A ZnO nanowire-based FET is fabricated m this study on a flexible substrate of PES. For the flat and bent flexible substrates, the current ($I_D$) versus drain-source bias voltage ($V_{DS}$) and $I_D$ versus gate voltage ($V_G$) results are compared. The flat band was Ion/Ioff ratio of ${\sim}10^7$, a transconductance of 179 nS and a mobility of ~10.104 cm2/Vs at $V_{DS}$ =1 V. Also bent to a radius curvature of 0.15cm and experienced by an approximately strain of 0.77 % are exhibited an Ion/Ioff ratio of ${\sim}10^7$, a transconductance of ~179 nS and a mobility of ${\sim}10.10 cm^2/Vs$ at $V_{DS}$ = 1V. The electrical characteristics of the FET are not changed very much. although the large strain is given on the device m the bent state.
Omega-shaped-gate (OSG) nanowire-based field effect transistors (FETs) have been attracted recently attention due to their highdevice performance expected from theoretical simulations among nanowire-based FETs with other gate geometries. OSG FETs with the channels of ZnO nanowires were successfully fabricated in this study with photolithographic processes. In the OSG FETs fabricated on oxidized Si substrates, the channels of ZnO nanowires with diameters of about 60 nm are coated surroundingly by $Al_{2}O_{3}$ as gate dielectrics with atomic layer deposition. About 80 % of the surfaces of the nanowires coated with $Al_{2}O_{3}$ is covered with gate metal to form OSG FETs. A representative OSG FET fabricated in this study exhibits a mobility of 98.9 $cm^{2}/Vs$, a peak transconductance of 0.4 ${\mu}S$, and an Ion/Ioff ratio of $10^6$ the value of the Ion/Ioff ratio obtained from this OSG FET is the highest among nanowire-based FETs, to our knowledge. Its mobility, peak transconductance, and Ion/Ioff ratio arc remarkably enhanced by 11.5, 32, and $10^6$ times, respectively, compared with a back-gate FET with the same ZnO nanowire channel as utilized in the OSG FET.
Undoped p-type and Te doped n-type GaSb crystals were grown by the vertical Bridgman method. The lattice constant of the GaSb crystals was 6.096.+-.000373.angs.. The carrier concentration, the resistivity, and the carrier mobility measured by the van der Pauw method were p.iden.8*10$^{16}$ c $m^{-3}$ , .rho..iden.0.20 .ohm.-cm, .mu.$_{p}$ .iden.400c $m^{2}$$V^{-1}$ se $c^{-1}$ for p-type, n.iden.1*10$^{17}$ c $m^{-3}$ , .rho..iden.0.15 .ohm.-cm, .mu.$_{n}$ .iden.500c $m^{2}$$V^{-1}$ se $c^{-1}$ for n-type at 300K. In case of treatment with metal ion of R $u^{+3}$, P $t^{+4}$, the carrier concentration, resistivity and carrier mobility of the GaSb crystals were p.iden.2*10$^{17}$ c $m^{-3}$ , .rho..iden.0.08.ohm.-cm, .mu.$_{p}$ .iden.420c $m^{2}$$V^{-1}$ se $c^{-1}$ for p-type, n.iden.2.5*10$^{17}$ c $m^{-3}$ , .rho..iden.0.07.ohm.-cm, .mu.$_{n}$ .iden.520c $m^{2}$$V^{-1}$ se $c^{-1}$ for n-type respectively. GaSb crystals had a tendency to lower resistivity and higher mobility, for surface treatment with metal ion effectively diminished surface recombination centers.s.
사파이어 (0001) 기판의 활성화 이온빔 (RIB) 처리 후 MOCVD에서 성장한 GaN박막의 열처리를 통한 구조 변화를 살펴보고, 전기적 성질의 변화를 관찰하기 위하여 전기로를 이용하여 열처리를 하였다. 시편의 분석을 위하여 DCXRD, Hall, TEM을 사용하였다. 100$0^{\circ}C$에서 시간을 변화시키면서 열처리한 시편에서 DCXRD의 FWHM는 약 50 arc-sec 정도 감소하였고, Hall 이동도는 약 80$\textrm{cm}^2$/V.sec 정도 향상되었다. 가장 좋은 Hall 이동도를 보인 처리된 시편과 처리 전 시편의 TEM 비교 관찰에서 전위 밀도는 56~69% 정도 감소하였고 격자의 변형도 줄어들었다. 이것은 결정의 질과 전기적 성질 사이의 상관관계를 암시하며, 기판의 RIB 처리와 성장 후 적절한 열처리의 조합이 MOCVD로 성장시킨 GaN 박막의 특성을 개선시키는 것을 명확하게 보여준다.
To use polycrystalline Si Thin Film Transistor (poly-Si TFT) in high density SRAM instead of High Load Resistor (HLR), TFT is needed to show good electrical characteristics such as large carrier mobility, low leakage current, high driver current and low subthreshold swing. To satisfy these electrical characteristics, the trap state density must be reduced in the channel poly. Technological issues pertinent to the channel poly fabrication process are investigated and discussed. They are solid phase growth (SPG), Si-ion implantation, laser annealing and hydrogenation. The electrical properties of several CVD oxides used as the gate oxide of TFT are compared. The dependence of the electrical characteristics of TFT on source-drain ion-implantation dose, drain offset length and dopant lateral diffusion are also described.
