• 대한기계학회논문집B
• /
• 제30권12호
• /
• pp.1196-1202
• /
• 2006

A MEMS methanol reformer was fabricated and its performance was evaluated in the present study. Catalytic steam reforming of methanol was selected because the process had been widely applied in macro scale reformers. Conventional Cu/ZnO catalyst that was prepared by co-precipitation method to give the highest coating quality was used. The reactor structure was made by bonding three layers of glass wafers. The internal structure of the wafer was fabricated by the wet-etching process that resulted in a high aspect ratio. The internal surface of the reactor was coated by catalyst and individual wafers were fusion-bonded to form the reactor structure. The internal volume of the microfabricated reactor was $0.3cm^3$ and the reactor produced exhaust gas with hydrogen concentration at 73%. The production rate of hydrogen was 4.16 ml/hr that could generate power of 350 mW in a typical PEM fuel cell.

• 한국수소및신에너지학회논문집
• /
• 제31권5호
• /
• pp.411-418
• /
• 2020

A reformer is a device for producing hydrogen used in fuel cells. Among them, methanol steam reformer uses methanol as fuel, which is present as a liquid at room temperature. It has the advantage of low operating temperature, high energy density, and high hydrogen production. The purpose of this study is to improve the internal flow of the pressure vessel when a bundle of methanol steam reformer in the pressure vessel goes out to a single outlet. An analysis of equilibrium reaction to methanol steam reforming reaction was conducted using Aspen HYSYS^® (Aspen Technology Inc., Bedford, USA), and based on the results, computational analysis was conducted using ANSYS Fluent^® (ANSYS, Inc., Canonsburg, USA). For comparison of the results, the height of the pressure vessel, outlet diameter, and fillet was set as variables, and the optimum geometry was selected by comparing the effects of gravity and the amount of negative pressure.

• International Journal of Internet, Broadcasting and Communication
• /
• 제16권1호
• /
• pp.156-162
• /
• 2024

The purpose of this study was to investigate the muscle activity of internal oblique, rectus femoris, and multifidus according to knee posture and foot bar angle during pilates reformer high flank exercise. Twelve women in their 20s were recruited within six months of their experience as pilates instructors. The subjects performed six types of high flanks according to knee posture and foot bar angle. EMG signals of internal oblique, rectus femoris, and multifidus during exercise were measured and analyzed by integral EMG. The collected data were processed by repeated measures two-way ANOVA. In this paper it shows the following results. First, internal oblique iEMG was not significantly different according to knee posture and foot bar angle. Second, the rectus femoris had an interaction effect according to knee posture and foot bar angle. Third, there was no significant difference in multifidus according to knee posture and foot bar angle. In conclusion, according to the exercise method, the activity of the rectus femoris was the highest in the knee bending and high foot-bar angle high plank exercise, and there was no difference between the internal oblique and multifidus.

• 한국수소및신에너지학회논문집
• /
• 제29권4호
• /
• pp.317-323
• /
• 2018

Solid oxide fuel cell (SOFC) operates at high temperature, therefor has the advantage of higher power generation and using exhaust heat than other fuel cells. In particular, the reforming reaction can be performed inside the SOFC stack to reduce the cooling of the stack and the burden on the reformer reactor. In this study, the reformer structure, operating characteristics, and thermal efficiency were evaluated for the optimization design of a heat exchanger type reformer of a 1 kW SOFC system.

• 대한기계학회논문집B
• /
• 제40권12호
• /
• pp.793-799
• /
• 2016

폐열을 열원으로 사용하는 저온형 개질기는 하이브리드 연료전지 시스템의 효율향상을 위해 사용되고 있다. 저온형 개질기의 경우 저온의 열적상태에서 높은 열전달 효율을 내는 것이 중요하며, 이를 위한 형상 최적화의 과정이 필요하다. 본 연구에서는 제한된 열공급 상황에서 개질기의 형상인자 변화에 따른 온도 및 반응특성을 전산해석을 통하여 알아보고자 하였다. 해석결과 저온형 개질기의 반응이 활발히 일어나는 영역은 온도가 높은 후단에 제한되는 현상을 보여 고온형 개질기와의 차이를 나타내었다. 또한 개질기의 기체공간속도(Gas hourly space velocity, GHSV)를 감소시키거나 열전달 면적을 증대시킴으로써 효율을 향상 시킬 수 있음을 확인하였고 종횡비에 따른 해석을 실시한 결과 저온형 개질기의 경우 길이방향보다는 반경방향의 열전달을 증대시키는 방법이 효과적임을 확인하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.86.1-86.1
• /
• 2010

