• 한국환경보건학회지
• /
• 제38권6호
• /
• pp.568-574
• /
• 2012

Objectives: The purpose of this experiment is to understand the phosphorus removal ratio effects of iron plates per unit of surface area through the iron electrolysis system, which consists of an anoxic basin, aerobic basin, and iron precipitation apparatus. Methods: Iron electrolysis, which uses an iron precipitation reactor in anoxic and oxic basins, consisted of iron plates with total areas of 400 $cm^2$, 300 $cm^2$ and 200 $cm^2$ respectively. The FNR process was operated with a hydraulic retention time and a sludge retention time of 12 hours and three days, respectively. Wastewater used in the experiments was prepared by dissolving $KH_2PO_4$ in influent water. Results: The iron plates 400 $cm^2$ (16.6 $mA/cm^2$), 300 $cm^2$ (13.3 $mA/cm^2$) and 200 $cm^2$ (7.3 $mA/cm^2$) in surface area in the phosphorus reactor had respective phosphorus of 2.4 mg/l, 2.7 mg/l and 3.2 mg/l in the effluent and phosphorus removal respective efficiencies of 90.3%, 89.1% and 87.1%. The effluent in the reactor, where the iron plate was not used, had relatively very low phosphorus removal efficiency showing phosphorus concentration of 15.3 mg/l and a phosphorus removal efficiency about 38.3%. Phosphorus removal per ferrous was 0.472 mgP/mgFe in the iron electrolysis system where the surface area of iron was low. Phosphorus pollution load per active surface area and the phosphorus removal efficiency had an interrelation of RE = -0.27LS + 89.0 (r = 0.85). Conclusion: With larger iron plate surface area, the elution of iron concentration and phosphorus removal efficiency was higher. The removal efficiency of phosphorus has decreased by increasing the initial phosphate concentration in the iron electrodes. This shows a tendency of decreasing phosphorus removal efficiency because of decreasing of iron deposition as the phosphorus pollution load per active surface area increases.

• 한국주조공학회지
• /
• 제17권2호
• /
• pp.135-144
• /
• 1997

The relative machinability of the invar-type cast alloys, such as invar cast steel, invar-type cast iron, Meehanite cast iron, and the modified Invar-type cast iron containing Mo and V was evaluated based on the tool life test, the surface roughness test and the chipping test. Tool life and surface roughness were measured under various cutting conditions. The tool lives of Invar cast steel, Meehanite cast iron, the modified Invar cast iron and Invar cast iron was 12 min, 8 min, 1 min, 41 min, respectively. The surface finish of Invar cast steel and the modified Invar cast iron was better than that of Meehanite cast non, and the chip breakability of invar cast iron and Meehanite cast iron was better than that of invar cast steel. The Taylor's equations of invar cast steel and the modified invar cast iron were $VT^{0.3076}=154.479$ and $VT^{0.3880}=102.326$, respectively. As the cutting speed increases, the surface finish of the modified invar cast iron was improved.

• 한국전기전자재료학회논문지
• /
• 제26권6호
• /
• pp.478-481
• /
• 2013

Diameter controlled carbon nanotubes (CNTs) were grown using surface modified iron nano-particle catalysts with aminpropyltriethoxysilane (APS). Iron nano-particles were synthesized by thermal decomposition of iron pentacarbonyl-oleic acid complex. Subsequently, APS modification was done using the iron nano-particles synthesized. Agglomeration of the iron nano-particles during the CNT growth process was effectively prevented by the surface modification of nano-particles with the APS. APS plays as a linker material between Fe nano-particles and $SiO_2$ substrate resulting in blocking the migration of nano-particles. APS also formed siliceous material covering the iron nano-particles that prevented the agglomeration of iron nano-particles at the early stages of the CNT growth. Therefore we could obtain the diameter controlled CNTs by blocking agglomeration of the iron nano-particles.

• 한국표면공학회지
• /
• 제32권3호
• /
• pp.393-400
• /
• 1999

The surface characteristics of nitrogen ion implanted iron aluminides were investigated using various electrochemical methods in $H_2$$SO_4$+KSCN and HCl solutions. Nitrogen ion implantation was performed with doses of $3.0$\times$10^{17}$ /ions/$\textrm{cm}^2$ at an energy of 150keV. Nitrogen ion implanted iron aluminides increased the corrosion potential and significantly decreased grain boundary activation, the active current density, and passive current density. Nitrogen implanted iron aluminides with Mo increased the corrosion, pitting potential, repassivation potential and │$E_{pit}$-$E_{corr}$│ value. Whereas, implanted iron aluminides containing boron reduced the pitting and repassivation potential in comparison with nitrogen implanted iron aluminides with Cr and Mo.o.

• 한국광물학회지
• /
• 제17권1호
• /
• pp.75-83
• /
• 2004

석조문화재 표면에 형성된 흑화 부위는 미적인 면에서뿐만 아니라 문화재 자체에도 손상을 끼치기 때문에 많은 문제가 되고 있다. 이러한 흑화 부위는 종종 많은 량의 철화합물을 함유하고 있어서, 다른 요소들과 함께 철화합물도 암석 표면의 흑화 현상에 영향을 끼치는 것으로 추정되고 있다. 독일 베를린 시에 있는 석조문화재(Museumsinsel) 내의 표면에서 시료를 채취한 후 함유 철의 이온상태와 화학성분을 결정하기 위하여 뫼스바우어 분광분석법을 사용하였다. 사용된 암석의 원상태와 흑화 부위의 분말시료에 대한 광물학적 및 화학적 분석을 선회절법과 X-선형광법으로 각각 시행하였다. 형성된 철 성분의 기원은 흑화 부위의 제거 등 석조문화재의 보존처리에 중요한 단서를 제공하기 때문에, 철을 다량 함유하고 있는 적색 사암에서 형성된 흑화 부위와 매우 소량 함유하고 있는 백색사암의 표면에 형성된 흑화 부위를 비교하였다. 연구 결과 백색사암 흑화 부위에서는 주변 환경물질에서 기인한 철 성분이, 적색사암 흑색부위에서는 원암에서 보여지는 철 성분이 주성분으로 추정되었다. 적색사암에 있어서는 흑화부위를 제거한 이후에라도 흑화의 주원인인 철 성분이 계속해서 모암의 내부로부터 표면으로 이동될 수 있기 때문에, 제거 이외의 보존처리법이 더 연구되어야한다.

