• Journal of the Korean Wood Science and Technology
• /
• v.36 no.4
• /
• pp.66-76
• /
• 2008

Recently, demands for the structural uses with domestic Japanese larch and SPF(spruce-pine-fir) lumber from North America have been increased. Shear properties of nailed joints that are the most simple and optimum fastening method in wooden constructions, especially in light frame construction. For the nailed joints, in North America and Japan, a number of basic and practical studies have been performed. The shear behaviors for the double nailed joint with variations of member and its direction, were examined. Shear properties of the shear specimens with SPF stud showed more remarkable variation than larch glulam and larch stud. Furthermore, the relationships between slip modulus and strength are not coincided in every case.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.4
• /
• pp.99-107
• /
• 1997

This study was executed to test the possibility of replacement for domestic Japanese larch(Larix leptolepis) for hardwoods and to acquire the information about the effects of drying temperature on internal temperature, moisture content and drying defects. In high-temperature drying, internal temperature increased rapidly to boiling point, immediately after that point the internal temperature rising rate was reduced. In the case of drying at temperature of $125^{\circ}C$, internal temperature could reach at boiling point in a very short time. Moisture content in high-temperature drying showed constant drying rate period and first period of falling rate drying together in 4 hours since experiment begun. There was no strong correlation between initial moisture content and final moisture content. Average drying rate at $115^{\circ}C$, $120^{\circ}C$ and $125^{\circ}C$ was 1.42%/hr, 1.88%/hr and 2.02%/hr, respectively; the case of drying temperature of $125^{\circ}C$ showed most rapid drying rate. Drying rate of $125^{\circ}C$ was so rapid that it showed more severe shrinkage, bow, collapse, end check, and internal check development than in other drying conditions. The result of this study showed the strong possibility of high-temperature drying for Japanese larch, and to dry Japanese larch optimally, dry bulb temperature should not exceed $120^{\circ}C$.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.1
• /
• pp.27-31
• /
• 2003

This paper presents the results of air-drying processes and mositure content (MC) distribution of red pine (P. densiflora) and Japanese larch (L. leptolepis) square timber with 14 cm and 16.5 cm of face size, respectively. The air-drying rates of square timber were comparatively high during the first 8 weeks, after that gradually decreased. The time to air dry square timber from initial MC to specified MC of 18 percent required about 26 weeks for 14.0 cm and 32 weeks for 16.5 cm square of red pine, and 32 weeks for 14.0 cm and 48 weeks for 16.5 cm square of Japanese larch. The longitudinal- and transverse MC distribution of these air-dried squares showed slight moisture gradient. The effect of face size on moisture gradient of Japanese larch square was more pronounced comparing with red pine one.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.6
• /
• pp.666-674
• /
• 2014

In this study, we investigated mechanical properties of Korean softwoods after applying thermal compression. Density of compressed woods was notably increased with thermal compression. In case of 50% compression set, density of Korean pine (Pinus koraiensis), Japanese red pine (P. densiflora), and Larch (Larix kaempferi) wood was increased by 71%, 74%, and 76%, respectively, when compared to the control group. The strength of woods was increased and quality of the woods became homogeneous with an increases in the compression set. On the 50% compression set, the compressive strength, bending strength, and hardness of Korean pine wood was increased by 76%, 83%, and 55%, respectively compared to the control group. Longitudinal compressive strengths of Japanese red pine wood increased by 69%, 130%, and 76%, respectively and those of Larch wood increased by 77%, 120%, and 44%, respectively. In thermal compression wood, mechanical properties of Larch wood was the highest, while those of Korean pine wood were the lowest. However, Japanese red pine wood showed the highest in the increase rate of mechanical properties after the thermal compression.