예비개질기(Pre-reformer)는 중대형 내부개질형 용융탄산염 연료전지(MCFC) 시스템에서 다양한 연료를 사용하기 위한 필수적인 화학반응기이다. 예비개질기는 스택 전단에 설치함으로서 스택 내부의 열균형을 유지하고, 다양한 원료를 연료로 이용할 수 있도록 하며, 황화물로부터 후단의 개질촉매 및 전극촉매를 보호하여 주개질 반응의 부담을 감소시켜 MCFC 시스템의 내구성 향상의 중요한 역할을 한다. 본 연구는 예비개질 반응기 설계에 CFD 모델링을 적용하기에 앞서 파일롯 반응기 내 농도/ 온도 구배를 측정하고자 하는 목적으로 수행되었다. 반응가스로는 천연가스 내 고차탄화수소(C2 이상) 중 상대적으로 높은 농도를 가진 에탄을 이용하였고, MCFC용 예비개질기의 운전특성을 고려하여 비교적 낮은 온도와 높은 수증기/탄소 비에서 단열반응기로 실험을 진행하였다. 향후 본 실험결과를 이용하여 CFD 모델링에 대한 검증을 수행할 예정이며, 하수처리장부생가스(ADG)/ 매립지 가스(LFG)용 MCFC 시스템을 위한 예비개질기 설계에도 적용을 하고자 한다.

• 에너지공학
• /
• 제22권2호
• /
• pp.226-236
• /
• 2013

고온개질기를 이용한 수증기 메탄 개질반응에 대해 실험 및 전산해석 기법을 이용하여 실제 개질기의 효율 및 개질기의 형상의 변화에 따른 열 분포 및 내부 유동에 대해서 연구하였다. 수증기 개질에 대한 반응모델은 Xu & Froment에 의해 개발된 수증기 반응 모델을 사용하였고, 그 결과로 고온개질기내에서 일어나는 화학반응은 Steam Reforming(SR), Water Gas Shift(WGS), Direct Steam Reforming(DSR) 반응이 다른 반응을 지배한다고 가정하였다. 고온개질기를 이용한 수증기 메탄 개질 반응 실험 결과로는 Steam Carbon Ratio(SCR)이 증가함에 따라 수소 수득율 또한 증가하고 일산화탄소와 메탄은 감소하는것을 알 수 있었다. 또한 입구가 한 개인 디자인과 두 개인 디자인을 비교, 분석하였을 때 입구가 두 개인 개질기보다 입구가 한 개인 개질기에서 열 분포 및 내부유동, 수소 수득율이 우수하다는 결과를 얻게 되었다.

• 한국운동역학회지
• /
• 제33권4호
• /
• pp.128-136
• /
• 2023

Objective: The aim of this study was to investigate the effect of an 8-week closed kinetic chain typed Reformer and Chair Pilates exercise on static and dynamic lower limb alignment for healthy female adults. Method: Ten healthy young female adults without musculoskeletal injury history in last 6 months (Age: 29.3 ± 3.5 yrs., Height: 165 ± 3.4 cm, Body mass: 58.2 ± 5.4 kg) participated in this study. All participants asked to join the 8-week closed kinetic chain typed Reformer and Chair Pilates exercise, and the program was conducted for 60 minutes twice a week. Participants were asked to be measure a static Q-angle and performed free squat one week before and after the program. A 3-D motion analysis with 8 infrared cameras and 5 channels of EMG was executed in this study. The effectiveness of the training was evaluated by paired t-test, and the significance level was set at .05. Results: A significantly decreased in internal rotation angles was found at hip joint during free squat after the training. Also, significantly decreased in lateral rotation angles were found at knee and ankle joint during free squat after training. Finally, significantly decreased in muscle activations were found at adductor longus and peroneus longus during free squat after training. Conclusion: From results of our study, it is concluded that an 8-week closed kinetic chain typed Pilates exercise positively effect on lower limb alignment during dynamic movement.

• 한국수소및신에너지학회논문집
• /
• 제26권2호
• /
• pp.156-163
• /
• 2015

The fuel cells have been investigated in the applications of marine as the high efficient and eco-friendly power generating systems. In this study, modeling of IR Type molten carbonate fuel cell (Internal Reforming Type molten carbonate fuel cell) has been developed to analyze the feasibility of thermal energy utilization. The model is developed under Aspen plus and used for the study of system performances over regarding fuel types. The simulation results show that the efficiency of MCFC system based on NG fuel is the highest. Also, it is also verified that the steam reforming is suitable as pre-reforming for diesel fuel.

• 설비공학논문집
• /
• 제16권7호
• /
• pp.615-622
• /
• 2004

Recently, the hybrid system combining fuel cell and gas turbine has drawn much attention owing to its high efficiency and ultra low emission. It is now on the verge of world wide development and various system configurations have been proposed. A national project funded by Korean government has also been initiated to develop a pressurized hybrid system. This work aims at presenting design performance analysis for various possible system configurations as an initial step for the system development. Study focuses are given to major design options including the power ratio between gas turbine and fuel cell, reforming method (internal or external), reforming heat source (reforming burner, cathode hot air, fuel cell heat release) and steam supply method for reformer (anode gas recirculation, external steam generator). A wide variation in performance among different configurations has been predicted.