• 대한기계학회논문집A
• /
• 제21권9호
• /
• pp.1491-1497
• /
• 1997

The purpose of this research is to improve the surface roughness of cast-iron pipe porduced by the centrifugal casting. A twin-fluid atomizer of mold-wash slurry is designed for this project. New atomizer is equipped with the existing manufacturing facility to produce pipes. Cast-iron pipes (.cent.125*L3000mm) are produced and the surface roughnesses of those are analysed by UBM. The average surface roughness of new products is 6.7.mu.m while the old products of sand-resin coating method have 17.0.mu.m of average surface roughness. The surface roughness of cast-iron pipe is improved very much than before.

• Journal of the Korean Wood Science and Technology
• /
• 제49권1호
• /
• pp.82-92
• /
• 2021

Nakdong technique is an unfamiliar scorching treatment using an iron heated in a kiln over 1000℃. It is a typical convention in Asian countries to treat Nakdong on the surface of paulownia species. The scorching treatment changes the surface characteristics as well as the color of the wood. This study focused on the effects of functional features such as water resistance, anti-mold, anti-termite, and sound improvement because this treatment is usually used on paulownia wood-bodied musical instruments surface. It took 28'57" for Nakdong-iron treated surface to absorb a droplet of water. The absorbance time of iron treated surface was longer than that of torch treated one. There was no noticeable effect on the anti-mold test. On the anti-termite test, there was nearly 3% more mean mass loss on the torch samples than controlled and iron treated ones. In examining the sound radiation coefficient before and after Nakdong treatment, the Nakdong-iron treated surface showed an increase in the average value of 1.2 m4/kg s, which means that it has sound quality improvement. Through this research, the Nakdong technique results are expected to be used as basic-data for further research and give a practical idea for using the traditional treatment method on the wood surface.

• 한국표면공학회지
• /
• 제38권4호
• /
• pp.156-162
• /
• 2005

Nickel-iron nanocrystalline alloys with different compositions and grain sizes were fabricated by electro-plating for MEMS devices. The iron content of the deposits was changed by varying the nickel/iron ion ratio in the electrolyte. X-ray diffraction (XRD) analysis was applied for measuring the strength of the texture and grain size of the deposits. The nickel/iron atom ratio of the deposits was analyzed by EDS. The hardness of the alloys was evaluated by Vickers hardness indenter. The internal stress of the deposits was measured by Thin Film Stress Measurement using Stoney's formula. Surface morphology and roughness were investigated by Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM). The results of this study revealed that at a grain size of approximately $17\~24$nm the hardness, internal stress and roughness depend strongly on the iron content. With increasing the iron content, the hardness and internal stress of the deposits increased. An excellent correlation between the increase in the internal stress and the loss of (200) texture was found.

• 한국표면공학회지
• /
• 제56권4호
• /
• pp.265-272
• /
• 2023

Photoelectrochemical (PEC) water splitting is one of the promising methods for hydrogen production by solar energy. Iron oxide has been effectively investigated as a photoelectrode material for PEC water splitting due to its intrinsic property such as short minority carrier diffusion length. However, iron oxide has a low PEC efficiency owing to a high recombination rate between photoexcited electrons and holes. In this study, we synthesized nanoporous structured iron oxide by anodization to overcome the drawbacks and to increase surface area. The anodized iron oxide was annealed in Ar atmosphere with different purging times. In conclusion, the highest current density of 0.032 mA/cm² at 1.23 V vs. RHE was obtained with 60 s of pursing for iron oxide(Fe-60), which was 3 times higher in photocurrent density compared to iron oxide annealed with 600 s of pursing(Fe-600). The resistances and donor densities were also evaluated for all the anodized iron oxide by electrochemical impedance spectra and Mott-Schottky plot analysis.

• 공업화학
• /
• 제8권5호
• /
• pp.830-836
• /
• 1997

본 실험에서는 물유리를 사용하여 산세척에 의하여 제조된 산화철 입자의 표면개질에 대하여 연구하였다. 사용한 물유리의 $SiO_2$와 $Na_2O$의 몰비($SiO_2/Na_2O$)는 1, 2, 3.5이였다. 첨가되는 실리카의 양과 pH에 따라 산화철 현탁액의 분산성을 입자의 표면하전과 침강속도에 의하여 평가하였다. 그리고, 중성 영역에서 산화철 입자의 분산안정성을 유지할 수 있는 표면개질제(실리카)의 양을 도출하였으며, 물유리에 의한 산화철 입자의 표면개질을 습식 볼밀링에 의하여 슬러리 상태에서 실시하였다. 그 결과, 표면처리한 산화철 현탁액의 분산 안정성은 실리카의 양과 pH에 상호 의존하였다. 미처리한 산화철은 등전점인 pH 8에서 분산안정성을 잃고 있었으나, 산화철에 대하여 약 0.8wt%의 실리카로 표면처리한 산화철은 pH 5 이상 중성영역에서 분산안정성을 나타내었으며, 음이온성 계면활성제를 0.2wt% 이상 첨가에 의한 분산안정성이 더욱 증가되었다.