• Elastomers and Composites
• /
• v.36 no.3
• /
• pp.153-161
• /
• 2001

The rubber pads era tank which undergo dynamic deformations with the sufficient amplitudes and frequencies lead to a considerable internal temperature rise due to the heat generation. The heat generation which is dependent on the viscoelastic characteristics or a rubber is due to the conversion of partial mechanical energy into thermal energy identical to the area oi hysteresis loop. Heat generation without adequate heat dissipation leads to heat build-up and the excessive temperature rite exerts a bad influence upon the performance and the life of rubber products. In this paper, temperature distributions of the rubber pads of a tank track subjected to dynamic loads are obtained under the assumption of the steady state. Heat generation rates used in this finite element analysis are acquired through experiments and the computed temperature fields are displayed in isothermal contour regions.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.05a
• /
• pp.34-35
• /
• 2019

In recent years, the construction industry has also applied the dry method that can be assembled in the field by industrialization and factory production, which is free from climatic effects and can reduce the cost due to mass production and simplify the work in the field. Among the building materials used in this dry method, ALC products are made by mixing calcium oxide, gypsum, cement, and water in silica and putting them in an autoclave to create voids in the interior through steam curing at high temperature and pressure. But it requires curing cycle conditions of warming, isothermal, and temperature curing. It depends on the performance of the product depending on the curing conditions, the economical efficiency due to high oil prices, the emission of greenhouse gases by the use of fossil fuels. Experiments were conducted to select an appropriate animal protein foam for lightweight foamed concrete block which was cured by applying a prefilling method to replace existing ALC products. As a result of investigating the characteristics of lightweight foamed concrete by type of animal protein foam, it is considered that FP3 is most suitable for manufacturing lightweight foamed concrete block.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.12
• /
• pp.1002-1008
• /
• 2007

Natural convection flows in a doubly-inclined cubical air-filled cavity are numerically simulated by a solution code(PowerCFD) using unstructured cell-centered method. For a physical realizability, the cavity has one pair of opposing isothermal faces at different temperatures, $T_h\;and\;T_c$, respectively, the remaining four faces having a linear variation from $T_c\;to\;T_h$. The paper redefines a new doubly-inclined orientation for the cubical-cavity benchmark problem. Special attention is paid to three-dimensional thermal characteristics in natural convection according to the new orientation at $Ra=4\times10^4$. Comparisons of the average Nusselt number at the cold face are made with benchmark solutions and experimental results found in the literature. It is found that the average Nusselt number at the cold face has a maximum value at the doubly-inclined angle ranging from $40^{\circ}\;to\; 45^{\circ}$ We also report the effect of new orientation on the type of temperature structure in a doubly-inclined cubical-cavity.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2053-2058
• /
• 2008

It was investigated thermal performances on two array types of a serial circulation and a two-way parallel circulation for six water-cooled cold plates covered with non-metallic material (polycarbonate, PC) to reduce weight of the cooling devices for humanoid robot cooling. Six cold plates attached on $10{\times}10\;mm^2$ copper base : $0.5{\times}0.5\;mm^2$ pin-finned surfaces of 1.5 mm high with 0.5 mm array spacing, was mounted on six copper heating blocks with isothermal conditions of $50{\sim}90^{\circ}C$, respectively. In order to compare thermal characteristics according to two circulation types, the surface temperatures of heating blocks and the cooling water temperatures at inlets and outlets of cold plates were measured. From the results, it was found that a two-way parallel circulation was better performance than a serial circulation in terms of total thermal resistance, total heat transfer rate, and surface temperature rises from $1^{st}$ heating block to last one for six multiple cold plates.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.22 no.9
• /
• pp.614-619
• /
• 2010

Recently, a problem related to the thermal management in portable electronic and telecommunication devices is becoming issued. That is due to the trend of a slimness of the devices, so it is not easy to find the optimal thermal management solution for the devices. From now on, a pressed circular type cooling device has been mainly used, however the cooling device with thin thickness is becoming needed by the inner space constraint of the applications. In the present study, the silicon flat plate type cooling device with the separated vapor and liquid flow path was designed and fabricated. The normal isothermal characteristics created by vapor-liquid phase change was confirmed through the experimental study. The cooling device with 70 mm of total length showed 6.8 W of the heat transfer rate within the range of $4{\sim}5^{\circ}C/W$ of thermal resistance. In the future, it will be possible to develop the commercialized cooling device by revising the fabrication process and enhancing the thermal performance of the silicon and glass cooling device.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.6
• /
• pp.1381-1389
• /
• 1988

The heat transfer by simultaneous conduction, convection and radiation between flame and fuel surface in a thermally radiating medium is investigated theoretically. The flame and fuel surface are assumed to be diffuse, gray, infinite, isothermal, parallel surfaces separated by a finite distance. The space between the plates is supposed is formulated exactly in terms of simultaneous interior-differential equations. The numerical results reveal the effect of the system parameters on the heat transfer characteristics and the temperature distributions. The numerical results reveal that the optically thick radiating medium has a blocking effect on the total beat transfer. The temperature distributions are observed to be convex upward for an optically thick radiating medium as the alberto decreases.

