• Nuclear Engineering and Technology
• /
• v.44 no.3
• /
• pp.331-342
• /
• 2012

Since the opening of the Shin-Kori #1,2 in 2005, fly ash mixed concrete has been used for NPP concrete structures under construction in Korea with the aim of preventing aging and improving durability. In this paper, the quality suitability of fly ash manufactured in Korea is assessed and the basic physical properties of fly ash mixed concrete and its durability against primary causes of aging are verified through experimental methods. Because of the internal structure filling effect from the pozzolanic reaction of fly ash and the resulting improvements in mechanical performance in such areas as strength and salt damage resistance, the durability of fly ash mixed concrete is shown to be superior. It is judged that this result can be applied in measures not only for improving the safety of NPP structures in operation in Korea but also for implementing effective structure life management should extending the life of structures be needed in the future.

• Journal of Mechanical Science and Technology
• /
• v.14 no.9
• /
• pp.928-934
• /
• 2000

This paper describes a method developed for the simulation of ring pack lubrication characteristic in an internal combustion engine. In general, the quantity of oil supply for piston ring lubrication may be insufficient in filling the entire volume formed at the interference between the piston ring and the cylinder liner. Thus the oil starvation condition should be considered in analyzing piston ring lubrication. In order to reasonably estimate the amount of oil left over on the cylinder liner, the flow rate at the posterior portion of the interface should be calculated with an adequate boundary condition that confirms flow continuity condition. In this analysis, oil starvation and open-end boundary conditions are considered at the inlet and outlet of the piston rings. The lubrication characteristic of each piston ring is obtained by an iterative method with sequential steps. It is revealed that piston rings are operated under oil starvation in most operating cycles and the result under these conditions are quite different from that with the fully-flooded assumption.

• Parasites, Hosts and Diseases
• /
• v.55 no.1
• /
• pp.65-69
• /
• 2017

A case of Taenia asiatica infection detected by small bowel series and colonoscopy is described. The patient was a 42-year-old Korean man accompanied by discharge of movable proglottids via anus. He used to eat raw pig liver but seldom ate beef. Small bowel series radiologic examinations showed flat tape-like filling defects on the ileum. By colonoscopy, a moving flat tapeworm was observed from the terminal ileum to the ascending colon. The tapeworm was identified as T. asiatica by mitochondrial DNA sequencing. The patient was prescribed with a single oral dose (16 mg/kg) of praziquantel.

• Parasites, Hosts and Diseases
• /
• v.55 no.6
• /
• pp.659-660
• /
• 2017

Biliary ascariasis is still the leading cause of surgical complication of ascariasis, though its incidence has been dramatically reduced. Herein, we report a case of biliary ascariasis for the purpose of enhancing awareness of parasitic infections as a possible cause. A 72-year-old male visited the emergency room of Dankook University Hospital on 12 July 2015, complaining of right-upper-quadrant pain. By endoscopic retrograde cholangiopancreatography (ERCP), a tubular filling defect in the right hepatic duct was detected. The defect was endoscopically removed and diagnosed as an adult female of Ascaris lumbricoides worm, of 30 cm length. Upon removal of the worm, the pain subsided, and the patient was discharged without any complication. When treating cases of biliary colic, physicians should not neglect biliary ascariasis as the possible cause.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.89-92
• /
• 2005

This study investigates influence of particle properties of crushed sand on the duality of concrete. The test shows that an increase of fineness modulus(FM) resulted in high slump and air contents, while compressive strength decreased due to decreased adhesion with reduction of surface area. As grain shape become rounder, the slump of concrete increased, due to reduction of internal friction, and increased air contents. The reduction of adhesion by abrasion of surface declined compressive strength during the process of manufacturing crushed sand. Increase of powder contents decreased slump and it also decreased air contents due to the effect of filling air void. In addition. using powder contents increased compressive strength, but could not find any difference of bleeding and tensile strength with particle properties.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.2
• /
• pp.94-101
• /
• 2017

Recently, the small quantity batch production method has come into the spotlight as there are more plastic processing methods. At the same time, the 3D printer market has become globally widespread due to expired 3D printer patents. In particular, the FDM method is widely used for cheap products and materials. However, the FDM scheme is not as good as the injection molding method for quality and strength. This study investigated the effect of the internal filling and strength according to layer thickness to search for the optimum printing of the factors (infill and layer thickness) that determine the strength of the model.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.9
• /
• pp.5474-5479
• /
• 2014

This study evaluated the residual stress and deformation for bracket castings of induction motors. Numerical analyses were performed to evaluate the residual stress distributions and displacements of bracket castings after the casting and final machining processes. Based on the analysis results, it was found that bracket casting was satisfied with the internal quality standards during the fabricating processes.

• Journal of the Korean earth science society
• /
• v.27 no.7
• /
• pp.757-767
• /
• 2006

Alluvial-plain deposits in the southeastern part of the Eumsung Basin (Cretaceous) are characterized by coarse-grained channel fills encased in purple siltstone beds. It represents distinct channel geometry, infill organization, and variations in facies distribution. The directions of paleocurrent, sedimentary facies changes, and channel-fill geometry can be used to reconstruct a channel network in the alluvial system developed along the southeastern margin of the basin. The channel-fill facies represent downstream changes: 1) down-sizing and well-sorting in clast and martix of channel fills and 2) internal organization of scour fill or gravel lag and overlying cross-stratified, planar-stratified beds. These findings suggest multiple stages of channel-filling processes according to flooding and subsequent stream flows. In the small-scale pull-apart Eumsung Basin (${\sim}7{\times}33km^2$ in area), vertical-stacked alluvial architecture of the coarse-grained channel fills encased in purple siltstone is expected to result from episodic channel shifting under a rapidly subsiding setting.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1995.10a
• /
• pp.64-67
• /
• 1995

Transfer Molding is currently the most widely used process for encapsulation integrated circuits(;IC). Although the process has been introduced over 20 years ago, generating billions of parts each year, it is far from being optimized. With each new mold, epoxy mold, epoxy mold compound, and lead-frame, lengthy period and expensive qualification runs have to be performed to minimized defects ranging from wire sweep, incomplete fill, and internal voids etc. This studies describes how simulation can be applied to transfer molding to yield acceptable design and processing parameter. The non-isothermal filling of non-newtonian reactive epoxy molding compound(;EMC) in a multi-cavity mold is analyzed. Sensitivity analysis is conducted to investigate the influence of process deviations on the final molded profile. This study trend is carried out by following some heuristic process guidelines.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.939-944
• /
• 2003

The analysis involves an adaptive grid that is created under a criterion of element categorization of filling states and locations in the total region at each time step. By using an adaptive grid wherein the elements, finer than those in internal and external regions, are distributed at the surface region through refinement and coarsening procedures, a more efficient analysis of transient fluid flow with free surface is achieved. Using the proposed numerical technique, the collapse of a dam is analyzed. The numerical results agree well with the theoretical solutions as well as with the experimental results. Through comparisons with the numerical results of several cases using different types of grids, the efficiency of the proposed technique is verified.