Ion implantation provides a unique way to modify the mechanical, optical and electrical properties of polymer by depositing the energy of ions in the material on the atomic scale. Implantation of ions into the polymers generally leads to a radiation damage, which, in many cases, modifies the properties of the surface and bulk of the material. These modifications result from the changes of the chemical structure caused in their turn by changing the chemical bonding when the incident ions cut the polymer chains, breaks covalent bonds, promotes cross-linking, and liberates certain volatile species. We studied the relation among the linear energy transfer (LET) and changes of surface microstructure and surface resistivity on PPS material using the high current ion implantation technology The surface resistivity of nitrogen implanted PPS decreased to $10^{7}{\Omega}/cm^{2}$ due to the chain scission, cross linking, ${\pi}$ electron creation and mobility increase. In this case, the surface conductivity depend on the 1-dimensional hopping mechanism.
Lithium-ion batteries have a small volume, light weight and high energy density, maximizing the utilization of mobile devices. It is widely used for various purposes such as electric bicycles and scooters (e-Mobility), mass energy storage (ESS), and electric and hybrid vehicles. To date, lithium-ion batteries have grown to focus on increasing energy density and reducing production costs in line with the required capacity. However, the research and development level of lithium-ion batteries seems to have reached the limit in terms of energy density. In addition, the charging time is an important factor for using lithium-ion batteries. Therefore, it was urgent to develop a high-speed charger to shorten the charging time. In this thesis, a discharger was fabricated to evaluate the capacity and characteristics of Li-ion battery pack which can be used for e-mobility. To achieve this, a smart discharger is designed with a combination of active load, current sensor, and temperature sensor. To carry out this thesis, an active load switching using sensor control circuit, signal processing circuit, and FET was designed and manufactured as hardware with the characteristics of active discharger. And as software for controlling the hardware of the active discharger, a Raspberry Pi control device and a touch screen program were designed. The developed discharger is designed to change the 600W capacity battery in the form of active load.
'이동'이란 사람들이 매 순간 행동하고, 타인과 교류하며 특정 목적을 달성하는 '장소'의 확장 개념으로 이동에 불편함을 느끼는 사회적 교통약자에게 있어 이동보조수단인 휠체어는 신체적·정신적 삶의 질을 향상하는데 아주 큰 영향을 발휘한다. 이러한 휠체어는 수동식 휠체어와 전동식 휠체어로 구분되는데, 수동식 휠체어는 이용자의 팔과 손의 힘으로 앞으로 추진하게 된다. 하지만 전동식 휠체어는 배터리를 통해 모터에 전기에너지를 공급 해 주고, 모터의 회전에 의해 앞으로 추진하게 된다. 전동휠체어는 주로 실외활동을 중점으로 개발되고 있으나 최근에는 일상생활의 주 공간인 실내용 이동보조수단에 대한 개발 요구가 증가하게됨에 따라 실내용 전동휠체어 개발 또한 활발하게 이루어지고 있다. 실내용 이동보조수단의 경우 공간의 특성상 단거리를 반복 주행하므로 본 연구에서는 전동휠체어의 단거리 주행에 따른 리튬이온배터리의 주행특성을 확인하고, 연속주행의 리튬이온배터리 주행특성을 비교분석하였다. 단거리 주행의 경우 리튬이온배터리의 방전종지전압 도달 시 까지 5초 주행 1초 정지를 반복수행하였다. 리튬이온 배터리를 적용한 실내용 전동휠체어의 주행특성을 분석한 결과 실내 이동을 고려한 단거리 주행시험의 경우 연속주행보다 주행시간이 2.8% 짧아진 것을 확인하였다. 실내용 전동휠체어의 회전모터에 인가 된 전류의 경우 실내 이동을 고려한 단거리 주행이 연속주행 보다 15.4% 높게 나타난 것을 확인하였다.
소오스와 드레인 근처에 포켓이온이 주입된 halo구조의 MOSFET에서 전송자의 이동도 감소는 포켓이온주입의 조건에 따라 이온화된 불순물의 증가에 따른 쿨롱(Coulomb) 산란율의 증가에 의한 이동도의 감소량보다 큰 이동도의 감소가 관측될 수 있다. 게이트 바이어스에 대한 이동도의 특성변화도 기존의 일차적인 쿨롱산란의 증가효과에 의한 해석과 비교하여 상이한 결과가 나타날 수 있음이 실험적으로 확인되고 있다. 본 연구에서는 포켓이온 주입에 의하여 쿨롱산란원이 되는 유효불순물 농도의 증가에 따른 일차적인 이동도의 감소효과를 벗어난 이동도 특성을 분석하여 이동도의 감소현상을 일반적으로 설명할 수 있는 개선된 해석적 모델을 제시하였다. 해석적인 결과를 도출하기 위하여 일차원 영역구분의 근사방법을 적용한 결과, 포켓이온 주입에 의하여 포논산란율 및 표면산란율(surface roughness scattering rate)의 증가도 이동도감소에 기여함이 보여 졌다. 채널의 전송자분포가 드레인 전류에 영향을 미치게 되므로 포켓이온에 의해 유발된 전송자분포의 효과를 분석하여 유효이동도가 추가적으로 감소함을 확인하였다.
For an accurate measurement of aerosol particle size distribution using a differential mobility analyser (DMA), a new calculation process, capable of predicting the masses for the various kinds of water cluster ions generated from a bipolar ionizer, was prepared by improving the previous process. The masses for the 5 kinds of positive and negative water cluster ions produced from a SMAC ionizer were predicted by the improved calculation process. The aerosol particle charging ratios calculated by applying the predicted ion masses to particle charging equations were in good accordance with the experimentally measured ones, indicating that the improved calculation process are more reasonable than the previous one in a mass prediction of bipolar water cluster ions.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.