• Ocean Systems Engineering
• /
• v.6 no.3
• /
• pp.265-287
• /
• 2016

The change of the global performance of a turret-moored FPSO (Floating Production Storage Offloading) with DP (Dynamic Positioning) control is simulated, analyzed, and compared for two different internal turret location cases; bow and midship. Both collinear and non-collinear 100-yr GOM (Gulf of Mexico) storm environments and three cases (mooring-only, with DP position control, with DP position+heading control) are considered. The horizontal trajectory, 6DOF (degree of freedom) motions, fairlead mooring and riser tension, and fuel consumptions are compared. The PID (Proportional-Integral-Derivative) controller based on LQR (linear quadratic regulator) theory and the thrust-allocation algorithm which is based on the penalty optimization theory are implemented in the fully-coupled time-domain hull-mooring-riser-DP simulation program. Both in collinear and non-collinear 100-yr WWC (wind-wave-current) environments, the advantage of mid-ship turret is demonstrated by the significant reduction in heave at the turret location due to the minimal coupling with pitch mode, which is beneficial to mooring and riser design. However, in the non-collinear WWC environment, the mid-turret case exhibits unfavorable weathervaning characteristics, which can be reduced by employing DP position and heading controls as demonstrated in the present case studies. The present study also reveals the plausible cause of the failure of mid-turret Gryphon Alpha FPSO in milder environment than its survival condition.

• Journal of the Society of Naval Architects of Korea
• /
• v.50 no.1
• /
• pp.8-13
• /
• 2013

Excessive yaw motion of a turret moored vessel was examined in this paper. The vessel was moored by an internal turret and catenary mooring lines. The experiments were conducted in regular waves. Turret moored vessel can oscillate from side to side or move to one particular direction, and eventually exhibit large yaw motion. The results showed that the excessive yaw occured for specific condition, ratio of wave lengths and vessel length. It was found that turret moored floating vessel was unstable for regular wave period from 14 to 18 sec and excessive yaw occurred to maximum 50 deg. The time series, trajectory, phase plot and qualitative analysis are performed. The analysis showed that the results of experiments agreed with the that of analytic method and the excessive yaw could be predicted by the stability analysis.

• Journal of Ocean Engineering and Technology
• /
• v.29 no.2
• /
• pp.143-153
• /
• 2015

This paper presents the results of an experimental study on the motion of an FPSO (Floating production storage and off-loading) and the characteristics of the mooring systejavascript:confirm_mark('abe', '1');m according to the turret position. Model tests of a turret-moored FPSO were carried out in the Ocean Engineering basin of KRISO. The FPSO was moored using an internal turret and catenary mooring. The models (1/60 scale) that were prepared included the FPSO, turret, and mooring lines. The experiments were conducted in irregular waves and combined environments, with waves, currents, and winds. A time-domain simulation was performed using OrcaFlex. The motion response and mooring line tension from the present calculations were compared with the results of experiments, and the agreement was fairly good. In addition, the results showed that the weathervaning stability was improved when the position of the turret was moved in the bow direction.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.368-371
• /
• 1996

This paper describes a study on the developments of the high power brushless DC(BLDC) servo system for electric gun/turret drive system. The servo control unit including the DSP based digital servo unit, power amplifier, signal conditioning circuit, internal power circuit is designed and implemented for driving the 10hp BLDC servo system. The developed system is applied to the gun/turret drive & stabilization simulator system and the control performance is verfied through the experiments.

• Journal of Ocean Engineering and Technology
• /
• v.28 no.5
• /
• pp.387-395
• /
• 2014

In this paper, a numerical analysis for an internal turret moored vessel located at a 400-m water depth is conducted. The target vessel has an internal turret that is located at the 0.2 Lpp position from the fore-side, with $3{\times}4$ complex mooring lines installed around the turret circumference. To investigate the motion response of the vessel and the structural reliability of the lines, model tests were conducted. The KRISO ocean basin has a water depth of 3.2 m, which represents 192m using a scaling of 1:60. In order to precisely represent the real-scale condition, equivalent mooring lines needed to be designed. Truncated mooring lines were designed to supplement the restriction of the flume's water depth and increase the reliability of the model testing. These truncated mooring lines were composed of two different chains in order to match the pre-tension, simultaneously restoring the curve and variation in the effective line tension. The static similarities were compared using a static pull-out test and free decaying test, and the dynamic similarities were matched via a regular wave test and combined environments test. Consequently, the designed truncated mooring system could represent the prototype mooring system relatively well in the aspects of kinematics and dynamics.

