• Journal of Industrial and Engineering Chemistry
• /
• v.67
• /
• pp.448-460
• /
• 2018

Copper nanoparticle-doped and graphitic carbon nanofibers-covered porous carbon beads were used as an efficient catalyst for treating synthetic phenolic water by catalytic wet air oxidation (CWAO) in a packed bed reactor over 10-30 bar and $180-230^{\circ}C$, with air and water flowing co-currently. A mathematical model based on reaction kinetics assuming degradation in both heterogeneous and homogeneous phases was developed to predict reduction in chemical oxygen demand (COD) under a continuous operation with recycle. The catalyst and process also showed complete COD reduction (>99%) without leaching of Cu against a high COD (~120,000 mg/L) containing industrial wastewater.

• Asian-Australasian Journal of Animal Sciences
• /
• v.12 no.4
• /
• pp.537-543
• /
• 1999

Whole horse beans (Vicia faba cv. Alfred) (WHB) were pressure toasted at different temperatures of 100, 118 and $136^{\circ}C$ for 3, 7, 15 and 30 minutes in order to determine an optimal heating conditions to increase bypass starch (BPSt) as glucose source which is usually limiting nutrient in highly producing dairy cows in the Netherlands. Starch (St) Ruminal Degradative Kinetics and Fermentation Characteristics of (SRDC) of WHB were determined using in sacco technique in 4 lactating dairy cows fed 47% hay and 53% concentrate according to Dutch dairy cow requirements. Measured characteristics of St were soluble fraction (S), potentially degradable fraction (D) and rate of degradation (Kd) of insoluble but degradable fraction. Based on measured characteristics, percentage bypass starch (BPSt) was calculated according to the Dutch new feed evaluation system: the DVE/OEB system. Pressure toasting temperatures significantly affected starch gelatinization (p<0.01). Degradability of Starch in the rumen was highly reduced by pressure toasting (p<0.01). S varied from 58.2% in the raw WHB (RWHB as a control) to 19.6% in $136^{\circ}C/15min$. S was reduced rapidly with increasing time and temperature (p<0.01). D varied from 41.8% in RWHB to 80.5% in $136^{\circ}C/15min$. D fraction was enormously increased with increasing time and temperature (p<0.01). Kd varied from 4.9%h in RWHB to 3.4%/h in $136^{\circ}C/15min$. All these effects resulted in increasing %BPSt from 29.0% in RWHB to 53.1% in $136^{\circ}C/15min$. Therefore BPSt increased from 93.5 g/kg in RWHB to 173.5 g/kg in $136^{\circ}C/15min$. The effects of pressure toasting on %BPSt and BPSt seemed to be linear up to the highest values tested. Therefore no optimal pressure toasting conditions could be determined at this stage. But among 10 treatments, The treatment of $136^{\circ}C/15min$was the best with the highest BPSt content. It was concluded that pressure toasting was effective in shifting starch degradation from rumen to small intestine to increase bypass starch.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05d
• /
• pp.82-85
• /
• 2003

산업의 고도화 및 환경오염의 문제로 1970년대부터 실리콘고무를 이용한 애자의 사용이 시도되기 시작되었다. 그로 인해 실리콘 고무의 표면열화에 대한 수많은 연구가 현재까지 행해지고 있다. 그러나 고온성 형압즉방식으로 제작하는 유기애자의 경우 제조시 발생할 수 있는 내부보이드에 대한 연구는 미흡한 현실이다. 이에 본 연구에서는 실리콘고무의 내부보이드의 형태변화에 따른 전기적열화특성을 연구하기 위하여 3층으로 적층시킨 실리콘 고무의 중간층에 임의적으로 4가지형태의 내부보이드를 성형하여 전압을 변화시키면서 방전전류 및 방전전력을 측정하였다. 그 결과, 보이드의 존재로 방전전류 및 방전전력의 증가를 볼 수 있었으며, 보이드형상의 내부각이 좁을수록 방전전류 및 방전전력값이 커지는 것을 볼 수 있었다.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.34C no.11
• /
• pp.66-75
• /
• 1997

