• 한국진공학회지
• /
• 제7권2호
• /
• pp.82-87
• /
• 1998

$O_2$기체에 $NH_3/O_2$기체를 첨가하여 실리콘 표면에 산화막을 형성하는 $NH_3/O_2$산화법 에 의한 산화공정시 반응석영관 외부에 방출하는 기체는 $N_2,O_2$및 $H_2O$이며 극소량의 $CO_2$, NO 및 $NO_2$가 검출되었다. 두 종류의 산화제($O_2$ 및 $H_2O$)가 산화에 기여하며 성장률은 $NH_3$및 $O_2$ 의 부분압과 온도에 의해 결정되며, 그 기울기는 건식 및 습식 산화법의 중간에 평행 하게 위치함을 확인하였다. Auger Electron Spectroscopy(AES) 측정결과 $NH_3/O_2$ 산화막은 정확한 $SiO_2$의 화학량론을 가지며 $SiO_2/Si$계면에 발생하는 결합을 억제하며 고정전하의 발 생을 최소화함을 알 수 있었다. $NH_3/O_2$ 산화막(470$\AA$)의 항복전압을 57.5Volt이며, C-V특성 곡선을 축정한 결과 플랫밴드 전압은 0.29Volt이며 곡선의 형태는 이상곡선과 일치하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.131-131
• /
• 2010

We compared the electrical, optical, structural, and interface properties of indium zinc oxide (IZO)-Ag-IZO and IZO-Au-IZO multilayer electrodes deposited by linear facing target sputtering system at room temperature for organic photovoltaics. The IZO-Ag-IZO and IZO-Au-IZO multilayer electrodes show a significant reduction in their sheet resistance (4.15 and 5.49 Ohm/square) and resistivity ($3.9{\times}10^{-5}$ and $5.5{\times}10^{-5}$Ohm-cm) with increasing thickness of the Ag and Au layers, respectively. In spite of its similar electrical properties, the optical transmittance of the IZO-Ag-IZO electrode is much higher than that of the IZO-Au-IZO electrode, due to the more effective antireflection effect of Ag than Au in the visible region. In addition, the Auger electron spectroscopy depth profile results for the IZO/Ag/IZO and IZO/Au/IZO multilayer electrodes showed no interfacial reaction between the IZO layer and Ag or Au layer, due to the low preparation temperature. To investigate in detail the Ag and Au structures on the bottom IZO electrode with increasing thickness, a synchrotron x-ray scattering examination was employed. Moreover, the OSC fabricated on the IZO-Ag-IZO electrode shows a higher power conversion efficiency (3.05%) than the OSC prepared on the IZO-Au-IZO electrode (2.66%), due to its high optical transmittance in the wavelength range of 400-600 nm, which is the absorption wavelength of the P3HT:PCBM active layer.

• Journal of Welding and Joining
• /
• 제29권6호
• /
• pp.65-70
• /
• 2011

The effect of flip chip bonding parameters on formation of intermetallic compounds (IMCs) between Au stud bumps and Sn-3.5Ag solder was investigated. In this study, flip chip bonding temperature was performed at $260^{\circ}C$ and $300^{\circ}C$ with various bonding times of 5, 10, and 20 sec. AuSn, $AuSn_2$ and $AuSn_4$ IMCs were formed at the interface of joints and (Au, Cu)$_6Sn_5$ IMC was observed near Cu pad side in the joint. At bonding temperature of $260^{\circ}C$, $AuSn_4$ IMC was dominant in the joint compared to other Au-Sn IMCs as bonding time increased. At bonding temperature of $300^{\circ}C$, $AuSn_2$ IMC clusters, which were surrounded by $AuSn_4$ IMC, were observed in the solder joint due to fast diffusivity of Au to molten solder with increased bonding temperature. Bond strength of Au stud bump joined with Sn-3.5Ag solder was about 23 gf/bump and fracture mode of the joint was intergranular fracture between $AuSn_2$ and $AuSn_4$ IMCs regardless bonding conditions.