• Journal of the Korean Wood Science and Technology
• /
• v.13 no.3
• /
• pp.41-48
• /
• 1985

In near future about 500,000 hectares of Japanese larch and pitch pine need thinning to improve crop-tree spacing and reasonable species composition in Korea. Although thinned trees show very little high quality wood, in fact, all the sawed products are suitable for construction and farming materials. Studies on the utilization of thinned small-diameter trees have been implemented in order to increase lumber yield and display the skeleton of farm buildings. The results obtained in this study were summarized as follows: 1. According to Korean Conifers Log Grading System, log grade 3 was 87.4 percent in Japanese larch bolts and 95.8 percent in pitch pine bolts from thinned trees. The ability to identify defects was essential for grading logs. 2. Cutting diagrams of sawing were developed for 1-sided sawing, 2-sided sawing and 3-sided sawing by small end diameter class of bolt and cutting sizes also were found to use effectively lumber with wane. 3. Lumber recovery of Pitch pine was a little higher than that of Japanese larch. The maximum lumber yields of pitch pine by sawing patterns were 87.2 percent for 1-sided sawing, 80.8 percent for 2-sided sawing an 64.1 percent for 3-sided sawing, up yield compared with 58.1 percent for 4-sided sawing. The lumber yield of 1, 2 and 3-sided sawing significantly was higher value than that of 4-sided sawing. 4. Lumber was inspected and graded. Lumber quality of diameter class 12cm was a little better than that of diameter class 8cm, but 90 percent of lumber in diameter c1ass 16cm fell into grade 3. The lumber grade was classified by Korean standard grades of confiers lumber. 5. Lumber from 1, 2 and 3-sided sawing was used to build the skeleton of a farm house ($53m^2$) and greenhouse ($60m^2$) in order to display more efficient use of small diameter trees from thinning 6. Total volume of timber for building a farm house was $8.1m^3$ of imported timber. Timber of $7m^3$, 70 percent of total volume would be substituted imported timber for domestic timber.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.1
• /
• pp.34-47
• /
• 1996

Veneers of two nominal thicknesses, 1.5 and 2.5mm, were rotary peeled from Japanese larch (Larix leptolepis). Dahurian larch (Larix gmelinei) and Radiata pine (Pinus radiata) bolts unheated and heated in the water vat temperature of $66^{\circ}C$ by rising a final temperature at 10cm core of $60^{\circ}C$ to remain core diameter of 11.4cm. 1.5 and 2.5mm thick veneer cut from the heated Japanese larch were significantly thinner than those of the unheated bolt and 2.5mm thick veneer cut from the heated Dahurian larch were significantly thicker than that of the unheated bolt. 1.5mm thick Dahurian larch veneer and 1.5 and 2.5mm thick Radiata pine veneers showed insignificant difference between the unheated and heated bolts, respectively. Check distance on the loose side of 1.5mm thick veneer cut from the heated Radiata pine was significantly wider than that of the unheated bolt. However check distances on the loose side of 1.5 and 2.5mm thick Japanese larch and Dahurian larch veneers and 2.5mm thick Radiata pine veneers showed insignificant difference between the unheated and heated bolts. Also the depth of check on the loose side of three species showed insignificantly difference between the unheated and heated bolts. Arithmatic mean deviation($R_a$) and maximum height($R_{max}$) of the profile on the loose side of dried veneer by preheating the bolt compared with unheated bolts were different among apecies and between veneer thickness. The preheating treatment slightly affected qualities of these thin veneers such as 1.5 and 2.5mm. The yield of 2.5mm thick veneer from the heated radiata pine was significantly higher than that of the unheated bolt. However the yield of 2.5mm thick veneer for other two species and 1.5mm thick veneer for three species showed insignificant difference between the unheated and heated bolts. The yield of 2.5mm thick veneer for three species were higher than those of 1.5mm thick veneer. The average yields of green veneer of Japanese larch. Dahurian larch and Radiata pine were 57.1, 55.1 and 54.0 percent, respectively. Variables such as initial MC. drying time and veneer thickness had strong effect for Japanese larch veneer, less effect for Radiata pine veneer and nuch less effect on final MC for Dahurian larch veneer in jet drying. Correlation between the current MC and the drying time of Dahurian larch with low variation of initial MC was higher than those of Japanese larch and Radiata pine veneer with high variation of initial MC in high temperature drying. Thickness shrinkages of 2.5mm thick veneer for Japanese larch and Radiata pine were higher than those of 1.5mm thick veneers, but shrinkages of Dahurian larch veneer were similar between two nominal veneer thicknesses.

