• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.8
• /
• pp.891-898
• /
• 2008

In this paper, we have studied on the possibilities of the biomaterial detection using single-walled carbon nanotube (SWNT) based on interdigital capacitors. For the four different configurations, such as interdigital capacitor, SWNT in the $5\;{\mu}m$ gap interdigital capacitor, biotinlated SWNT, and biotin and sreptavidin immobilization cases, the resonant frequency has been measured as 10.02 GHz, 11.02 GHz, 10.82 GHz, and 10.22 GHz, respectively. Assuming that the resonant frequency reflects the capacitance changes due to binding of two-different permittivity biomaterials, we have suggested an equivalent circuit model based on measured results, confirming the capacitance changes. For biotinlated SWNT and biotin-streptavidin immobilization cases, the capacitances are $C_b=0.55\;pF$ and $C_s=0.95\;pF$. In this work, we experimentally demonstrated that the specific biomaterial binding causes the capacitance change and therefore this gives rise to resonant frequency. In conclusion, we confirmed the sufficient possibility as CNT biosensor because an analyte biomaterial(streptavidin) binding arouses a considerable resonant frequency change.

• Journal of Navigation and Port Research
• /
• v.31 no.5 s.121
• /
• pp.415-420
• /
• 2007

In this paper, we have designed and fabricated a new type of bandpass-filter that used rectangular ring and interdigital capacitive feeding-structure. The filter is applied the modified rectangular ring and interdigital capacitive feeding-structure in patch, which reduce rho size of filter and IEEE 802. 11 correspond to wireless LAN domain(2.45GHz and 5.2GHz) for operating. As a result, the design and fabrication process of the filter become simple and the size of it is reduced more than 60% compared with RF filter are available conventional PEMBF(Parallel Edge-coupled Microstrip Bandpass Filter) of accounted circuit by minimum stage, measurement result of fabricated filter, center frequence is down 2.408GHz and 5.075GHz. input return loss is -39.169dB at 2.408GHz, -40.922dB at 5.075GHz. insertion loss is -0.437dB at 2.408GHz, -1.669dB at 5.075GHz.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.2 no.2
• /
• pp.3-10
• /
• 1991

The new structure method of GaAs microwave amplifiers using DC block function and impedance transforming property of DC block/transformer(non-symmetrical two - microstrip coupled line and interdigital three - microstrip coupled line), instead of chip capacitor, is presented. The newly structured microwave amplifier showed wideband characteristics(bandwidth, 3.5 GHz) and flat frequency response. Interdigital three - microstrip coupled line which is used for microwave amplifier can be used to match amplifiers as well as DC blocking.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 2006.07a
• /
• pp.719-719
• /
• 2006

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2002.11a
• /
• pp.370-374
• /
• 2002

This paper describes the design and fabrication of distributed analog phase shifter circuit. The phase shifter consist of coplanar waveguide(CPW) lines that are periodically loaded with voltage tunable (Ba,Sr)TiO$_3$ thin film interdigital(IDT) capacitors deposited by the pulsed laser deposition(PLD) on (001) MgO single crystals. The phase velocity on these IDT loaded CPW lines is a function of applied bias voltage, thus resulting in analog phase shifting circuits. The measured differential phase shift is 48$^{\circ}$ and the insertion loss decreases from -5㏈ to -3㏈ with increasing bias voltage from 0 to 40 V at 100㎐.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.140-144
• /
• 2003

To investigate failure analysis of surface acoustic wave (SAW) filter for radio frequency, high temperature storage test was carried out. The failure criteria were insertion loss at passband and rejection level at stopband. As a result, the insertion loss at passband increase about 4 dB was due to damages of interdigital transducer (IDT). That is caused by poor adhesion between metal electrode(AI) and piezoelectric substrate and defects on a manufacturing process. This result indicates that good adhesion between electrode and ceramic substrate is important factor And also we investigated the demage factors of electrode. Screen possible of saw filter using high temperature storage test(HTOL) in the manufacturing phase be presented.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.4C no.6
• /
• pp.300-305
• /
• 2004

In this paper, new design equations based on the pole-zero analysis for multi-layered interdigital stripline linear group delay bandpass filter with tap input ports are presented. As a design example, a four-pole group delay filter with center frequency of 2.14GHz, bandwidth of 160MHz, and group delay variation of $\pm$0.1nS for LTCC technology or multilayered PCB technology is designed. In the design process, it is not necessary to simulate the entire structure, as the simulation of half structures is sufficient. Good results can be attained after the optimizing process was performed three times using the proposed equations and a commercial EM simulator.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.10
• /
• pp.1061-1067
• /
• 2004

In this study, ferroelectric (Ba,Sr)TiO$_3$ and high temperature superconductor YBCO thin films were fabricated by PLD (Pulsed Laser Deposition) method and tuneable bandstop filters were implemented with two different IDC(Interdigital Capacitance) gap patterns, 20${\mu}{\textrm}{m}$ and 30${\mu}{\textrm}{m}$ using these two thin film layers. The resonant frequency was changed by DC bias voltage. By comparing measured results with simulation, the dielectric properties of ferroelectric thin film have been extracted. The permittivity was 820 ～ 900 at 30 K and had an acceptable error range but the loss tangent had a great difference, 0.018 in 30${\mu}{\textrm}{m}$ IDC gap pattern and 0.037 in 20 ${\mu}{\textrm}{m}$.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.625-628
• /
• 2009

In the bistable chiral splay nematic (BCSN) mode, the splay and ${\pi}$ twist states are used for the two stable states. The switching property is strongly dependent on the amplitude of the electric field. In this paper, we investigated the gray scale capability of BCSN liquid crystal display (LCD) by the gradual horizontal electric field caused the interdigital electrode of by the inequality gap. We demonstrate the gray scale of the BCSN LCD during transition process under the horizontal electric field.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.1
• /
• pp.85-92
• /
• 2002

In this study, we analyzed and experimented micro-strip line inductors and capacitors for a SAW duplexer, an important devise for mobile communication. For SAW duplexers, micro-strip line lumped elements must have small impedance values, below several tens of nH or several tens of pF, and a small area pattern. In this study, we performed theoretical analysis of flat line type, meander line type, and spiral line type inductors and interdigital capacitors on a LiTaO$_3$ Piezo-crystal. We proposed a measurement method to evaluate small values of lumped elements accurately with network analyzer. In experiments, we confirmed validity of the theoretical analysis method through fabrication and characterization of micro-strip line lumped elements. The analysis method in this paper can be applied to SAW duplexers well as other microwave devices.