We derive the system design parameters to implement the receiving system for the PCS mobile station to satisfy the J-sTD-018 which is the PCS mobile station(MS) minimum performance. Also we analyze the system performance and intermodulation spurious due to the values of a device cause the system performance degradation, is proposed. The simulation shows the receiver's maximum system noise figure to satisfy the receiver selectivity is approximately 11 dB. While the MS noise figure is 10dB with system margin 1 dB, the minimum selectivity is -71 dB at 1.25MHz frequency offset from the carrier frequency. And the input 3rd order intercept point of the MS class I and the MS class II~V is -9.5 dBm and -14dBm respectively. When the interference power level at the receiver is small, the receiver has better performance as we increase the gain of the LNA. However, when the interference level at the receiver is large, the receiver performance is heavily affected by the spurious as we increase the gain of the LNA. Thus, we proved the effectiveness of the LNA On/Off switching technique as to reduce the effect of the spurious.

• Transactions of the Korean hydrogen and new energy society
• /
• v.22 no.6
• /
• pp.827-834
• /
• 2011

Epoxy/graphite/expanded graphite composites have been prepared in various weight ratios and thermal degradation and electrical properties were estimated in order to use for the bipolar plate materials in PEMFC. Thermogravimetric analysis (TGA) showed that the epoxy/graphite system cured by a curing agent GX-533 was most proper because its weight loss until $80^{\circ}C$ at which PEMFC would be operated was 0.3 wt%, and differential scanning calorimetry (DSC) analysis showed its cure temperature would be sufficient at $80^{\circ}C$. The activation energy for the cure reaction was 132.0 kJ/mol and the pre-exponential factor was $1.76{\times}10^{17}min^{-1}$. Electrical conductivity on the surface of the bipolar plate prepared under a pressure of 200 $kgf/cm^2$ was increased from 4 to 25 $S/cm^2$ by increasing expanded graphite (EG) content from 50 phr to 90 phr. The percolation threshold was initiated around 75 phr and the corrosion rate at 80 phr was 1.903 $uA/cm^2$.

• Journal of the Korean Chemical Society
• /
• v.57 no.6
• /
• pp.712-720
• /
• 2013

Microwave assisted syntheses of Zn(II), Cd(II) and Hg(II) complexes with 3-aminopyridine (3AP) and nitrite ($NO_2{^-}$) ions have been reported. The metal complexes were characterized by elemental analyses, molar conductance, IR, Far-IR, electronic, NMR ($^1H$, $^{13}C$), thermal and electron impact mass spectral studies. The spectroscopic studies reveal the composition, the nature of nitrite ligand in the complexes, electronic transitions, chemical environments of C and H atoms thermal degradation of the complexes. On the basis of characterization data, distorted tetrahedral geometry is suggested for Zn(II), Cd(II) and Hg(II) complexes. The organic ligand (3AP) and their metal complexes were screened against gram negative pathogenic bacteria and fungi in vitro. The results are compared with our previous report J. Korean Chem. Soc. 2013, 57, 341 on 4-aminopyridine and nitrite ion complexes of the same metal ions.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.1
• /
• pp.55-60
• /
• 2012

In order to develop electroless-plated Nickel Phosphate (Ni-P) as a contact material for high efficient low-cost silicon solar cells, we evaluated the effect of ambient thermal annealing on the degradation behavior of interfacial adhesion energy between electroless-plated Ni-P and silicon solar cell wafers by applying 4-point bending test method. Measured interfacial adhesion energies decreased from 14.83 to 10.83 J/$m^2$ after annealing at 300 and $600^{\circ}C$, respectively. The X-ray photoelectron spectroscopy analysis suggested that the bonding interface was degraded by environmental residual oxygen, in which the oxidation inhibit the stable formation of Ni silicide phase between electroless-plated Ni-P and silicon interface.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1277-1279
• /
• 1994

