• Preventive Nutrition and Food Science
• /
• v.10 no.1
• /
• pp.17-21
• /
• 2005

This study was carried out to determine whether detection of minerals separated from irradiated mussel could be could be done by thermoluminescence (TL) method. After the minerals were separated by sodium polytungstate solution (2.0 g/mL) from irradiated mussel, organic compounds remaining in the minerals were removed by acid-base treatment and dried at 50℃ overnight, and then the minerals were measured through TL. The TL intensities of separated minerals at different irradiation doses during storage conditions of room and darkroom were obtained. TL intensity of first glow curves for minerals separated from irradiated mussel showed linear increase from the control to 5 kGy and slight increase from 5 kGy to 10 kGy. Since glow curve ratios of G2, G3 and G4, calculated from re-irradiated minerals measured immediately after irradiation and after storage of three months were over 0.5, detection of irradiation was possible. G1, which showed the glow curve ratios above 0.1, was classified as non-irradiated samples because the unique first glow curve was not found within the recommended temperature interval (150-230℃). Hence, on the basis of TL intensity, and glow curve ratio and shape, it is possible to correctly identify irradaited mussels after mineral separation during storage.

• Preventive Nutrition and Food Science
• /
• v.3 no.1
• /
• pp.22-26
• /
• 1998

Model food containing common salt(NaCl) was subjected to the thermoluminescene(TL) detection whether it is irradiated or not. Salt irradiated with $^60Co$-gamma ray and electron beam exhibited a characteristic TL gowcurve depending on the irradiation dose, showing major peaks at $206^{\circ}C$ and $326^{\circ}C$. The intensity of TL glowcurves was directly proportional to the irradiated doses regardless of irradiation sources at each concentration of salt. A high correlation coefficient was observed for irradiated salt between the irradiation doses and the corresponding TL responses. At the same dose, the intensity of TL glowcurve increased as the concentration of salt increased in the test sample. TL glowcurves of nonirradiated salt and irradiated model food without salt were negligible and similar to a baseline . However, irradiated model food containing salt gave rise to a characteristic TL glowcurve with two major peaks at about $240^{\circ}C$ and $300^{\circ}C$, respectively. The results showed that salt played a role as an internla as well as external indicator in TL measurements, indicating that TL will be applicable to other condiments and spices with salt for their detection whether they are irradiated or not.

• Journal of the Korean Solar Energy Society
• /
• v.38 no.3
• /
• pp.1-20
• /
• 2018

It is a very important and fundamental process to know accurately the intensity of the solar energy coming into the installed module considering the tilted angle. Europe and the US commonly use a program called PVsyst to convert the global horizontal irradiation to global irradiation on tilted plane. There are two types of models that PVsyst uses to convert to irradiation on tilted plane. In this paper, Perez model, which is a decomposition model and Perez model, which is a transposition model used in PVsyst, are applied based on global horizontal irradiation and global irradiation on tilted plane measured in a specific area. The comparison of the decomposition model shows the effect of the transpostion model on global irradiation on tilted plane conversion by comparing the ratio of the horizontal diffuse irradiation amount of the Watanabe model which are highly trusted in Asia and the Perez model. The comparison of transposition model confirm the error between the measured data and the calculated value which is applied Perez model to global horizontal irradiation decomposed by Perez model and Watanabe model. Based on the two comparisons, This paper propose a method to confirm the reliability of transposition model and reduce the error when PVsyst is used in Korea.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.4
• /
• pp.543-545
• /
• 2006

Surface photovoltage (SPV) measurements were performed to investigate the optic-electrical properties in the electron beam irradiation semi-insulating GaAs (e-beam irradiation SI-GaAs) and semi-insulating GaAs (SI-GaAs). The signal intensity showed stronge. dependency on the frequency in the SI-GaAs than it did in the e-beam irradiation SI-GaAs. This result indicates that the number of the generated photo-carriers depends on the surface state. Also, the B region of the e-beam irradiation SI-GaAs found a weak signal. This result was explained by the surface and internal damage with e-beam irradiation.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.27 no.1
• /
• pp.63-68
• /
• 1998

Irradiation can be utilized to inhibit sprouting of onions and garlic. Thermoluminescence(TL) is a potential method to detect post-irradiation of onions and garlic because they are irradiated with soil or dusts on them, from which minerals can be isolated for TL analysis. This study was to determine whether TL can be applied for the detection of post-irradiation of onions and garlic. Onions and garlic produced in Korea were irradiated in the range of 0.01~0.6kGy. Minerals isolated from the samples using sodium polytrungstate solution were used for TL analysis. The onions and garlic irradiated at 0.15kGy or higher could be detected with little errors. Minimum dose for the 2nd glow could be applied since the dose for the 2nd glow did not affect the results. The TL intensities of the temperature ranges of 229~295$^{\circ}C$ and 229~361$^{\circ}C$ and the maximum intensity provided more accurate information for the determination of the post-irradiation of onions and garlic.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.12
• /
• pp.1087-1092
• /
• 2007

We developed the 4-channel Light Medical Therapy Apparatus for Skin Injury Cure using a high brightness LED. This equipment was fabricated using a micro-controller and a high brightness LED, and designed to enable us to control light irradiation time, intensity and reservation. In this paper, the designed device was used to find out how high brightness LED light affects the skin injury of SD-Rat(Sprague-Dawley Rat). In the experiment, $1\;cm^2$ wounds on the skin injury of SD-Rat(Sprague-Dawley Rat) were made. Light irradiation group and none light irradiation group divided, each group was irradiated one hour a day for 14 days. In result, compared with none light irradiation group, the lower incidence of inflammation and faster recovery was shown in light irradiation group.

