• Journal of the Korea Concrete Institute
• /
• v.17 no.1 s.85
• /
• pp.77-84
• /
• 2005

The steel slag, a by-product which is produced by refining pig iron during the manufacture of steel, is mainly used as road materials after aging. It is necessary to age steel slag for long time in air because the reaction with water and free-CaO in steel slag could make the expansion of volume. This problem prevents steel slag from being used as aggregate for concrete. However, steel slag used in this study was controled by a air-jet method which rapidly cools substance melted at a high temperature. The rapidly-chilled method would prevent from generation of free-CaO in steel slag. This study dealt with the influence of the using rate of rapidly-chilled steel slag on flow, dosage of SP, W/C ratio, and strength of mortar by statistical experimental design. Also, the results of this experiment were approved by statistical analysis methods, such as analysis of variance and F-testing. As results of F-testing, this paper proved at $1\%$ level of significance that the more the using rate of rapidly-chilled steel slag increased, the more this affected the enhancement of flow, the decrease of dosage of SP and W/C ratio, and the development of compressive strength. Also, considering the fluidity and compressive strength of mortar, it is desirable to use $75\%$ of rapidly-chilled steel slag for river sand.

• Korean Journal of Poultry Science
• /
• v.30 no.1
• /
• pp.11-16
• /
• 2003

This study was conducted to investigate chemical and sensory characteristics of boiled soup extracted from crossbred ogol chicken as affected by the level of Flavourzyme produced from Aspergillus oryzae and composed with endo-proteinase(674U/g) and exoproteinase(8,053U/g). It was hydrolyzed by different concentrations of the protease enzyme (Flavourzyme)(0%(Control), 0.01％(T$_2$), 0.1%(T$_3$) and 0.5%(T$_4$)) at 45$^{\circ}C$ for 4hrs. Manufacture of the extract was performed by boiling treated meats with medicinal herbs(Sipchun daebo) at a higher pressure condition. Minerals, free amino acid content, sensory properties of the extract were as follows. The sodium contents were increased as the treatment levels of enzyme increased. The iron contents were lowest when the enzyme treated by 0.5% level, however there were not significantly different among the treatments. The copper and mangan contents had no significantly different among the enzyme treatment levels. Higher contents of fee amino acid were observed as the amount of the protease increased with the treatment of higher than 0.1％ enzyme, no significant effect was observed. In sensory properties, the extract manufactured by addition of 0.01∼0.1% of Flavourzyme resulted in a similar or better appearance, flavor, taste and overall palatabilitycompared to control(no enzyme treatment). However, the extract manufactured with 0.5% of Flavourzyme resulted in lower scores in appearance, flavor, taste and overall palatability than the control. In addition, this product showed more off-flavor than control.

• Korean Journal of Materials Research
• /
• v.8 no.11
• /
• pp.1026-1030
• /
• 1998

Thermal properties of Fe- base amorpous alloys were investigated. $Fe_{80}P_6C_{12}B_{12}$ and $Fe_{73}P_{11}C_6B_4AI_4Ge_2$ amorphous alloys were fabricated by melt spinning method and thermal analysis was done by differential scanning calorimeter. After isothermal crystallization. the Avrami exponents of $Fe_{80}P_6C_{12}B_{12}$ and $Fe_{73}P_{11}C_6B_4AI_4Ge_2$ amorphous alloys were 1.8-2.2 and 2.5-4.0, respectively. It means the former alloy shows diffusion controlled growth and the latter one shows interface controlled growth. For $Fe_{80}P_6C_{12}B_{12}$ and $Fe_{73}P_{11}C_6B_4AI_4Ge_2$ amorphous alloys. the activation energies of isothermal crystallization was 353 and 371kJlmol. Also the activation energies of nucleation and growth were 301, 324kJlmol and 273. 30lkJ/mol, respectively. Thus $Fe_{73}P_{11}C_6B_4AI_4Ge_2$ amorphous alloy is considered to be more stable than $Fe_{73}P_{11}C_6B_4AI_4Ge_2$ amorphous alloy.