• Journal of the Society of Naval Architects of Korea
• /
• v.53 no.5
• /
• pp.435-446
• /
• 2016

In this study, hydrodynamic and mooring analysis for LNG FSRU moored by an internal turret with 9 mooring lines are numerically performed using commercial softwares, Hydrostar and Ariane. Met-ocean combinations for screening method are taken from wave governed condition(BV Rule Note NR 493) with relative heading between wave and wind between −45° and +45° and relative heading between wind and current between −30° and +30°. Extreme mooring analysis and sensitivity analysis are performed for intact and damaged (=one line missing) conditions and the parameters for sensitivity analysis are wave peak period, peak enhancement factor and line pretension. In the viewpoint of the design tension in mooring line, chain diameter is designed to satisfy safety factor for each conditions. As the chain diameter is increased from 152mm to 171mm, the designtension is reduced while the minimum breaking load is increased.

• Journal of Ocean Engineering and Technology
• /
• v.29 no.3
• /
• pp.231-240
• /
• 2015

FPSO model tests of mooring line failure were carried out in the ocean basin at KRISO. The characteristics of the motions and mooring lines were investigated. The FPSO ship was moored using an internal turret and catenary mooring. The test model was 1/60 scale. The mooring lines were designed to satisfy the characteristics of the original mooring lines using the truncation method. The experiments were conducted under various environments: a safe wave, current and wind condition; single broken mooring line condition; and transient mode condition. The moment of the break was determined based on experimental test results. The results showed that the FPSO behavior and mooring line tensions were acceptable under the failure condition.

• Ocean Systems Engineering
• /
• v.8 no.3
• /
• pp.247-279
• /
• 2018

This study aims to investigate the behavioral characteristics of the LWSCR (lazy-wave steel catenary riser) for a turret-moored FPSO (Floating Production Storage Offloading) by using fully-coupled hull-mooring-riser dynamic simulation program in time domain. In particular, the effects of initial geometric profile on the global performance and structural behavior are investigated in depth to have an insight for optimal design. In this regard, a systematic parametric study with varying the initial curvature of sag and arch bend and initial position of touch down point (TDP) is conducted for 100-yr wind-wave-current (WWC) hurricane condition. The FPSO motions, riser dynamics, constituent structural stress results, accumulated fatigue damage of the LWSCR are presented and analyzed to draw a general trend of the relationship between the LWSCR geometric parameters and the resulting dynamic/structural performance. According to this study, the initial curvature of the sag and arch bend plays an important role in absorbing transferred platform motions, while the position of TDP mainly affects the change of static-stress level.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.9 no.2 s.25
• /
• pp.5-10
• /
• 2006

The heavy thermal load to battle tanks can cause electronic components' malfunction and crew to be put out of action. The thermal load is generated from Internal heat sources such as electronic devices installed in the room as well as extremely hot weather. In this study, heat and flow analysis for the cabin room of a battle tank was performed to deal with this thermal problem. This study presented the validation of simulation results in comparison with those of test, the investigation of optimal flow design for effective cooling in cabin room and finally the evaluation of thermal comforts to crew.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.2
• /
• pp.248-253
• /
• 2023

Most offshore platforms utilize chain mooring systems for position keeping. However, information regarding related design modification processes is scarce in literature. This study focuses on the floating liquefied natural gas (LNG) bunkering terminal (FLBT) as the target of shore platform and analyzes the corresponding initial mooring design and model tests via numerical simulations. Subsequently, based on the modified design conditions, a new mooring system design is proposed. Adjusting the main direction of the mooring line bundle according to the dominant environmental direction is found to significantly reduce the mooring design load. Even turret-moored offshore platforms are exposed to beam sea conditions, leading to high mooring tension due to motions in beam sea conditions. Collinear environmental conditions cannot be considered as design conditions. Mooring design loads occur under complex conditions of wind, waves, and currents in different environmental directions. Therefore, it is essential appropriately assign the roll damping coefficients during mooring analysis because the roll has a significant effect on mooring tension.