• Steel and Composite Structures
• /
• 제52권2호
• /
• pp.135-143
• /
• 2024

Once the foundation displacement of the transmission tower occurs, additional stress will be generated on the tower members, which will affect the seismic response of transmission tower-line systems (TTLSs). Furthermore, existing research has shown that the reciprocating slippage of joints needs to be considered in the seismic analysis. The hysteretic behavior of joints is obtained by model tests or numerical simulations, which leads to the low modeling efficiency of TTLSs. Therefore, this paper first utilized numerical simulation and model tests to construct a BP neural network for predicting the skeleton curve of joints, and then a numerical model for a TTLS considering the bolt slippage was established. Then, the seismic response of the TTLS under foundation displacement was studied, and the member stress changes and the failed member distribution of the tower were analyzed. The influence of foundation displacement on the seismic performance were discussed. The results showed that the trained BP neural network could accurately predict the hysteresis performance of joints. The slippage could offset part of the additional stress caused by foundation settlement and reduce the stress of some members when the TTLS with foundation settlement was under earthquakes. The failure members were mainly distributed at the diagonal members of the tower leg adjacent to the foundation settlement and that of the tower body. To accurately analyze the seismic performance of TTLSs, the influence of foundation displacement and the joint effect should be considered, and the BP neural network can be used to improve modeling efficiency.

• Steel and Composite Structures
• /
• 제22권1호
• /
• pp.45-61
• /
• 2016

The domestic and foreign scholars conducted many studies on mechanical properties of wave web steel beam and high-strength spiral stirrups confined concrete columns. Based on the previous research work, studies were conducted on the anti-seismic property of the end plate bolt connected wave web steel beam and high-strength spiral stirrups confined concrete column nodes applied with pre-tightening force. Four full-size node test models in two groups were designed for low-cycle repeated loading quasi-static test. Through observation of the stress, distortion, failure process and failure mode of node models, analysis was made on its load-carrying capacity, deformation performance and energy dissipation capacity, and the reliability of the new node was verified. The results showed that: under action of the beam-end stiffener, the plastic hinges on the end of wave web steel beam are displaced outward and played its role of energy dissipation capacity. The study results provided reliable theoretical basis for the engineering application of the new types of nodes.

• Steel and Composite Structures
• /
• 제26권5호
• /
• pp.621-634
• /
• 2018

Flush end-plate (FEP) beam-to-column joints are commonly used for gravity load resisting parts in steel multi-storey buildings. However, in seismic resisting structures FEP joints should also provide rotation capacity consistent with the global structural displacements. The current version of EN1993-1-8 recommends a criterion aiming at controlling the thickness of the end-plate in order to avoid brittle failure of the connection, which has been developed for monotonic loading conditions assuming elastic-perfectly plastic behaviour of the connection's components in line with the theory of the component method. Hence, contrary to the design philosophy of the hierarchy of resistances implemented in EN1998-1, the over strength and the hardening of the plastic components are not directly accounted for. In light of these considerations, this paper describes and discusses the results obtained from parametric finite element simulations aiming at investigating the moment-rotation response of FEP joints under cyclic actions. The influence of bolt diameter, thickness of end-plate, number of bolt rows and shape of beam profile on the joint response is discussed and design requirements are proposed to enhance the ductility of the joints.

• 대한한의학원전학회지
• /
• 제35권1호
• /
• pp.137-153
• /
• 2022

Objectives : This paper aims to examine the meaning of guanjie(關節) in the Huangdineijing. Methods : Meanings of guan(關) and jie(節) were examined within the Neijing, after which the meaning of guanjie was studied in reference to usages of guan and jie. Other terms used similarly to guanjie were also studied. Results & Conclusions : 1. The meaning of guanjie in the Huandineijing could be inferred to meanings such as 'vital point and node', 'node of entrance gate', 'entrance gate and node', 'bolt and node', 'node of bolt', etc. 2. Most usages of guanjie in the Huangdineijing referred to 'pivotal node', while those mentioned in relation to edema or joint pain from wind and dampness meant 'node of entrance gate.' 3. The four entrances, eight nodes, extremity node, eight hollows, eight nodes of the limbs, twelve nodes, which are used similarly to guanjie, manage the five zang, communicate intimately via qi, while shen qi or zhen qi enter and exit. 4. Guanjie is closely linked to the five zang, while it is the entrance gate or pivotal node through which shen qi roams and travels. Therefore when interpreting a verse that includes 'guanjie', one must be aware of the perspectives of the Huangdineijing on qi, keeping in mind the close relationship with the five zang, and that zhen qi enters and exits.

• 한국기계가공학회지
• /
• 제6권2호
• /
• pp.3-8
• /
• 2007

Nonlinear property and contact matter are analyzed about the pipe applied with internal pressure through this study. The weakest part and its safety can be examined. Maximum equivalent stress is shown at the contact surface between bolt and nut. The value of contact stress with the pressure of 12MPa is increased 1.4 times as large as that with no pressure. The maximum contact pressure is shown at the clamp corner of the external surface on pipe. The value of contact pressure with the pressure of 12MPa is increased 1.4 times as large as that with no pressure. The radial deformation with no pressure is also increased greatly at the middle part of internal surface on pipe. But this maximum deformation on pipe with the pressure of 12MPa is shown at the part far away the support of pipe. This value is increased 5.7 times as large as that value with no pressure. As contact status, the sticking occurs most at the external surface of pipe. It also tends to occur at the contact surface between bolt and nut. At the external surface of pipe, the sticking in case of the pressure of 12MPa occurs more than that in case of no pressure.

