• 대한수학회지
• /
• 제54권1호
• /
• pp.249-265
• /
• 2017

Interface problem here refers to a second order elliptic problem with a discontinuous coefficient for the second order derivatives. For the corresponding boundary value problem, the maximum principle still holds but Hopf's boundary point lemma may fail. We will give an optimal power type estimate that replaces Hopf's lemma at those boundary points, where this coefficient jumps.

• Tribology and Lubricants
• /
• 제16권4호
• /
• pp.289-294
• /
• 2000

This paper present the contact stresses, which considers the shear stress at the cam and follower interface in the direct acting type valve train system of a high speed engine. To determine the contact condition, the normal contact forces are calculated by using the lumped mass dynamic modeling. The line contact is considered between the cam and follower interface. The variations of dynamic stresses are presented as a function of camshaft rotational angle. Also the effects of various design parameters are investigated.

• 전자공학회논문지A
• /
• 제30A권3호
• /
• pp.61-66
• /
• 1993

The interface properties of Fluoride/GaAs structures were investigated. It was foung that rapid thermal annealing(RTA) typically 800-850$^{\circ}C$for 1 min, was useful for improving the interface properties of that structures. The analysis by means of SIMS indicated that interdiffusion of each constitutional atom through the interface was negligible. The interfacial atom bonding model for RTA treatment was proposed. Bases on these results, inversion-type GaAs MISFET was fabricated using standard planar technologies.

• 한국농공학회지
• /
• 제33권2호
• /
• pp.82-93
• /
• 1991

The objective of this paper is to show that the soil-geotextile interaction needs to he addressed in addition to the usual tensile and modulus properties when the geotextile is being designed for a specific application. The soil-geotextile interaction can be directly assessed by standard direct shear test. The data presented here show that the shear strength paramaters describing the soil-geotextile interface can he greatly influenced by the type of the geotextile. In this investigation, we examined nine different geotextiles of varying construction and surface textures with two standard soil, under five loading conditions, and compared the shear strength and the frictional resistance with the corresponding values of soil itself The following conclusions were drawned from this study. 1. The shear stress-strain curve shows that there are the residual shear stresses at the soil-geotextile interface. Because of the hydraulic gradient between the soil and the geotextile, the excessive pore water can migrate into the geotextile and among the filaments and dissipate through the soil-geotextile interface. 2. The shear strength of the soil-geotextile interface is affected by the moisture content of the soil. At moisture content lower than the optimum water content of the Proctor compaction test, the shear strength of the soil-geotextile interface is greater. 3. The type and surface roughness of the geotextile have the greatest influence on the interface friction angle between the soil and the geotextile.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2002년도 International Meeting on Information Display
• /
• pp.1081-1081
• /
• 2002

Top emission organic EL devices were fabricated by using metal-doped cathode interface layer to achieve low drive voltages. Also, facing-targets-type sputtering was used to sputter indium-tin oxide layer on top of organic active layer. The devices fabricated in this study showed reasonably high external quantum efficiency of about 1 % which is comparable to that of bottom-emission-type devices.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1999년도 하계종합학술대회 논문집
• /
• pp.102-105
• /
• 1999

AAL type 2 provides for the bandwidth efficient transmission of low bit rate, short and variable packets in delay sensitive application. The service object for these networks ranges from POTS to multimedia conference. In this paper, we present one possible architecture which common part sublayer for new AAL type 2. The proposed CPS function has been achieved with on a FPGA The proposed architecture is faithful to the standardization of ITU-T and ATM-forum recommendation The proposed architecture applies to variable packet length from architecture CODECs for cellular network.. It's maximum process capability is 155Mbps with 256 CIDs. The architecture has sync./async. interface to application block and UTOPIA interface is used for physical layer interface.

• 한국공간구조학회논문집
• /
• 제21권3호
• /
• pp.35-42
• /
• 2021

An experimental study was carried out to evaluate the shear performance at the interface composed of structural laminates and concrete. The main variables are the number of CLT layers and the shape of the shear connector. The number of CLT layers consisted of 3 and 5 layers. A total of 6 test specimens for shear performance evaluation were prepared in the form of a shear connector, a direct screw type and a vertically embedded type. As a result of the experiment, similar behavior was shown in all specimens, regardless of the number of layers, including direct screw type (SC series) and vertically embedded type (VE series). The behavior at the joint surface was damaged due to the occurrence of initial shear cracks, expansion of shear groove cracks, and splaying at the interface after the maximum load.After the maximum load, the shear strength decreased gradually due to the effect of the shear connector. It can be seen that the shear strength of all specimens is determined by shear and compression stress failure of concrete at the interface of the notch joint.

