• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.996-999
• /
• 2008

Aspheric polymer lens fabrication using isothermal compression molding is presented in this paper. Due to increasing definition of an image sensor, higher precision is required by a lens which can be used as a part of an imageforming optical module. Injection molding is a factory standard method for a polymer optical lens. But achievable precision using injection molding has a formidable limitation due to the machining of complex mold structure and melting and cooling down a polymer melt under high pressure condition during forming process. To overcome the precision requirement and limitation using injection molding method, isothermal compression molding is applied to fabrication of a polymer optical lens. The fabrication condition is determined by numerical simulations of temperature distribution and given material properties. Under the found condition, the lens having a high precision can successfully be reproduced and does not show birefringence which results often in optical degradation.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.05a
• /
• pp.190-193
• /
• 2001

Hot deformation behavior of Udimet 720Li was characterized by compression tests in the temperature range of $1025^{\circ}C\;to\;1150^{\circ}C$ and the strain rate rage of $0.0005s^{-1}\;to\;5s^{-1}$. In order to characterize the dependence of flow stress on strain, strain rate and temperature, a constitutive equation based on hyperbolic sine formation was used. Isothermal forging of Udimet 720Li was performed in the temperature range $1050-1150^{\circ}C$ at strain rates of $0.05s^{-1}\;and\;0.005s^{-1}$. FE simulation was also carried out to predict deformation microstructures during isothermal forging.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.9
• /
• pp.75-81
• /
• 1998

Simulations of warm and hot forming processes need reliable expressions of flow stress at high temperatures. To get flow stress of the materials usually tension, compression and torsion tests are conducted. In this study, hot compression tests were adopted to get flow stress of medium carbon steel. Experiments have been conducted under both isothermal, near constant strain rate in the temperature ranges 650～100$0^{\circ}C$. Phase transformation takes place by temperature changes for steels in hot and warm forging stage. So Constitutive equation are formulated as the function of strain, strain rate and temperature for isothermal conditions and phase transformation.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.03a
• /
• pp.98-105
• /
• 1997

The behaviour of alloys in the semi-solid state strongly depends on the imposed stress state and on the morphology of the phase which can very from dendritic to globular. The estimation of behaviour characteristic in the compression simulation with seim-solid materials are calculated by finite element method with proposed algorithm. The proposed theoretical model and a various boundary conditions for compression process is investigated with the coupling calculation between the liquid phase flow and the solid phase deformation. The simulation process considering soldification phenomena is performed to the isothermal conditions of two dimensional problems. To analysis of compression process by using semi-solid materials, a new stress-strain relationship is described, and compression analysis is performed by viscoelastic model for the solid phase and the Darcy's law for the liquid flow. The calculated results for compression force and ram displacement will be compared to experimental data.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.270-273
• /
• 2009

This work describes a method of determining material parameters included in recrystallization and grain growth models. Focus is on the recrystallization and grain growth models of Ni-Fe base superalloy, Alloy 718. High temperature compression tests at different strain, strain rate and temperature conditions were chosen to determine the material parameters of dynamic recrystallization model. The critical strain and dynamically recrystallized grain size and fraction at various process variables were quantitated with the microstructual analysis and strain-stress relationships of the compression tests. Besides, isothermal heat treatments were utilized to fit the material constants included in the grain growth model. Verification of the determined material parameters is carried out by comparing the measured data obtained from other compression tests.

• Transactions of Materials Processing
• /
• v.11 no.6
• /
• pp.538-546
• /
• 2002

Hot deformation behavior of Udiment720Li was characterized by compression tests in the temperature range of 10$25^{\circ}C$ to 115$0^{\circ}C$ and the strain rate range of $0.0005 s^{-1};to;5 s^{-1}$. The combination of dynamic material model (DMM) and Ziegler's instability criterion was applied to predict an optimum condition and unstable regions for hot forming. A dynamic recrystallization model coupled with FEM results was used to interpret the evolution of microstructures. In order to verify the reliability of the present coupled model, isothermal forging was performed in the temperature range 1050~115$0^{\circ}C$ at strain rates of $0.05 s^{-1};and;0.005 s^{-1}$. The present model was successfully applied to the hot forming process of Udimet720Li.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.5
• /
• pp.605-611
• /
• 2016

Mg alloy sheet exhibits significant differences in tensile and compressive yield stress depending on the temperature, as well as variations in its hardening behavior. Such unusual behavior makes it difficult to simulate the forming process of Mg alloy sheets. Results of analysis tend to deviate significantly from the experimental data because commercial software do not completely implement the unusual hardening behavior, yield asymmetry and temperature dependent changes in the Mg alloy's material properties. In the previous study, an in-plane tension-compression cyclic tester was developed to predict the cyclic behavior of Mg alloy sheets at an elevated temperature of up to $250^{\circ}C$. A new constitutive equation was suggested to analyze the unusual behavior, and was implemented in the commercial software in the form of user subroutine. In this paper, a stamping process of Mg seat cushion panel for automotive parts was simulated using the experimental data and user subroutine. Based on the analysis, an optimal temperature condition was determined and a stamping die shape at each step was suggested in the non-isothermal stamping of Mg alloy sheets.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.3
• /
• pp.796-805
• /
• 1996

A fabrication process using Semi-Solid Material(SSM) for casting alloy has been studied to demonstrate the possibility for mass production with controlled solid fraction. The SSM was fabricated under the various solid fractions and preheating temperatures of mold. The behaviour of a semi-solid global microstructure has been investigated under the various heating and die temperatures for solid fraction. The effect of reheating time on the globularization of SSM microstructure has been investigated in detail. And the behavior of SSM which has the solid fraction 0.5 was observed under compression. The stress strain relationship was also obtained for the compression test of semi-solid materials. The rheological behaviour of semi-solid with globule microstructure was investigated as a function of the compression velocity under isothermal holing conditions.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.7 s.166
• /
• pp.1075-1084
• /
• 1999

The family of unidirectional continuous fiber reinforced polymeric composites are currently used in automotive bumper beams and load floors. The material properties and mechanical characteristics of the compression molded parts are determined by the curing behavior, fiber orientation and formation of knit lines, which are in turn determined by the mold filling parameters. In this paper, a new model is presented which can be used to predict the 3-dimensional flow under consideration of the slip of mold-composites and anisotropic viscosity of composites during compression molding of unidirectional fiber reinforced thermoplastics for isothermal state. The composites is treated as an incompressible Newtonian fluid. The effects of longitudinal/transverse viscosity ratio A and slip parameter $\alpha$ on the buldging phenomenon and mold filling patterns are also discussed.

• Transactions of Materials Processing
• /
• v.20 no.7
• /
• pp.491-497
• /
• 2011

This work describes a method for determining material parameters included in recrystallization and grain growth models of metallic materials. The focus is on the recrystallization and grain growth models of Ni-Fe based superalloy, Alloy 718. High temperature compression test data at different strain, strain rate and temperature conditions were chosen to determine the material parameters of the model. The critical strain and dynamically recrystallized grain size and fraction at various process conditions were generated from the microstructural analysis and strain-stress relationships of the compression tests. Also, isothermal heat treatments were utilized to fit the material constants included in the grain growth model. Verification of the determined material parameters is carried out by comparing the average grain size data obtained from other compression tests of the Alloy 718 specimens with the initial grain size of $59.5{\mu}m$.