M with SEM for burr diminish and XPS for atomic existence, AFM for more precise image.

• Journal of KSNVE
• /
• v.4 no.4
• /
• pp.435-442
• /
• 1994

Self-Compensating Dynamic Balancer (SCDB) is composed of a circular disk with a groove containing spherical balls and a low viscosity damping fluid. To investigate the stability of the motion equations these equations are perturbed and the resulting perturbation equations are analyzed further to determine whether the perturbations grow or decay with dimensionless time. Based on the results of stability investigation, ball positions that result in a balanced system are stable above the critical speed for .betha.' = 3.8. At critical speed the perturbed motion is said to be stable for .betha.' = 23. However, the system is unstable below critical speed in any case of .betha.'.

• Fire Science and Engineering
• /
• v.31 no.4
• /
• pp.65-70
• /
• 2017

The seismic performance of press fittings is studied, which is one of the weldless joints of stainless steel pipe used in the water piping of recent fire protection system. The piping of this study was constructed based on the piping connection reference of NFPA 13. The permissible displacement of the piping was set as the allowed amount which is given in the Building Structure Standard, and the measurements were repeated 10 times. The Von-mises stress of the piping was 2.48 and 1.25 times of the allowed amount of stress, which was less than the standard, noted three times on the NPPs Allowable Stress for Level D service loading. Therefore, the press fittings shows enough seismic performance.

• Restorative Dentistry and Endodontics
• /
• v.12 no.2
• /
• pp.111-116
• /
• 1987

The experimental study was made to evaluate the influence of retentive grooves on the canal wall upon the retention of post, using different type of cements. Ninety periodontally involved anterior teeth were extracted and divided into six groups of 15 teeth. The groups were labeled as follows: Group I: Dentatus post cemented zincphosphate cement into post hole with smooth wall. Group II: Dentatus post cemented with zincphosphate cement into post hole with retentive grooves. Group III: Dentatus post cemented with glass-ionomer cement into post hole with smooth wall. Group IV: Dentatus post cemented with glass-ionomer cement into post hole with retentive grooves. Group V: Dentatus post cemented with composite resin adhesive into post hole with smooth wall. Group VI: Dentatus post cemented with composite resin adhesive into post hole with retentive grooves. The tensile strength was tested by an Instron type tester with cross-head speed of 5mm per minute. The results were as follows: In the group without retentive grooves, three kinds of cement have little effect upon retentive capacity of Dentatus post. The Dentatus post cemented on the canal wall with retentive grooves is more retentive than Dentatus post without retentive grooves.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.5
• /
• pp.49-55
• /
• 2017

In the seventies, a number of researchers carried out experiments on pullout tests with prototype equipment, and the pullout test was certified as a reliable nondestructive testing(NDT) method for determining the strength of concrete. To estimate the strength of high-strength concrete, we propose a simplified pullout test that uses as a break-off bolt a standard 10mm bolt with a groove on the shaft, an insert nut, and a pullout instrument that includes a hydraulic oil pump without a load cell. To verify the advantages of the simplified pullout test(low cost, simplicity, and convenience), four wall specimens were tested with two levels of concrete strength, 30 MPa and 50 MPa, using a simplified pullout tester with a load cell. The pullout load and concrete compressive strength were measured every day until day 7, day 14, day 21 and day 28. It was found that the pullout load was very similar to the compressive strength. Therefore, we have verified that a simplified pullout test can be used to evaluate the in-place strength of high-strength concrete in structures. The prediction equation of the groove diameter of the break-off bolt(y) with the concrete strength(x) was derived as y=0.05x+3.79, with a coefficient of determination of 0.88 found through regression analysis.

• The Journal of Korean Academy of Prosthodontics
• /
• v.8 no.1
• /
• pp.30-36
• /
• 1968

The measurements on the various items, such as arch form, kinds of anterior dental arch, degree of curvature in anterior dental arches, relationship between direction of the disto-incisal edge of the canine and first premolar, and kinds of posterior dental arch in upper dental arches were studied on 311 cases of the Korean adults aged from 20 to 30years. The results were as follows. 1. The commonest type of the upper dental arches was U-type (53.7%), the remaining were O-type (25.4%) and V-type (20.0%). 2. A slight curvature type (71.87%) prevailed against angulated curvature type in upper anterior dental arches. 3. The degree of curvature from $121^{\circ}$ to $160^{\circ}$ in anterior dental arches was common, and the degree of curve of 1-type with on curvature was smaller than 4, 5 type with two curvature. 4. The direction of the disto-incisal edge of canine went between the tip of the buccal cusp and the lingual incline of the buccal cusp of the first premolar in most dental arches and went lingual incline of the buccal cusp of the first premolar in U-type, from buccal cusp to lingual cusp of the first premolar in O-type and were distributed from buccal edge to central groove of the first premolar in V-type. 5. A posterior dental arch with almost straight curvature was common in 60.87%, and 4-type with a half rounded curve from first premolar to second molar was next.