• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.2 no.4
• /
• pp.40-45
• /
• 2003

In this paper, to choose the optimum CBN wheel for Internal Grinding at LM Guide, among 7 types of CBN-wheels, the 2 types of CBN-wheels, which were the macrofracture CBN wheel and the microfracture CBN wheel, have been used, and the SCM420H have been used as the workpiece. The working conditions in the grinding experiments were depth-of-cut, table speed, and spindle speed for 4 types of the CBN grinding wheels, 2 types of the lubrications. By the experiments, the loading effect of the microfracture types of the CBN-wheel needed a short dressing interval and resulted in grinding wheel wear and bad surface roughness. However, a macrofracture type of CBN-wheel with the concentration of 100, CB120Q100V showed the best surface roughness quality at a low table speed for internal grinding at LM-guide.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.39-43
• /
• 1996

This paper described on the effect of residual stocks in internal grinding of tungsten carbide materials in order to improve the grinding efficiency as well as grinding accuracy. Though the fundamental investigation is carried out for tungsten carbide materials using electroplated diamond wheel, the residual stock after grinding process is effective to the grinding effciiency. The obtained results are as follows: (1) Under the depth of cut(t) is constant and decreasing the workpiece velocity(Vw), the resiudal stock after grinding is increased, but the difference is little less than the difference by table speed. (2) Increasing the wheel velocity, the residual stock after grinding is decreased. Therefore in order to minimize the residual stock, the wheel velocity should be increased as far as possible. (3) The surface foughness and out-of roundness increased with depth of cut and table speed, and decreased with wheel velocity, but it may as well adopt as much as polssible under the dimensional tolerance which is required for high efficiency grinding. (4) In order to remove residual stock, the spark-out grinding shoule be done, and it also can be improved about 20 .approx. 25% throughout spark-out grinding, and the number of optimal spark-out times were within 10 times.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.6 no.1
• /
• pp.34-44
• /
• 1997

This study presents the recursive constraint bounding(RCB) method to reduce the cycle time in internal cylindrical plunge grinding process. This method can cope with process noise as well as modeling bias. The main features of RCB method are its utilization of measurements at the end of each cycle and its use of monotonicity analysis for determining the extremes of bias and noise. This method is investigated in simulation and evaluated by experiment in internal cylindrical plunge grinding operation. The results from simulation and experiment show that it is effective in reducing cycle time in spite of modeling uncertainty in the forms of process noise and modeling bias.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.5
• /
• pp.60-66
• /
• 1996

Precision of bearing race is very important to maintain the clearance between ball and inner race. In internal grinding of bearing race, its roundness is dependent on shoe wear, accuracy of jig, dressing method and grinding conditions. In this study, the characteristics of shoe wear and eccentricity of workpiece were investigated experimentally. When wear of fornt shoe wear reaches at 100.mu. m and that of rear shoe reaches at 114 .mu. m, eccentricity of inner race is increased to 1.4 .mu. m. Roundness of race is mainly related to wear of rear shoe and ring type shoe is recommended to improve roundness of race.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.6
• /
• pp.701-708
• /
• 2011

Although Titanium material has superior properties, it belongs to difficult-to-machine materials. The present research applies magnetic abrasive finishing to precision machining of internal-face of titanium pipes, and analyzed & assessed the influence of grinding conditions on magnetic abrasive effects through the removed amount and surface roughness of materials. There was the influence on grinding properties according to change of rotational speed, a total input of mixed powder and an input of grinding liquid, and when the total input, rotational speed and ratio of electrolytic iron versus magnetic abrasives are 8g and 1000rpm, it was most advantageous in aspects of surface roughness and material removal amount, and the grinding liquid remarkably improved the surface roughness and material removal amount only with addition of trace amounts of light oil rather than dry machining conditions. And a result of considering the influence on grinding properties by using an inert gas (Argon gas) for improving grinding properties of the internal-face of titanium pipe, the present research has obtained improvement effects in the removal amount and surface roughness through utilization of an inert gas.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.1 s.94
• /
• pp.108-115
• /
• 1999

Since grinding is a more complicated process than any other machining process, it is hard for operators to setup a grinding machine properly and to find out correctly abnormal grinding states resulting in damages to products. Abnormalities would be caused by improper setup, improper dressing/grinding conditions which are likely to be occurred without skilled operators' attention. In this study, an AE monitoring unit is developed to help operators conduct with ease setup, and set properly dressing/grinding conditions. AErms(root-mean-square) signal being monitored, on-going process states during grinding and dressing is visualized for machine operators to judge whether the processes are in good condition. Evaluation tests are carried out on centerless grinding machines-both cylindrical and internal. The developed AE monitoring system is verified to be useful to check grinding/dressing states in process even in the centerless grinding of which process is most unknown among various grinding methods because of the complex structure.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.10a
• /
• pp.71-76
• /
• 2003

This paper describes the characteristic of a large-diameter pipe to obtain smooth surface using Electropolishing after grinding using a non-woven fabric. Grinding using a non-woven fabric is possible under lower load and fine effect comparing with Wheel grinding. Also, the ion from the surface of the metal is eliminated by means of an electrical potential and current in Electropolishing. Electropolishing is used for leveling the surface, improving the physical appearance of the part, promoting corrosion properties and reducing contamination and adhesion of the surface. Therefore, the aim of the present study is to investigate the internal machining of a large-diameter pipe for semiconductor using experimental design method.

• Korean Journal of Computational Design and Engineering
• /
• v.5 no.4
• /
• pp.312-318
• /
• 2000

In this study, an exclusive CAD/CAM system is developed for enhancing the effectiveness and productivity of CNC universal cylindrical grinding machines on which the external/facing/internal grinding cycles and the wheel dressing cycles are integratively carried out. The CAD/CAM system can manage the various processes such as geometry design, NC code generation, NC code verification, DNC operation, and so on. Especially, the feature-based modeling concept is introduced to improve the geometry design efficiency. And the NC code verification is realized by virtual manufacturing technique based on the real-time analysis of NC codes and the boolean operation between workpiece and wheel.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.435-440
• /
• 2000

In this study, we aims to develop the machining technology for the ultra precision surface and profile accuracy. For this purpose, we construct the electrolytic in process grinding system (ELID grinding) and apply to the cylindrical and internal grinding. Through the various machining experiments such as SCM steel., ceramics, tungsten carbide etc., we have obtained nanometer surface roughness. And we have applied this mirror grinding technique to hydraulic manual valve and mold core of mini disk optical pick-up base. For the development of fine mechanical part machining technology, e have made multi fiber optical connector using fine grinding technology. And constructed micro drilling system with process monitoring system which is possible to drill 50${\mu}{\textrm}{m}$ diameter hole.

• Design & Manufacturing
• /
• v.17 no.2
• /
• pp.42-46
• /
• 2023

Currently, fossil resources are depleting rapidly. We are looking for energy to replace fossil fuels. They are trying to use electricity to replace internal combustion locomotives. Secondary battery raw materials and chemical additives are pulverized by the high-speed rotation of the grinding disc of the Classifier Separator Mill. Grinding Disc Assembly requires characteristics to withstand abrasion, corrosion, high-speed rotational force and impact. Domestic and foreign grinding discs were analyzed through abrasion resistance, hardness, bending strength, and tensile adhesion strength tests.