• 전자공학회논문지T
• /
• 제36T권1호
• /
• pp.51-57
• /
• 1999

본 논문은 온도센서 RSD. Pt 100Ω의 감지신호가 Temperature Controller의 릴레이 출력을 발생시키고 PLC 입력접점으로 입력시켜 1Scan Time으로 연산된 PLC 출력을 접점 P030에 Interface Unit를 연결시키므로 부하를 구동시키는 개발장비인 Wired Logic Type Unit에 대해서 기술하였다. 현재 PLC 교육장에서 프로그램 되어진 PLC가 부하를 구동시킬 수 있는 국내의 교육 PLC Test Kit로는 PLC와 부하 사이에 Interface 과정이 무시된 상태에서 PLC의 교육을 하도록 되어있다. 개발 키 트는 이 점을 보안하기 위해서 각종 센서 중 전자에서 언급한 온도 센서 Pt 100Ω을 이용한 온도 제어기의 릴레이 출력이 PLC 입력으로 피드백 되었을 때, 연산된 PLC 출력접점에 WLTU를 삽입시켜 PC, PLC와 부하 사이에 실시간 시스템으로 구동 시킬 수 있는 설비로, PLC 사용의 핵심원리를 쉽게 이해하고 알아 볼 수 있었다. 부하 Interface Unit인 WLTU의 구성은 구동 부분인 유 접점, 무접점, 센서, 지시 등, A접점, B접점 부하인 Motor로 나누었다.

• 대한치과보철학회지
• /
• 제42권2호
• /
• pp.226-237
• /
• 2004

Purpose: Four finite element models were constructed in the mandible having a single implant fixture connected to the first premolar-shaped superstructure, in order to evaluate how the shape of the fixture and the implant-abutment connection would influence the stress level of the supporting tissues fixtures, and prosthethic components. Material and methods : The superstructures were constructed using UCLA type abutment, ADA type III gold alloy was used to fabricate a crown and then connected to the fixture with an abutment screw. The models BRA, END , FRI, ITI were constructed from the mandible implanted with Branemark, Endopore, Frialit-2, I.T.I. systems respectively. In each model, 150 N of vertical load was placed on the central pit of an occlusal plane and 150 N of $40^{\circ}$ oblique load was placed on the buccal cusp. The displacement and stress distribution in the supporting tissues and the other components were analysed using a 2-dimensional finite element analysis . The maximum stress in each reference area was compared. Results : 1. Under $40^{\circ}$ oblique loading, the maximum stress was larger in the implant, superstructure and supporting tissue, compared to the stress pattern under vertical loading. 2. In the implant, prosthesis and supporting tissue, the maximum stress was smaller with the internal connection type (FRI) and the morse taper type (ITI) when compared to that of the external connection type (BRA & END). 3. In the superstructure and implant/abutment interface, the maximum stress was smaller with the internal connection type (FRI) and the morse taper type (ITI) when compared to that of the external connection type (BRA & END). 4. In the implant fixture, the maximum stress was smaller with the internal connection type (FRI) and the morse taper type (ITI) when compared to that of the external connection type (BRA & END). 5 The stress was more evenly distributed in the bone/implant interface through the FRI of trapezoidal step design. Especially Under $40^{\circ}$ oblique loading, The maximum stress was smallest in the bone/implant interface. 6. In the implant and superstructure and supporting tissue, the maximum stress occured at the crown loading point through the ITI. Conclusion: The stress distribution of the supporting tissue was affected by shape of a fixture and implant-abutment connection. The magnitude of maximum stress was reduced with the internal connection type (FRI) and the morse taper type (ITI) in the implant, prosthesis and supporting tissue. Trapezoidal step design of FRI showed evenly distributed the stress at the bone/implant interface.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.671-674
• /
• 2001

The dynamic photoelasticity with the aid of Cranz-Shardin type high speed camera system is utilized to record the dynamically propagating behavior of the interface crack. This paper investigates the effects of the stiffness of interface defect(exist along the path of the crack propagation) on the dynamic interface crack propagation behavior by comparing the experimental isochromatic fringes to the theoretical stress fields.