• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.2
• /
• pp.40-47
• /
• 2003

This paper presents a new evaporative system monitoring method using a virtual HC sensor for an automotive on-board diagnosis. A development was made at providing mathematical expressions from the lambda control information to estimate the HC mass flow purged into the intake manifold from the canister for implementing a virtual HC sensor. The change of the lambda averagevalue reflected the influence of the additional fuel from purging results the sensor estimation of the purged HC amount. Based on this virtual HC sensor, a new evaporative system monitoring method was proposed comparing the amount of purged HC amount with the amount of the HC gas evaporated from the fuel tank and absorbed into the canister. Finally, the method was validated with a simulation using the data logged from the retail car.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.2
• /
• pp.10-15
• /
• 2005

This study was initiated to evaluate the cooling performance of CAC (charged air cooler) and radiator in the engine room of a mini bus. So we had firstly to predict the mass flow rate coming from radiator grille and front bum per opening using computational fluid dynamics (CFD) simulation based on 3D configuration. And simulations were carried out for different cooling module layout and bum per opening hole size on sam e vehicle operating condition. Simulation results show that CAC cooling performance at reverse protecting plate-applying model was much efficient than that of the bum per opening hole size-increasing model in IMTD point of view. Part of the CFD simulation results was com pared to with experimental data. It was confirm ed that the CFD approach using STAR-CD based on pursuing no-com promise solution could provide design engineers with useful design information in the early design stage of vehicle development.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.8
• /
• pp.24-33
• /
• 1999

This paper investigate the effects of the variations of engine operation condition in the flame kernel formation and developmnet . A model for calculating the initial kernel development in spark ignition engines is formualted. It considered input of electrical energy, combustion energy release and heat transfer to the spark plyg, cylinder head, and unburned mixture. The model also takes into accounts strain rate of initial kernel and residual gas fraction. The breakdown process and the subsequent electrical power input initially control the kernel growth while intermediate growth is mainly dominated by diffusion or conduction. Then, the flame propagates by the chemical energy and turbulent flame expansion. Flame kernel development also influenced by engine operating conditions, for example, EGR rate, air-fuel ration and intake manifold pressure.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.38 no.9
• /
• pp.724-732
• /
• 1989

The structure of engine and its interaction are investigated and the construction of mathematical model for the performance evaluation is presented and then simulated. The total system is classified as air-fuel inlet element, intake manifold, combustion, and engine dynamics and their control function are schematically evaluated. Because of the model structure with general engine function and computer simulation of the chosen engine, physical characteristics of the corresponding engine and the engine data of normal operation state are used. According to the study, it is possible to predict the mixture rate by by the difference in the mass of fuel and air into cylinder and to evaluate and trace dynamic characteristic of operation state under various operating condition. The model characteristic under the transient operating condition makes it possible to effectively evaluate the operation of actual engine through the result of simulation.

• 한국연소학회:학술대회논문집
• /
• 2013.06a
• /
• pp.37-40
• /
• 2013

Hydrogen-dimethy ether (DME) and hydrogen-diesel compression ignition engine combustion were investigated and compared each other in a single cylinder compression ignition engine. Hydrogen and DME were used as low carbon alternative fuels to reduce green house gases and pollutant. Hydrogen was injected at the intake manifold with an injection pressure of 0.5 MPa at fixed injection timing, $-210^{\circ}CA$ aTDC. DME and diesel were injected directly into the cylinder through the common-rail injection system at injection pressure of 30 MPa. DME and diesel inejction timing was varied to find the optimum CI combustion to reduce CO, HC and NOx emissions. When DME was injected early, CO and HC emissions were high while NOx emission was low. Fuel consumption, heat release rate, and exhaust emissions were measured to analyze each combustion characteristics of each ignition promoter. Fuel consumption was decreased when diesel was used as an ignition promoter. This is due to the lower volatility of diesel which created more stratified charge than DME.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.3
• /
• pp.613-619
• /
• 2017

In this paper, DF(Dual Fuel) Generator modeling, which uses both conventional diesel fuel and LNG fuel, has been performed and monitoring system has been developed based on MATLAB/SIMULINK for the development of PMS(Power Management System) HILS(Hardware In the Loop Simulation). The principal components modeling of DF Generator are DF engine which provides the mechanical power and synchronous generator which convert the mechanical power into electrical power. Submodels, such as throttle body, intake manifold, torque generation and mass of LNG and diesel Quantity are used to perform DF engine. Also, governor is used for load sharing between paralleled DF generators to share a total load that exceeds the capacity of a single generator. To verify modeling of DF Generator designated ship lumped load Simulation is carried out. A validity of DF Generator has been verified by comparison between simulation results and estimated result from the designated lumped load.