• Resources Recycling
• /
• v.12 no.4
• /
• pp.20-29
• /
• 2003

In order to efficiently recycle the waste solution resulting from shadow mask processing, nano-sized Ni-ferrite powder was fab-ricated through spray pyrolysis process. The average particle size of the powder was below 100nm. In this study, the effects of the reaction temperature. the concentration of raw material solution and the injection speed of solution on the properties of powder were respectively investigated. As the reaction temperature increased from $800^{\circ}C$ to $1100^{\circ}C$, average particle size of the powder significantly Increased and power structure became more solid, whereat its specific surface area was greatly reduced. Formation rate and crystallization of($NiFe_2$$O_4$) phale increased along with the temperature rise. As the concentrations of iron and nickel components in wastere solution increased, particle size of the powder became larger, particle size distribution became more irregular, and specific surface area was reduced. Formation rate and crystallization of $NiFe_2$$O_4$ phase increased significantly along with the increase of the concentration of solution. As the inlet speed of solution increased, particle size of the powder became larger, particle size distribution became wider, specific surface area was reduced and powder structure became less solid. As the inlet speed of solution decreased, formation rate and crystallization of $NiFe_2$$O_4$ phase significantly increased.

• Membrane Journal
• /
• v.22 no.6
• /
• pp.461-469
• /
• 2012

This study was carried out to find the optimum chemical cleaning (CIP) conditions for ceramic microfiltration membrane process of Y drinking water treatment plant. B train consists of coagulation as pretreatment process with membrane was chemically cleaned 9 times more than that of A train with ozonation and coagulation. The frequent CIP of B train was due to improper CIP method suggested by membrane manufacture as well as different membrane fouling between A and B train resulting from the different pretreatment processes. That is, recovery rate of CIP was overestimated because the rate was calculated based on normalized trans membrane pressure (TMP) rather than normalized permeability. And also, iron oxide fouling was ineffectively removed by citric acid. By using a mixture of 1% citric acid and 0.1 N sulfuric acid as reagent for acid CIP step, the recovery rate of CIP was the highest while CIP efficiency by 0.1 N sulfuric acid was the lowest. When sulfuric acid concentration increased from 0.1 N to 0.3 N in mixture, total recovery rate of CIP was not increased due to the decreased CIP efficiency in alkali CIP step by 0.3% NaOCl although its rate in acid CIP step was increased. It was proved through the experiment result of CIP sequence changes that an acid followed by alkali CIP was more effective than that of the reverse method.

• Transactions of the Korean hydrogen and new energy society
• /
• v.9 no.4
• /
• pp.161-167
• /
• 1998

It has been investigated the effects of alloying elements and binders on the corrosion behavior of metal hydride electrodes for anode of Ni/MH secondary battery. The $AB_5$-type alloys, $(LM)Ni_{4.49}Co_{0.1}Mn_{0.205}Al_{0.205}$ and $(LM)Ni_{3.6}Co_{0.7}Mn_{0.3}Al_{0.4}$, were used for the experiments. The electrodes were prepared by mixing and cold-pressing of alloy powders with Si sealent or PTFE powders, or cold-pressing the electroless copper coated alloy powders. The amount of copper coating was 20wt%. In order to examine corrosion behavior of the electrodes, the corrosion current and the current density, in 6M KOH aqueous solution after removal of oxygen in the solution, were measured by potentiodynamic and cyclic voltamo methods. The results showed that Co in the alloy increased corrosion resistance of the electrode whereas Ni decreased the stability of the electrode during the charge-discharge cycles. The electrode used Si sealant as a binder showed a lower corrosion current density than the electrode used PTFE and the electrode used Cu-coated alloy powders showed the best corrosion resistance.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.7
• /
• pp.2719-2726
• /
• 2010

The purpose of this study was to investigate the scientific basic grounds for the assessment of health and environmental diseases resulting from air pollutants in Pohang. For this study, we investigated pollutants, weather characteristics and concentration distribution of fine particles ($PM_10$) yearly and each season, using data from Air Quality Monitoring Stations. The properties of concentration distribution and seasonal fluctuation of $PM_10$ were studied qualitatively and quantitatively using CALPUFF, air dispersion model. The average concentration of $PM_10$ for each season was spring($75.7{\mu}g/m^3$)>summer($56.8{\mu}g/m^3$)>winter($53.6{\mu}g/m^3$)>fall( $52.7{\mu}g/m^3$). In the case of spring, high concentrations appear due to the Asian dust frequently occurring. The contributions of $PM_10$ classified by the types of pollution source in Pohang were point source 62%>mobile source 33%>area source 5%. An important point is that 97% of emissions were produced from the iron manufacture in steel industry. Therefore, it is necessary to control the emission sources of pollutants and to construct an observation system at Pohang steel industrial complex from now on. It’s time to control the risk factors for health and environmental disease to protect the health of resident in Pohang and its neighboring areas.