• Journal of Korean Society for Atmospheric Environment
• /
• v.27 no.4
• /
• pp.436-442
• /
• 2011

In this study, the Total Volatile Organic Compounds (TVOC) emitted from wood-based panels were compared by two analytical methods using the GC/FID and the GC/MS. Japanese Larch, Yellow Poplar, Particle Board (PB) and Medium Density Fiberboard (MDF) were selected as target materials. Major compounds emitted from the panels were Toluene, ${\alpha}$-pinene, ${\beta}$-pinene and limonene. In case of TVOC using GC/FID method, MDF E2 (1,497 ${\mu}g/m^3$) revealed the highest concentration among all wood-based panels, while Japanese Larch (1,772 ${\mu}g/m^3$) showed the highest value with respect to GC/MS method. Furthermore, it was found that the amount of VOC emitted from panels was different depending upon analytical methods. This significant difference was attributed to analytical sensitivities of GC/FID and GC/MS for various VOC. Besides, it was found that the composition ratios of main VOC compounds were not significantly different.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.6
• /
• pp.88-95
• /
• 2008

The shrinkage of wood members after construction has been a greater and common concern in wooden buildings with the durability. Particularly, the traditional structure applying solid members actively is easily exposed to the shrinkage that caused by the joints, members, and walls. Moreover, even though domestic larch glulam members are widespread recently in the post-beam construction, the shrinkage (swelling) problem is still the critical defect on the wooden structures by the moisture content change in Korea. Various moisture contents were applied for the specimens to survey the dimensional changes for Japanese larch solid and glulam specimens, and the glulam specimens varied in the number of their laminations. Test results showed that glulam specimens with over 3 bonding layers showed good dimension stabilities. Therefore, to solve the shrinkage problem, sufficient drying fitted to the end-use service conditions should be conducted on the solid or glulam members can be applied.

• Journal of the Korean Wood Science and Technology
• /
• v.9 no.2
• /
• pp.31-35
• /
• 1981

This study was carried out to investigate the properties of hardboard made from fire killed larch tree and also effects of standing period after killed by fire. The results are as follows; 1. There were no effects on hardboard properties among the standing period differences after killed by fire within about 2 years. 2. Specific gravities, moisture contents, water absorptions of the boards from dead trees have no differences compared with those of sound wood. 3. Bending strengths of the boards from dead trees we re decreased in the range of 24-28% of the boards from sound wood.

• Journal of the Korean Wood Science and Technology
• /
• v.28 no.4
• /
• pp.61-71
• /
• 2000

The effect of the treatment with CCFZ, FR-4, and PEG400 from butt end on the dimensional stability and bending properties was examined. Three softwood species such as red pine, Korean white pine and Japanese larch and three hardwood species such as poplar, alder and oak were investigated in this research. Shrinkage of red pine, Korean white pine, poplar, and alder treated with PEG400 decreased. However, there was no significant decrease of shrinkage in Japanese larch and oak. The decrease of shrinkage when moisture content changed from about 20% to 10% was larger than that at any other phase. In regard to the effect of treatment on bending properties, bending MOE and MOR of all specimens treated with PEG400 decreased significantly. Especially in the case of red pine, poplar, and alder treated with PEG400, bending MOR reduced 9%, 14%, and 12%, respectively. Reductions of MOR of the hardwood was also much larger than that of the softwood. However, in all species, treatment with CCFZ and FR-4 did not affect the change of bending MOE and MOR significantly. Comparing the large specimen which also included heartwood with the small specimen which included only treated sapwood, there was a difference in the change of bending MOE and MOR between them. The large specimens of Korean white pine, alder and Poplar, which had a relatively low proportion of sapwood(18~22%), showed the decrease of MOR by 11~13% more than that of small specimens, while red pine, Japanese larch and oak, which had a relatively high proportion of sapwood(35~40%), showed little decrease. It means that bending MOE and MOR of structural wood treated from butt end should be considered in terms of sapwood proportion as well as effect of treated chemicals.