• Journal of the Korean Institute of Gas
• /
• v.18 no.5
• /
• pp.47-51
• /
• 2014

This paper is to analyze and study the fire examples in respect of intake and exhaust, alternator tuning and inflow of inflammables on exhaust part in a car. In the first example, the driver diverted the intake and exhaust system for tuning of a car. Stopping a car to rest for moment, the flammable styrofoam scrap go into exhaust pipe that installed with exhaust manifold newly. It certified the fact that catched fire gradually, furthermore enlarged the fire by leaking fuel. In the second example, the driver enlarged the generator performance to divert the audio system in side room., it knew the fact that the electric wiring connected with generator gave the cause of outbreak a fire by overheating. In the third example, the serviceman replaced the engine oil using funnel-shaped, he put the a bottle of plastic pat onto engine cover carelessly. Consequentially, it found the fire occurrence in the engine room. Therefore, the driver never divert the intake and exhaust and generator construction of a car abnormally. Also, repairing and inspecting a car, the serviceman have a care to not occur the fire by inflammables.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.4
• /
• pp.133-138
• /
• 2009

The continued rise in the number of automobiles on the roads is prompting air pollution to emerge as a serious problem due to the harmful exhaust gas emissions throughout the world. Specifically, based on the exhaust gas regulation in North America represented by PZEV, the regulation on evaporative emission, which originates from the intake manifold system when the engine is stopped, is substantially being intensified. And the technology that can meet and satisfy these regulations has been needed. This study aimed to analyze and evaluate the butane working capacity (BWC) of HC adsorption filter according to the shape of it, which was developed to reduce evaporative emission, and the effect of HC adsorption filter on the engine performance. As a results, HC adsorption filter of the plate type, which was improved compared to that of the corrugated type and also became thinner, indicates higher absorption performance compared to the corrugated one. The absorption performance of the honeycomb type, derived from improving the shape of plate type, is 33.5% higher than that of the corrugated type. However, there was no significant difference in engine performance in all shapes.

• Journal of the korean Society of Automotive Engineers
• /
• v.8 no.3
• /
• pp.46-54
• /
• 1986

Driving pattern of gasoline passenger car was measured and analyzed at some areas(6urban area routes, 4 radial routes, 4 circular routes)in Seoul city. Measured items were vehicle speed, engine speed, intake manifold vacuum, and fuel consumption. Driving pattern data were reappearanced with engine dynamometer. Results of this investigation might be summarized as below; 1. When we compared urban area route with radial or circular route in rush hour, it was found that the average vehicle speed was measured to be lower about 25% and fuel consumption to be higher about 12% in urban area route. 2. Average vehicle speed was measured to be higher about 30% and driving resistance output to be higher about 25% in non-rush hour, but average fuel economy was increased a little. 3. On the bases of average fuel economy and characteristics of exhaust emissions, optimum driving vehicle speed was found about 60 km/h in the 4th(top)and about 40km/h in the 3rd in driving of experimental engine. 4. Idling frequency and exhaust emissions of CO,HC were related to idling closely. But exhaust emission of NOx, which had nothing to do with idling frequency, had relation to acceleration time ratio.

• Journal of the Korean Society of Combustion
• /
• v.18 no.1
• /
• pp.27-33
• /
• 2013

Hydrogen-dimethy ether(DME) partially premixed compression ignition(PCCI) engine combustion was investigated in a single cylinder compression ignition engine. Hydrogen and DME were used as low carbon alternative fuels to reduce green house gases and pollutant. Hydrogen was injected at the intake manifold with an injection pressure of 0.5 MPa at fixed injection timing, $-210^{\circ}CA$ aTDC. DME was injected directly into the cylinder through the common-rail injection system at injection pressure of 30 MPa. DME inejction timing was varied to find the optimum PCCI combustion to reduce CO, HC and NOx emissions. When DME was injected early, CO and HC emissions were high while NOx emission was low. As the DME injection was retarded, the CO and HC emissions were decreased due to high combustion efficiency. NOx emissions were increased due to the high in-cylinder temperature. When DME were injected at $-30^{\circ}CA$ aTDC, reduction of HC, CO and NOx emissions was possible with high value of IMEP.