• Transactions on Electrical and Electronic Materials
• /
• v.1 no.2
• /
• pp.7-11
• /
• 2000

a-Si:H and poly-Si TFT(thin film transistor) characteristics were investigated using an inverted staggered type TFT. The TFT an as-grown a-Si:H exhibited a low field effect mobility, transconductance, and high gate threshold voltage. The poly-Si films were achieved by using an isothermal and RTA treatment for glow discharge deposited a-Si:H films. The a-Si:H films were cystallized at the various temperature from 600$^{\circ}C$ to 1000$^{\circ}C$. As anneal temperature was elevated, the TFT exhibited increased g$\sub$m/ and reduced V$\sub$ds/. V$\sub$T/. The poly-Si grain boundary passivation with grain boundary trap types and activation energies as a function of anneal temperature. The poly-si TFT showed an improved I$\sub$nm//I$\sub$off/ ratio of 10$\^$6/, reduced gate threshold voltage, and increased field effect mobility by three orders.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.2
• /
• pp.87-97
• /
• 2013

Recently the use of gas spring in the combat and commercial vehicle's suspension is increasing. Because of its nonlinear characteristics, the gas spring can support wide range of dynamic loads and gives good ride quality. In design of gas spring, isothermal and adiabatic processes are applied generally, but those processes could not produce heat transfer effect in the simulation. So in this study, heat transfer differential equation and BWR/Ideal state equation are used to calculate the pressure of gas spring which is changing with time. The numerical analysis showed that the pressure of gas spring forms a hysteresis loop in the both of the state equations. But the peak pressure value of BWR equation over 0.1Hz frequency are higher than that of adiabatic process. And the test results showed that the differences between test results and ideal gas equation are smaller than those of BWR equation, so the ideal equation is more accurate than BWR equation in this case.

• Journal of Korea Foundry Society
• /
• v.28 no.3
• /
• pp.129-135
• /
• 2008

The reheating stage of electromagnetically stirred Al billet is a critical factor in the thixoforming process. When reheated to the solid-liquid state, the microstructure evolves to a more globular and more homogeneous structure by a coarsening mechanism, the kinetics depending on the initial microstructure. Microstructural evolution has been characterized by conventional parameters (mean size of particle and shape factor) as a function of holding time in the solid-liquid state. The aim of this study is to report experimental results concerning microstructural evolution in the solid-liquid state of electromagnetically stirred Al billet. The material was elaborated in the form of continuously cast bars solidified with electromagnetic stirring to degenerate the dendritic structure. The choice of the reheating conditions is determined by a dendritic ripening and coalescence mechanism, involving variations of both the shape and size of the particles. The reheating time has to be long enough to allow a minimum degree of spheroidizing, but has to be limited as much as possible in order to avoid excessive ripening. The optimum microstructure was obtained at the reheating temperature of near $584^{\circ}C$ and the holding time of 5 min. The only means of combining high productivity with good casting quality was to use feedstock billets whose microstructure showed rapid transformation characteristics.

• Journal of Power System Engineering
• /
• v.17 no.4
• /
• pp.109-114
• /
• 2013

In this study, the microstructure, mechanical properties and high temperature oxidation characteristics of HiSiMo and HiSiMoM ductile iron for exhaust manifold were investigated. The HiSiMoM ductile iron was developed by optimization of alloying element addition and casting design. The exhaust manifold prototype was fabricated using the HiSiMoM iron and this resulted in the weight saving of 0.73kg. The microstructures of the HiSiMo and HiSiMoM irons were similar each other and graphite nodularity was 89% and 93% respectively. Tensile strengths of them were 663.5 and 674.4 MPa and Brinell hardness were 235.3 and 243.9 respectively. Both irons showed parabolic weight gain behavior in high temperature oxidation atmosphere. Oxidation layer was divided into external and internal layers. The weight gain of the HiSiMoM iron was lower than that of the HiSiMo iron after isothermal oxidation test at $900^{\circ}C$. This should be rationalized by higher Si enrichment at the interface of the matrix and internal layer of the HiSiMoM iron.