• 한국농공학회지
• /
• 제22권2호
• /
• pp.64-82
• /
• 1980

The aim of this thesis, when water permeates dam, is to study the shape of seepage line and seepage quantity. As for the process, various sand model dams of same capacity were constructed in the water tank : they are a central, middle, inclined, up and down stream point of which is paralled, and filter-installed types. And the slope of seepage line and seepage quantity in these various models for experiment were measured, observed data were analyzed, and several formulas which already published were compared and examined. As for the shape of seepage line, the relation between upstream water level and exit: slope of seepage line, near the entrance and exit point, geometrically similar model, and the shape of seepage line filter-installed were examined. As regards to the seepage quantity, several formulas which already published and testing result values were compared and examined, and relation with the slope of seepage line, the seepage quantity, the slope of upstream point, and the upstream water level were mutually studied. Particulary, when horizontal filter was installed, propriety of the existing formulas for effective filter length w as examined, and the relative position of exit point in various. conditions was also studied.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.498-503
• /
• 2005

This paper is concerned with the implementation of adaptive positive position feedback controller using a digital signal processor and microcontroller The main advantage of the positive position feedback controller is that it can control a natural mode of interest by tuning the filter frequency of the positive position feedback controller to the natural frequency of the target mode. However, the positive position feedback controller loses its advantage when mistuned. In this paper, the fast fourier transform algorithm is implemented on the microcontroller whereas the positive position feedback controller is implemented on the digital signal processor. After calculating the frequency which affects the vibrations of structure most the result is transferred to the digital signal processor. The digital signal processor updates the information on the frequency to be controlled so that it can cope with both internal and external changes. The proposed scheme was installed and tested using a beam equipped with piezoceramic sensor and actuator. The experimental results show that the adaptive positive position feedback controller proposed in this paper can suppress vibrations even when the target structure undergoes structural change thus validating the approach.

• 한국생산제조학회지
• /
• 제24권2호
• /
• pp.141-147
• /
• 2015

In this study, a position control algorithm for an omni-directional mobile robot based on Mecanum wheels was introduced and experimentally evaluated. Multiple ultrasonic sensors were installed around the mobile robot to obtain position feedback. Using the distance of the robot from the wall, the position and orientation of the mobile robot were calculated. In accordance with the omni-directional velocity generation mechanism, the velocity kinematics between the Mecanum wheel and the mobile platform were determined. Based on this formulation, a simple and intuitive position control algorithm was suggested. To evaluate the control algorithm, a test bed composed of artificial walls was designed and implemented. While conventional control algorithms based on normal wheels require additional path planning for two-dimensional planar motion, the omni-directional mobile robot using distance sensors was able to directly follow target positions with the simple proposed position feedback algorithm.

• 한국도로학회논문집
• /
• 제15권1호
• /
• pp.155-161
• /
• 2013

PURPOSES: This study is to develop a road traffic sign recognition and automatic positioning for road facility management. METHODS: In this study, we installed the GPS, IMU, DMI, camera, laser sensor on the van and surveyed the car position, fore-sight image, point cloud of traffic signs. To insert automatic position of traffic sign, the automatic traffic sign recognition S/W developed and it can log the traffic sign type and approximate position, this study suggests a methodology to transform the laser point-cloud to the map coordinate system with the 3D axis rotation algorithm. RESULTS: Result show that on a clear day, traffic sign recognition ratio is 92.98%, and on cloudy day recognition ratio is 80.58%. To insert exact traffic sign position. This study examined the point difference with the road surveying results. The result RMSE is 0.227m and average is 1.51m which is the GPS positioning error. Including these error we can insert the traffic sign position within 1.51m CONCLUSIONS: As a result of this study, we can automatically survey the traffic sign type, position data of the traffic sign position error and analysis the road safety, speed limit consistency, which can be used in traffic sign DB.