• 한국재료학회지
• /
• 제3권3호
• /
• pp.310-315
• /
• 1993

P-type(100)Si Wafer 위에 400$\AA$의 Ta를 증착하여 열산화법으로 ${Ta_2}{O_5}$박막을 형성시킴 후 RTA후처리를 통하여 절연파괴전장 특성 개선을 이루고자 하였다. 유전상수에 미치는 RTA후처리의 영향은 미약하지만 절연파괴전장을 나타내었으나 결정화 온도 이하의 RTA온도에서는 절연파괴전장이 5.4MV/cm로 RTA효과가 크게 나타났다. 이러한 RTA효과는 RTA온도 $575^{\circ}C$에서 flat band voltage shift가 RTA 시간에 따라 변화가 없는 것으로 미루어 보아 RTA효과는 계면 변화에 의한 것이 아님을 알 수 있었으며, RBS 분석을 통하여 ${Ta_2}{O_5}$1박막의 치밀화에 의한 것임을 확인할 수 있었다.

• Restorative Dentistry and Endodontics
• /
• 제21권2호
• /
• pp.505-516
• /
• 1996

The effects of application of dentin desensitizer containing glutaraldehyde (Gluma Desensitizer) and dentin adhesive system (All Bond 2) to the exposed dentin on the intradental nerve activity (INA) and the occluding aspects of dentinal tubules were investigated in cat canine teeth. Single pulp nerve units were dissected from the inferior alveolar nerve and indentified as $A{\delta}$-fiber units. The INAs elicited by 4M NaCl before and after the application of each experimental agent were compared. The morphological changes of exposed dentin surfaces and dentinal tubules in the dentin specimens used to record INAs were observed by SEM. The results obtained were as follows. 1. Eight $A{\delta}$-fiber units (conduction velocity: $8.0{\pm}4.0m$/sec) were identified. 4M NaCl evoked an irregular burst of action potentials which ceased immediately after washing. 2. In 4 $A{\delta}$-fiber units, the change of INA after the application of Gluma Desensitizer was $133.9{\pm}80.7%$ when it was compared with the INA before the application of the same agent. 3. In 4 $A{\delta}$-fiber units, application of All Bond 2 completely abolished the INA induced by 4M NaCl. 4. In specimens applied with Gluma Desensitizer, the formation of hybrid layer as well as the identification of resin penetration and reaction products with proteins in dentinal tubules were not clearly observed in interface between dentin and adhesive resin. In specimens applied with All Bond 2, the gap width of 2-$3{\mu}m$ was formed between exposed dentin and adhesive resin, and the hybrid layer and resin tags were not clearly formed either.

• 한국지능시스템학회논문지
• /
• 제20권3호
• /
• pp.388-393
• /
• 2010

문화콘텐츠기술(CT, Culture Technology)은 문화 산업 발전을 위한 기술로 문화콘텐츠 기획과 상품화, 미디어탑재, 전달의 가치사슬 과정 등 문화상품의 부가가치를 높이기 위해 소용되는 모든 형태의 유무형의 기술이다. 문화콘텐츠 기술(CT)분야에서 음악의 특징을 분석하여 다양한 어플리케이션을 개발하는 연구가 활발히 진행되고 있다. 이와 관련된 연구 중 EEG를 측정하고 그 결과에서 음악적 자극에 대한 반응을 검출하여 활용하는 연구가 주목받고 있다. 본 논문에서는 EEG에서 음악적 자극에 대응되는 반응신호들을 증폭시켜 평균화 하는 방법인 ERP(Event-Related Potentials) 실험을 기반으로 음색을 추출하는 과정에서 노이즈를 제거하기 위한 방법으로 ICA 알고리즘을 적용하여 음색 추출 및 노이즈 제거 결과에 따른 EEG의 특성을 분석하여 적용한다.

• 한국전기전자재료학회논문지
• /
• 제32권1호
• /
• pp.70-77
• /
• 2019

$SiO_x$ nanoparticles were granulated, and their microstructures and effects on electrochemical behaviors were investigated. In spite of the promising electrochemical performance of $SiO_x$, nanoparticles have limitations such as high surface area, low density, and difficulty in handling during slurry processing. Granulation can be one solution. In this study, pelletizing and annealing were conducted to create particles with sizes of several decades of micron. Decrease in surface area directly influences the initial charge and discharge process when granules are applied as anode materials for Li-ion batteries. Lower surface area is key to decreasing the amount of irreversible phase-formation, such as $Li_2Si_2O_5$, $Li_2SiO_3$ and $Li_4SiO_4$, as well as forming the solid electrolyte interface. Additionally, aggregation of nanoparticles is required to obtain further enhancement of the electrochemical behavior due to restrictions that there be no $Li_4SiO_4$-related reaction during the first discharge process.