• Journal of the Korean Society of Radiology
• /
• v.6 no.5
• /
• pp.351-356
• /
• 2012

Ultrasonic cavitation is a physical phenomenon that generates and collapses microbubbles in media (mainly fluids) under conditions of strong ultrasonic irradiation. In this study, changes in the ultrasonic acoustic characteristics of bubble clouds in relation to ultrasonic irradiation were observed by the quantitative evaluation of cavitation yields. Concave-type single ultrasonic transducers with center frequencies of 500 kHz and 1.1 MHz were used to produce cavitation, and 2.25 MHz interference ultrasonic waves that would traverse any bubble clouds generated were used to analyze the cavitation. The parameters used for the evaluation of cavitation yields (changes in the center frequency, attenuation characteristics, and the propagation time of penetrating waves) were analyzed in relation to the cavitation-generating conditions (irradiation intensity, excitation signal, and center frequency). On the basis of these results, correlations between the changes in the center frequency and irradiation intensity were identified. Although the correlation coefficient was low, notable changes were observed in the center frequency under certain irradiation conditions. Attenuation trends in the interference ultrasonic waves showed high correlations with all the irradiation conditions, and it was noted that these trends were not affected by the forms of cavitation generated. No differences in the propagation time were observed among different irradiation conditions. These findings suggest that bubble yields can be quantitatively evaluated effectively by evaluating the diverse irradiation conditions and that such a quantitative evaluation could be used to study the basic cavitation phenomenon occurring in high-intensity ultrasonic wave treatment.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.24 no.1
• /
• pp.301-312
• /
• 1997

The purpose of this study was to evaluate the analgesic effect on pulp induced by pulsed Nd : YAG laser according to the power density, irradiated time and the method of application (Non-contact vs contact) in vivo. Experiments were carried out on 90 volunteers who have sound 4 canines. Each canine was grouped by the intensity and the time of irradiation of pulsed Nd : YAG laser was measured. Mean EPT response(units) was measured at 5 min, 30 min, and 60 min after irradiation with various intensity(1.5-3W, 15-30Hz), irradiated time (1.5min, 3min), and application method (Non-contact and contact). The results were as follows: 1. 5 minutes after irradiation, the mean EPT response(units) was increased by 32 % in the non-contact method and by 35% in the contact method of application. Which showed significant difference in mean EPT response(units) compared to not-lased canine in each groups(P<0.05). 2. The mean EPT response(units) with irradiating condition according to the various laser intensity, and the irradiation time stastically did not show significant difference in each groups as time elapsed. 3. There was no significant difference between the non-contact and contact method in the mean EPT response(units). 4. The mean EPT response(units) returned to the baseline value within 30 miuntes. In regard to the above results, the analgesic effect on pulp induced by pulsed Nd : YAG laser resulted a slight increase of pulpal pain threshold, but it was not as high as to replace the role of drug analgesia as whole. This technique can be used for inducing pulpal analgesia as adjunct to other pain control methods and is needed to develop better analgesic effects.

• Applied Science and Convergence Technology
• /
• v.23 no.5
• /
• pp.201-210
• /
• 2014

The influence of electron irradiation and hydrogen adsorption on the electronic structure of the $SrTiO_3$ (001) surface was investigated by ultraviolet photoemission spectroscopy (UPS). Upon electron irradiation of the surface, UPS revealed an electronic state within the band gap (in-gap state: IGS) with the surface kept at $1{\times}1$. This is considered to originate from oxygen vacancies at the topmost surface formed by electron-stimulated desorption of oxygen. Electron irradiation also caused a downward shift of the valence band maximum indicating downward band-bending and formation of a conductive layer on the surface. With oxygen dosage on the electron-irradiated surface, on the other hand, the IGS intensity was decreased along with upward band-bending, which points to disappearance of the conductive layer. The results indicate that electron irradiation and oxygen dosage allow us to control the surface electronic structure between semiconducting (nearly-vacancy free: NVF) and metallic (oxygen de cient: OD) regimes by changing the density of the oxygen vacancy. When the NVF surface was exposed to atomic hydrogen, in-gap states were induced along with downward band bending. The hydrogen saturation coverage was evaluated to be $3.1{\pm}0.8{\times}10^{14}cm^{-2}$ with nuclear reaction analysis. From the IGS intensity and H coverage, we argue that H is positively charged as $H^{{\sim}0:3+}$ on the NVF surface. On the OD surface, on the other hand, the IGS intensity due to oxygen vacancies was found to decrease to half the initial value with molecular hydrogen dosage. H is expected to be negatively charged as $H^-$ on the OD surface by occupying the oxygen vacancy site.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.4
• /
• pp.208-210
• /
• 2013

ZnO films were deposited on glass substrates by radio frequency (RF) magnetron sputtering and exposed to intense electron beam irradiation to investigate the effects of electron irradiation on the properties of the films. Although all of the films had ZnO (002) textured structure regardless of electron irradiation, the grain sizes of the films decreased with electron irradiation. Surface roughness also depended on electron irradiation. The surface roughness varied between 2.3 and 1.6 nm, depending on the irradiation energy. Based on photoluminescence (PL) characterization, the most intense UV emission was observed from ZnO films irradiated at 900 eV. Since the intensity of UV emission is dependent upon the stoichiometric of ZnO films, we conclude that 900 eV was the optimum electron irradiation energy to achieve the best stoichiometric of ZnO films in this study.