• 한국인터넷방송통신학회논문지
• /
• 제15권1호
• /
• pp.199-205
• /
• 2015

많은 사용자가 항상 휴대하는 스마트폰을 대상으로 실내에서의 위치 인식을 위한 기술 개발이 매우 활발하다. 특히 음향 신호를 이용한 TDOA 방식의 위치 측정 시스템도 많이 연구되고 있는데, 이 방식은 스마트폰의 스피커와 음향 신호를 수신하기 위한 위치 측정 장치에 설치된 마이크들 사이의 거리를 측정하고 관련 쌍곡선 수식을 계산하여 스마트폰의 위치를 추정하는 것이다. 그러나 스피커와 각 마이크 사이의 거리를 측정하는 것에 항상 오차가 있고, 게다가 위치 측정 장치에 설치된 음향 센서인 마이크의 설치 위치 오차에 따라서 위치 측정 오차가 매우 크게 발생한다. 본 논문에서는 3차원 TDOA 위치 측정 시스템에서 음향 센서의 위치 오차에 따른 위치 측정 오차가 PDOP 시뮬레이션과 실험으로 분석되었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권5호
• /
• pp.730-736
• /
• 2008

The purpose of this study is to find out a flow characteristics when a crossflow-fan is installed inside the computer case and to provide information about the preliminary data of cooling efficiency of CPU and a flow inside and outside of a computer case. Under the condition of operating the fan inside the experimental duct we changed the position of a installation of the slot, and the experiment measured with PIV and the results are as follows. Under the influence of the crossflow-fan installed to the air discharging side, mean velocity between 35 to 45 on the point 80 of the Slot 0.2.3 of the case increased and it influences discharging the air inside of the computer case. On the left-upper end. which isn't directly influenced by the suction-discharging fan installed inside the PC, a flow occurs caused by vortex due to the Sirocco-Fan and Slot installed on the center of the right side. We can see that a flow distribution increases when the Sirocco-Fan operates and a whirl appears stronger between the slot and the suction fan. It is thought that this phenomenon is influenced by a flow while it is on the way of entering from the suction-fan and going out to the discharging-fan.

• 설비공학논문집
• /
• 제19권12호
• /
• pp.811-820
• /
• 2007

A Study on the optimal design of the AIG(Ammonia Injection Grid) to improve the performance of DeNOx facilities in the HRSG(Heat Recovery Steam Generator) was performed using the CFD analysis. On the basis of the flow analysis results in the case that the AIG in the HRSG was not installed, the numerical analyses according to the positions of AIG, injection angles of nozzle and the control of ammonia injection quantity were carried out. The standard deviation according to factors was calculated for quantitative comparison. As the results, the AIG in the HRSG should be installed in the position that the uniform flow field shows through the exact flow analysis in the previous of the AIG design and installation. In the case the AIG has already been installed and non uniform flow distribution shows, it is recommended that flow correction device or KoNOx catalyst should be used. Otherwise, the control of ammonia injection angle or the ammonia injection quantity using the velocity profile analysis is demanded to accomplish the optimal performance.

• Smart Structures and Systems
• /
• 제26권5호
• /
• pp.575-589
• /
• 2020

For vibration control of stay cables in cable-stayed bridges, viscous dampers are frequently used, and they are regularly installed between the cable and the bridge deck. In practice, neoprene rubber bushings (or of other types) are also widely installed inside the cable guide pipe, mainly for reducing the bending stresses of the cable near its anchorages. Therefore, it is important to understand the effect of the bushings on the performance of the external damper. Besides, for long cables, external dampers installed at a single position near a cable end can no longer provide enough damping due to the sag effect and the limited installation distance. It is thus of interest to improve cable damping by additionally installing dampers inside the guide pipe. This paper hence studies the combined effects of an external damper and an internal damper (which can also model the bushings) on a stay cable. The internal damper is assumed to be a High Damping Rubber (HDR) damper, and the external damper is considered to be a viscous damper with intrinsic stiffness, and the cable sag is also considered. Both the cases when the two dampers are installed close to one cable end and respectively close to the two cable ends are studied. Asymptotic design formulas are derived for both cases considering that the dampers are close to the cable ends. It is shown that when the two dampers are placed close to different cable ends, their combined damping effects are approximately the sum of their separate contributions, regardless of small cable sag and damper intrinsic stiffness. When the two dampers are installed close to the same end, maximum damping that can be achieved by the external damper is generally degraded, regardless of properties of the HDR damper. Field tests on an existing cable-stayed bridge have further validated the influence of the internal damper on the performance of the external damper. The results suggest that the HDR is optimally placed in the guide pipe of the cable-pylon anchorage when installing viscous dampers at one position is insufficient. When an HDR damper or the bushing has to be installed near the external damper, their combined damping effects need to be evaluated using the presented methods.

