• Corrosion Science and Technology
• /
• v.20 no.4
• /
• pp.189-195
• /
• 2021

A technology for designing and licensing a dedicated radiation shielding facility needs to be developed for safe and efficient operation an R&D center. Technology development is important for smooth operation of such facilities. Causes of damage to internal structures (such as baffle former bolt (BFB) of pressurized water reactor) of a nuclear power reactor should be analyzed along with prevention and countermeasures for similar cases of other plants. It is important to develop technologies that can comprehensively analyze various characteristics of internal structures of long term operated reactors. In high-temperature, high-pressure operating environment of nuclear power plants, cases of BFB cracks caused by irradiated assisted stress corrosion cracks (IASCC) have been reported overseas. The integrity of a reactor's internal structure has emerged as an important issue. Identifying the cause of the defect is requested by the Korean regulatory agency. It is also important to secure a foundation for testing technology to demonstrate the operating environment for medium-level irradiated testing materials. The demonstration testing facility can be used for research on material utilization of the plant, which might have highest fluence on the internal structure of a reactor globally.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.143-152
• /
• 2002

European side impact analysis of an electric vehicle was done using the robust design method. In order to minimize VC as well as rib deflection, the injury response table which consists of rib deflection and VC response table has been introduced. The sensitivities and interactions are almost the same when it was compared with those of rib deflection and VC response table. Using internal energy of the factors, the starting time of dummy rib deflection and the contact average velocity, the internal energy and time-velocity response table were introduced. It is shown that the results of the new response tables have the similar characteristics to those of the Injury response table. It is suggested that the internal energy and time-velocity response table should be utilized to minimize injuries.

• Proceeding of EDISON Challenge
• /
• 2016.03a
• /
• pp.222-227
• /
• 2016

In this paper, the optimized design for bow structure was investigated by using EDISON software. Considering the mechanism of the bow, non-linear FEM analysis was essential. The factors of the design are height, width, number of holes and taper value. High performance of the internal energy and lowest mass were main issues. The limit of the von-mises stress was yield strength for the material. Material was chosen by considering typical bow material, Aluminum. Using Taguchi method($L_9$), 9 models were selected and contribution rate was calculated for each factors. Following the contribution rate, 3 factors were fixed and optimized model was predicted. After making optimized model for FEM analysis, the value of internal-energy, mass for FEM model were compared with predicted value, calculated the percentage error and figure out the reliability of Taguchi method.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.925-930
• /
• 2008

As office automation appliances and communication equipments are adopted in office buildings, internal heat gains increase gradually. When making simulation model, internal heat gains are usually set up with standard values or ignored. Therefore, the impact of the internal heat gains has been ignored or not been focused although it is recognised as significant contributor to heating/cooling load of buildings. This study focused on the impact of internal heat gains on curtain wall buildings. the amount and schedules of heat internal gains profiles not only affect the profiles of heating/cooling loads, but also make impact on reducing the effectiveness of high performance glazing systems. It is important to identify internal heat gains profiles before considering the installation of high performance glazing systems.

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.4
• /
• pp.377-383
• /
• 2017

This paper presents the performance characteristics of a 1 kW solid oxide fuel cell (SOFC) stack under various internal reforming and fuel utilization conditions. The Research Institute of Industrial Science & Technology (RIST) developed the 9-cell stack using a $20{\times}20cm^2$ anode supported planar cell with an active area of $324cm^2$. In this work, current-voltage characteristic test, fuel utilization test, continuous operation, and internal reforming test were carried out sequentially for 765 hours at a furnace temperature of $700^{\circ}C$. The influence of fuel utilization and internal reforming on the stack performance was analyzed. When the 1 kW stack was tested at a current of 145.8 A with a corresponding fuel utilization of 50-70% (internal reforming of 50%) and air utilization of 27%, the stack power was approximately 1.062-1.079 kW. Under continuous operation conditions, performance degradation rate was 2.16%/kh for 664 hours. The internal reforming characteristics of the stack were measured at a current of 145.8. A with a corresponding fuel utilization of 60-75%(internal reforming of 50-80%) and air utilization of 27%. As fuel utilization and internal reforming ratio increased, the stack power was decreased. The stack power change due to the internal reforming ratio difference was decreased with increasing fuel utilization.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.108.5-108
• /
• 2002

Recently, the more advanced control technologies are required to deal with the fast and accurate motion in manipulators. For these requirements, many manipulator control methods have been developed such as a computed torque method. This paper proposes a design method, a two-degrees-of-freedom internal model control (TDOF IMC), of the manipulator position control based on combination of the one-degree-of-freedom internal model control (ODOF IMC) system and the disturbance observer. The proposed control scheme is implemented for the position control, which leads the slave manipulator to the desired location by the master arm. The experimental results are presented and discussed through the imp...

• The Journal of Internal Korean Medicine
• /
• v.11 no.2
• /
• pp.104-111
• /
• 1990

The results of the Review of literature, the treatment of globus hystericus were summerized as follows ; first, use the method of adjusting the flow of vital energe, second, to break through the phlegm, to smooth the flow of vital energy, to releive stagnancy of vital energy, to keep air or gas going downward, and then, to restore the normal functioning of stagnancy of vital energy, to remove evil(heat) from the lung, antasthma to resolve phlegm, to regulate the vital function of the stomach as displling dampness through ditiresis by using mild-flavored drugs, to dispel pathogenic factors from the exterior of the body by diaphoresis. As the prescription of globus hystericus, Samultang were used the most frequently, and then, chilgitang, Gamisachiltang, Daechilgitang, Banhahubaktang, Gamileejintang, Bunsingiyum, samayum, Soyousan, Mokhyangbang were used.

• Journal of The Korean Astronomical Society
• /
• v.2 no.1
• /
• pp.33-39
• /
• 1969

The gain of internal energy of a star cluster caused by the tidal attraction of our Galaxy is examined. Expressions are derived which include the effects of a two-body orbit and internal motions of the cluster. These formulae are compared with previous results based on (i) uniform rectilinear motion and (ii) neglect of internal motions induced by cluster gravitation(i.e., impulsive approximation), and it is found that these simplifying assumptions generally introduce significant uncertainties.

• East Asian mathematical journal
• /
• v.37 no.5
• /
• pp.619-626
• /
• 2021

In [1, 2], we studied the string-like system with time-varying delay. Unlike the string system, the plate system must consider both longitudinal and transverse strains. First, we consider the physical phenomenon of an axially moving plate concerning kinetic energy, potential energy, and work dones. By the energy conservation law in physics, we have a nonlinear plate-like system with internal time delay.

• Nuclear Engineering and Technology
• /
• v.42 no.1
• /
• pp.109-114
• /
• 2010

Bioassay data analysis software (BiDAS-2007) has been developed by KAERI, which adds several new functions to its previous version. New functions of the BiDAS-2007 computer code enable the user not only to do a simultaneous analysis by using two or more types of bioassay for the best internal dose evaluation, but also to do a continual internal dose evaluation from a change of the internal exposure conditions such as an intake type (acute, chronic), an intake pathway (inhalation, ingestion), an absorption type (Type F, M, S), and a particle size (AMAD, activity median aerodynamic diameter), and also to estimate the intakes in various conditions of an internal exposure at a time. The values calculated by the BiDAS-2007 code are consistent and in good agreement with those values by IMIE-2004 code by Berkovski and IMBA code by Birchall. The BiDAS-2007 computer code is very useful and user-friendly to estimate the radionuclide intakes and committed effective doses of a radiation worker.