In the structure of ZnO/nip-SiC: H/metal substrate amorphous silicon (a-Si:H) solar cells, the effects of inserting a rear textured ZnO in the p-SiC:H/metal interface and a graded bandgap buffer layer in the i/p-SiC:H have been analysed by computer simulation. The incident light was taken to have an intensity of $100mW/cm^2$(AM-1). The thickness of the a-Si:H n, ${\delta}$-doped a-SiC:H p, and buffer layers was assumed to be $200{\AA},\;66{\AA}$, and $80{\AA}$, respectively. The scattering coefficients of the front and back ZnO were taken to be 0.2 and 0.7, respectively. Inserting the rear buffer layer significantly increases the open circuit voltage($V_{oc}$) due to reduction of the i/p interface recombination rate. The use of textured ZnO markedly improves collection efficiency in the long wavelengths( above ${\sim}550nm$ ) by back scattering and light confinement effects, resulting in dramatic enhancement of the short circuit current density($J_{sc}$). By using the rear buffer and textured ZnO, the i-layer thickness of the ceil for obtaining the maximum efficiency becomes thinner(${\sim}2500{\AA}$). From these results, it is concluded that the use of textured ZnO and buffer layer at the backside of the ceil is very effective for enhancing the conversion efficiency and reducing the degradation of a-Si:H pin-type solar cells.

• Nuclear Engineering and Technology
• /
• v.55 no.5
• /
• pp.1855-1862
• /
• 2023

Graphite crucibles are used for melting uranium and its alloys in VIM furnace. Various coating materials namely Al₂O₃, ZrO₂, MgO etc. are applied on the inner surface of the crucibles using paint brush or thermal spray technique to mitigate U-C interaction. These leads to significant amount of carbon pick-up in uranium. In this study, the attempts are made to develop multilayer coatings comprising of SiC/Y₂O₃ and Mo/Y₂O₃ on graphite to study the feasibility of minimizing U-C interaction. The parameters are optimized to prepare SiC coating of about 70㎛ thickness using CVD technique on graphite coupons and subsequently Y₂O₃ coating of about 250㎛ thickness using plasma spray technique. Molybdenum and Y₂O₃ layers were deposited using plasma spray technique with 70㎛ and 250㎛ thickness, respectively. Interaction studies of the coated graphite with molten uranium at 1450℃ for 20 min revealed that Y₂O₃ coating with SiC interlayer provides physical barrier for uranium-graphite interaction, however, this led to the physical separation of coating layer. Y₂O₃ coating with Mo interlayer provided superior barrier effect showing no degradation and the coatings remained intact after interaction tests. Therefore, the Mo/Y₂O₃ coating was found to be a promising solution for minimizing carbon pick-up during uranium/uranium alloy melting.

• Applied Chemistry for Engineering
• /
• v.10 no.7
• /
• pp.1052-1060
• /
• 1999

Tire and raw material of tire, i.e., SBR were degraded using pyrolysis process. The yield of pyrolytic oil was increased and that of gas was decreased with increase of operating temperature in pyrolysis. And the yield of pyrolytic oil was increased and that of gas and char was decreased with increase of heating rate. The maximum oil yields of SBR and tire were 86% and 55% each at $700^{\circ}C$ with a heating rate of $20^{\circ}C/min$. The number average molecular weight ranges of SBR and tire were 740~2486, 740~1719, and the calorific value of SBR and tire was 39~40 kJ/g. The oil components were consisted of mostly 50 aromatic compounds. The particle size was decreased and the surface area was increased with increase of operating temperature, and the BET surface area was $47{\sim}63m^2/g$. The optimum condition of pyrolysis was the temperature of $700^{\circ}C$ with heating rate of $20^{\circ}C$, and the reactor was continuously purged with inert gas to sweep the evolved gases from the reaction zone.