• 수산해양기술연구
• /
• 제29권1호
• /
• pp.21-29
• /
• 1993

한국의 연안어선에 장비된 소형자기컴퍼스의 장비현황과 성능을 연구하기 위하여 소형어선 219척의 선박제원과 자기컴퍼스 이용에 대한 현장 설문조사를 행하고, 그 중에서 총톤수 4-6톤급의 실험대상 어선 4척을 선정하여 그 선박의 자기컴퍼스의 설치위치별 자차측정과 성능실험을 행하고, 이를 검사, 조사하였다. 주요한 결과를 요약하면 다음과 같다. 1. 조사 대상으로 한 총톤수 1-10 톤급 연안어선 219척 중 4톤 미만의 어선은 약 50%를 차지하였고, 자기컴퍼스의 제작연도가 20-30년 경과된 어선이 14척이나 되었으며, 자차수정용구를 비치한 어선은 2척 뿐이었다. 2. 컴퍼스의 설치위치별로 측정된 자차를 분석한 결과, 기관실위의 브리지갑판상과 브리지내의 컴퍼스받침대위 및 브리지위의 컴퍼스 갑판상에 자차수정을 한 자기컴퍼스를 설치하여 사용하면, 브리지내의 컴퍼스대의 위와 브리지위의 컴퍼스 갑판상에서는 잔재자차가 $\pm$1~2 $^{\circ}$ 정도였으나, 기관실 위의 브리지갑판상에서는 그 잔재자차가 $\pm$5 $^{\circ}$로 이곳은 컴퍼스 설치 장소로서 부적당함을 알 수 있었다. 3. 연안어선에서 사용 중인 자기컴퍼스의 제반특성은 표준규격인 반주기의 평균치가 12초 이상이어야 하고, 3회 이상 진동해야하는 기준에 미달하였으며, 측정치인 자기능률 1400 CGS는 소형컴퍼스의 표준치 400$\pm$30 CGS와는 큰 차이가 있었다. 4. 실험 대상 어선에 장비하고 있는 자기컴퍼스의 수반각은 6~16 $^{\circ}$로서 한국표준규격인 1~1.5 $^{\circ}$에 비해 너무 크게 나타나 그 표준규격에 부적합한 것으로 판단되었다.

• 동력기계공학회지
• /
• 제15권5호
• /
• pp.91-96
• /
• 2011

The handling ability of containers at the terminal strongly depends on the performance of the cargo handling system such as RTGC(Rubber Tired Gantry Crane) and RMGC(Rail Mounted Gantry Crane). This paper introduces a guide line measurement system on the operating condition, in which two camera are installed to detect the guide line. Because the line tracking is the basic technique for control system design of RTGC, it is necessary to develop a useful and reliable measurement system. If the displacement and angle of the RTGC relative to a guide line as the trajectory to follow is obtained, the position of RTGC is automatically calculated. Therefore, in this paper, a camera-based measurement system is introduced. The proposed measurement system is robust against light fluctuation and cracks of the guide line. This system consists of two camera and a PC which are installed at the lower side of the RTGC. Two edges of the guide line are detected from an input image taken by the cameras in the moving state, and these positions are determined in a Hough parameter space by using the Hough transformation method. From the experimental results, the accuracy and usefulness of the proposed system is evaluated by comparing other instruments.