• 한국구조물진단유지관리공학회 논문집
• /
• 제16권2호
• /
• pp.49-57
• /
• 2012

최근 교량의 건설에서는 공사기간의 단축 등을 위해 조립식 형태의 교량 시공이 연구되고 있다. 하지만 이는 대부분이 주 구조물인 교각, 거더와 바닥판 등에 국한되어 있고, 조립식 교량에 적합한 방호울타리와 같은 부대시설에 대한 연구는 미흡한 실정이다. 이에 본 연구에서는 조립식 교량 적용을 위한 콘크리트 방호울타리 연결 시스템을 제안하고, 제안된 시스템의 구조적 성능을 검증하기 위하여 정적 실험을 수행 하였다. 변수는 볼트의 수직 수평 접합방식으로 기준실험체와의 비교를 통해 조립식 교량에 적합한 콘크리트 방호 울타리 연결시스템을 제안하고자 하였다. 그 결과, 볼트의 수직접합이 구조적 성능 및 건전성이 일체형의 기준실험체와 거의 동일하다는 것을 알 수 있었고, 조립식교량 적용을 위한 연결시스템으로 적당하다고 판단된다.

• Structural Engineering and Mechanics
• /
• 제72권5호
• /
• pp.557-568
• /
• 2019

Accurate modeling of contact interface in bolted joints is crucial in predicting the dynamic behavior for bolted assemblies under external load. This paper presents a contact pressure distribution based non-uniform virtual material method to describe the joint interface of assembly structure, which is connected by sparsely distributed multi-bolts. Firstly, the contact pressure distribution of bolted joints is obtained by the nonlinear static analysis in the finite element software ANSYS. The contact surface around bolt hole is divided into several sub-layers, and contact pressure in each sub-layer is thought to be evenly. Then, considering multi-asperity contact at the micro perspective, the relationship between contact pressure and interfacial virtual material parameters for each sub-layer is established by using the fractal contact theory. Finally, an experimental platform for the dynamic characteristics testing of a beam lap structure with double-bolted joint is constructed to validate the efficiency of proposed method. It is found that the theoretical results are in good agreement with experimental results by impact response in both time- and frequency-domain, and the relative errors of the first four natural frequencies are less than 1%. Furthermore, the presented model is used to examine the effect of rough contact surface on dynamic characteristics of bolted joint.

• 한국정밀공학회지
• /
• 제24권3호
• /
• pp.108-116
• /
• 2007

To overcome many defects such as the high product cost, large energy consumption, and big space capacity in conventional mechanical machining, the miniaturization of machine tool and micro factory systems has been envisioned recently. The object of this paper is to research the effect of dynamic characteristic parameters in bolted-joint beams, which is widely applied to the joining of mechanical structures in order to identify structural system characteristics and to predict dynamic behavior according to scale-down from macro to micro system as the development of micro/meso-scale machine tool and micro factories. Modal parameters such as the natural frequency, damping ratio, and mode shape from modal testing and dynamic characteristics from finite element analysis are extracted with all 12 test beam models by materials, by size, and by joining condition, and then the results obtained by both methods are compared.

• Steel and Composite Structures
• /
• 제31권1호
• /
• pp.99-112
• /
• 2019

Semi-rigid joints have been widely studied in literature in recent decades because they affect greatly the structural response of frames. In literature, the behavior of semi-rigid joints is commonly assumed to be identical under positive and negative moments which are obviously incorrect in many cases where joint details such as bolt arrangement or placement of haunch are vertically asymmetrical. This paper evaluates two common types of steel frames with asymmetrical beam-to-column joints by Direct Analysis allowing for plasticity. A refined design method of steel frames using a proposed simple forth order curved-quartic element with an integrated joint model allowing for asymmetrical geometric joint properties is presented. Furthermore, the ultimate behavior of six types of asymmetrical end-plate connections under positive and negative moment is examined by the Finite Element Method (FEM). The FEM results are further applied to the proposed design method with the curved-quartic element for Direct Analysis of two types of steel frames under dominant gravity or wind load. The ultimate frame behavior under the two different scenarios are examined with respect to their failure modes and considerably different structural performances of the frames were observed when compared with the identical frames designed with the traditional method where symmetrical joints characteristics were assumed. The finding of this research contributes to the design of steel frames as their asymmetrical beam-to-column joints lead to different frame behavior when under positive and negative moment and this aspect should be incorporated in the design and analysis of steel frames. This consideration of asymmetrical joint behavior is recommended to be highlighted in future design codes.

• Composites Research
• /
• 제23권1호
• /
• pp.37-43
• /
• 2010

이 연구에서는 볼트로 겹침이음된 펄트루젼 복합재의 접합부에 대한 구조적 거동을 실험적 연구를 통해 조사하였다. 펄트루젼 복합재 접합부의 구조적 거동 조사에 앞서 재료의 역학적 성질을 파악하기 위해 펄트루젼 복합재의 인장 및 전단실험을 수행하였고, 이를 바탕으로 볼트의 수와 배열을 변수로 3종류의 겹침이음 시편을 제작하였다. 겹침이음 접합부 실험은 접합부를 중심으로 인장하중이 작용하도록 하중을 재하하였고, 하중증가에 따른 접합부의 구조적 거동 및 파괴모드를 조사하였다. 실험결과 접합부에 대한 파괴는 대부분 전단파괴로 나타났으며, 실험을 통해 얻어진 데이터를 분석하여 설계를 위한 기초자료로 활용될 수 있도록 하였다.