• Resources Recycling
• /
• v.3 no.3
• /
• pp.32-49
• /
• 1994

Hydration process is one of the basic carbonation system. Limestone sludge produced in Pohang Iron & Steel Co., Ltd. We tested for identify of hydration characteristics. The result obtained in this study can be summarized as follows; 1. The classify of limestone sludge is type of ground calcium carbonate(-3mm+325mesh)and the major mineral of calcite, and further more high grade(CaO 51%), fine powder(15~22$\mu\textrm{m}$). 2. Limestone sludge mixed two process sludge, first one is washing process sludge and the other one is wet collect kiln dust. The composition rate is about 8:2. Wet collect kiln dust is major mineral of calcite, too. But the sludge is assumed to one by quick lime, slaked lime and unreacted natural limestone. So, the ideal process is dividing of the washing process sludge and wet collect kiln dust. 3. We manufactured of slaked lime from limestone sludge. To investigate the effect of hydration reactor, the experiments was done with various reactor type as magnetic stirrer, shaking incubator and ultrasonic vibration reactor, respectively. Generally, ultrasonic vibration reactor is excellent hydration for limestone sludge and produced very fine slaked lime powder with ideal distribution. 4. The optimum condition is 10% pulp density, when the manufacture of fine slaked lime powder by ultrasonic vibration reactor. And hydration times to compare the results of the study with ultrasonic vibration reactor of generalized most short time(5~10 min). 5. Finally, the dispersive characteristics of slaked lime powder measured 1~5 $\mu\textrm{m}$ from limestone sludge were compared with those of natural limestone ones(10~20$\mu\textrm{m}$), in order to check applicability of slaked lime with hydration process from limestone sludge.

• (The) Research of the performance art and culture
• /
• no.39
• /
• pp.133-165
• /
• 2019

This paper tried an approach of oral literature as the research subject of Soeburi song in Ulsan. First, UlsanSoeburi song is meaningful as materials collected in Ulsan such as Hansil, Dodoekgol, Dudong and Byeongueong. In addition, it is related to regional identity as song native to Ulsan, which has prototype and archetype. And it shows that Ulsan is the city as well as hometown of Soeburi(meaning ' iron manufacture'). The characteristics of lyrics are different between Hansil Soeburi song and Dodeokgol Soeburi song. Jeiman Choi is considered as a good oral literature poet, because he is a performer who is faithful in official structural principal and in original lyrics(archetype) of Soeburi song. Therefore, SoeburiBulmei song of Jeiman Choi signifies aesthetic meaning, having lyrics which make to feel labor's purity and sacred and melody which overcomes labor's difficulty through united action. On the other hand, SoeburiBulmei song of Dalo Kim in Doseokgol shows that he is a extemporaneous performer even though he performs based on official structural principal. In this paper, transmission and changes of UlsanSoeburi song are divided into basic type, frequent shift type and overall type. 'Basic type' originates from Jeiman Choi's Soeburi song in Hansil. 'Frequent shift type' was created by combining SoeburiBulmei song of Dalo Kim in Doseokgol and SoeburiGeumjul song in Ulsan. 'Overall type' is current Soeburi song, which was created by adding Bulmei song for lulling a baby in Byeongueong near Dalcheon region and Seoknyanggan(smithy) Bulmei song. UlsanSoeburi song is being passed down continuously, strengthening the identity as a representative folk song in Ulsan through endless process of transmission and changes.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.8
• /
• pp.119-127
• /
• 2006

Granulated Blast Furnace Slag (GBFS) is produced in the manufacture process of pig-iron and shows a similar particle formation to that of natural sea sand and also shows light weight, high shear strength, well permeability, and especially has a latent hydraulic property by which GBFS is solidified with time. Therefore, when GBFS is used as a backfill material of quay or retaining walls, the increase of shear strength induced by the hardening is presumed to reduce the earth pressure and consequently the construction cost of harbor structures decreases. In this study, using the model sand box (50 cm$\times$50 cm$\times$100 cm), the model wall tests were carried out on GBFS and Toyoura standard sand, in which the resultant earth pressure, a wall friction and the earth pressure distribution at the movable wall surface were measured. In the tests, the relative density was set as Dr=25, 55 and 70% and the wall was rotated at the bottom to the active earth pressure side and followed by the passive side. The maximum horizontal displacement at the top of the wall was set as ${\pm}2mm$. By these model test results, it is clarified that the resultant earth pressure obtained by using GBFS is smaller than that of Toyoura sand, especially in the active-earth pressure.