• 패션비즈니스
• /
• 제23권2호
• /
• pp.77-88
• /
• 2019

One way of appling 3D printing to garments is through the combination of 3D polymer filaments in textile fabrics. it is essential to understand the interface between the polymer and the 3D composite fabric in order to enhance the adhesion strength between the polymers and the peeling strength between the fabric and the polymer. In this study, the adhesion of composite printed specimens using a combination of fabric and polymers for 3D printing was investigated, and also the change in adhesion was investigated after the composite fabric printed with polymers was subjected to constant pressure. Through this process, the aims to help develop and utilize 3D printing textures by providing basic data to enhance durability of 3D printing composite fabrics. The measure of the peeling strength of the composite fabric prepared by printing on a fabric using PLA, TPU, Nylon polymer was obtained as follows; TPU polymer for 3D printing showed significantly higher peel strength than polymers of composite fabric using PLA and Nylon polymer. In the case of TPU polymer, the adhesive was crosslinked because of the reaction between polyurethane and water on the surface of the fabric, thus increasing the adhesion. It could be observed that the adhesion between the polymer and the fiber is determined more by the mechanical effect rather than by its chemical composition. To achieve efficient bonding of the fibers, it is possible to modify the fiber surface mechanically and chemically, and consider the deposition process in terms of temperature, pressure and build density.

• 대한금속재료학회지
• /
• 제47권10호
• /
• pp.681-685
• /
• 2009

$CeO_2$ buffer layers have been deposited on YSZ single crystal substrates via a radio-frequency sputtering method. We focused on the texture development of $CeO_2$ with out-of-plane alignment and its effects on a superconducting YBCO layer, which was deposited by metal organic deposition. $CeO_2$ layers were grown epitaxially on single crystal YSZ substrates and subsequent YBCO layers were also grown epitaxially from $CeO_2$ layers. It was observed that the intensity of $CeO_2$(200) decreased with deposition temperature. ${\theta}-2{\theta}$ scan FWHM values of $CeO_2$(200) were inversely proportional to the peak intensities of $CeO_2$(200). The sample with the lowest $CeO_2$(200) intensity and poor out-of-plane alignment showed a strong reaction with the MOD-YBCO layer resulting in a thicker $BaCeO_3$ layer. The texture and superconducting property of the YBCO layer were affected indirectly by the formation of a $BaCeO_3$ layer at the interface between the $CeO_2$ and YBCO layers.

• Clinical and Experimental Reproductive Medicine
• /
• 제48권2호
• /
• pp.132-141
• /
• 2021

Objective: Lipopolysaccharide (LPS) from Gram-negative bacteria causes poor uterine receptivity by inducing excessive inflammation at the maternal-fetal interface. This study aimed to investigate the detrimental effects of LPS on the attachment and outgrowth of various types of trophoblastic spheroids on endometrial epithelial cells (ECC-1 cells) in an in vitro model of implantation. Methods: Three types of spheroids with JAr, JEG-3, and JAr mixed JEG-3 (JmJ) cells were used to evaluate the effect of LPS on early implantation events. ECC-1 cells were treated with LPS to mimic endometrial infection, and the expression of inflammatory cytokines and adhesion molecules was analyzed by quantitative real-time polymerase chain reaction and western blotting. The attachment rates and outgrowth areas were evaluated in the various trophoblastic spheroids and ECC-1 cells treated with LPS. Results: LPS treatment significantly increased the mRNA expression of inflammatory cytokines (CXCL1, IL-8, and IL-33) and decreased the protein expression of adhesion molecules (ITGβ3 and ITGβ5) in ECC-1 cells. The attachment rates of JAr and JmJ spheroids on ECC-1 cells significantly decreased after treating the ECC-1 cells with 1 and 10 ㎍/mL LPS. In the outgrowth assay, JAr spheroids did not show any outgrowth areas. However, the outgrowth areas of JEG-3 spheroids were similar regardless of LPS treatment. LPS treatment of JmJ spheroids significantly decreased the outgrowth area after 72 hours of coincubation. Conclusion: An in vitro implantation model using novel JmJ spheroids was established, and the inhibitory effects of LPS on ECC-1 endometrial epithelial cells were confirmed in the early implantation process.