• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.2
• /
• pp.18-28
• /
• 1989

In this paper, we describe a pointing accuracy establishment and efficiency measurement of 13.7 m antenna for observing cosmic radio wave which is in the first stage just after finishing its installation. The initial stage of pointing model, 1 and 2 were set up with the observational data of Sun and Moon which are large in visual diameter and also strong in radio intensity. Based on this model, model 3 and 4 were established within the available operational range, i.e., 3.8" in azimuth deviation, 10.5" in elevation deviation, with the observational data of SiO maser source which is a point source and distributed in overall sky. Both apeture efficiency anhd beam efficiency were measured by observing Venus whose brightness temperature is well-known. The resulting corrected efficiencies were 35% and 50% respectively.

• Journal of the Korean Institute of Gas
• /
• v.20 no.2
• /
• pp.66-71
• /
• 2016

Nowadays, a number of sensors which are placed in industrial complex are monitoring areas involving chemical leak and other faults. However, even in the presence of the sensors, chemical leaks, sometimes involving huge amount of chemicals, continuously led to big losses in the industrial complex. In most industries, sensor installation has been performed using past experience or using senor manufacturers' guideline; which leads to poor performance of the installed sensor grid. Therefore, we investigate an optimal placement methodology of point sensors for rapid detention and response when chemical leaks happen. This research suggests a generalized formulation suitable for the optimized decision making of minimizing number of sensors to be placed and increasing the fraction of covered scenarios under assumption of negligible effect of other structures. The proposed method has been verified for suitable performance for simple leak scenario simulations, by achieving the safety objectives and guaranteeing safe process operations.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.185-188
• /
• 2001

Chemical mechanical polishing(CMP) process is widely used for global planarization of inter-metal dielectric (IMD) layer and inter-layer dielectric (ILD) for deep sub-micron technology. However, as the IMD and ILD layer gets thinner, defects such as micro-scratch lead to severe circuit failure, which affect yield. In this paper, for the improvement of CMP process, deionized water (DIW) pressure, purified $N_2 \; (PN_2)$ gas, slurry filter and high spray bar were installed. Our experimental results show that DIW pressure and $PN_2$ gas factors were not related with removal rate, but edge hot-spot of patterned wafer had a serious relation. Also, the filter installation in CMP polisher could reduce defects after CMP process, it is shown that slurry filter plays an important role in determining consumable pad lifetime. The filter lifetime is dominated by the defects. However, the slurry filter is impossible to prevent defect-causing particles perfectly. Thus, we suggest that it is necessary to install the high spray bar of de-ionized water (DIW) with high pressure, to overcome the weak-point of slurry filter. Finally, we could expect the improvements of throughput, yield and stability in the ULSI fabrication process.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.3
• /
• pp.18-24
• /
• 2016

This study presents a simple method which can estimate displacement using measured strain response of simply supported girder bridges. The basic concept of the present method is derived from a relation between displacement and strain, and is generalized by introducing analytical tool. Static and dynamic laboratory test are conducted on simply supported plate which is designed to respond dynamically similar to actual bridges to experimentally verify the present method, and displacement and strain are measured at the midpoint of specimen. Displacement estimated by using measured strain is well agreed with measured one. This study demonstrates that the present method is suitable for estimating displacement of real simply supported bridge, in which the installation of a displacement transducer at the fixed reference point is difficult.

• International Journal of Fluid Machinery and Systems
• /
• v.2 no.4
• /
• pp.392-399
• /
• 2009

The paper concerns the description of the step by step development process of the new fixed blade runner called "Mixer" suitable for the uprating of the Francis turbines units installed at the older low head hydropower plants. In the paper the details of hydraulic and mechanical design are presented. Since the rotational speed of the new runner is significantly higher then the rotational speed of the original Francis one, the direct coupling of the turbine to the generator can be applied. The maximum efficiency at prescribed operational point was reached by the geometry optimization of two most important components. In the first step the optimization of the draft tube geometry was carried out. The condition for the draft tube geometry optimization was to design the new geometry of the draft tube within the original bad draft tube shape without any extensive civil works. The runner blade geometry optimization was carried out on the runner coupled with the draft tube domain. The blade geometry of the runner was optimized using automatic direct search optimization procedure. The method used for the objective function minimum search is a kind of the Nelder-Mead simplex method. The objective function concerns efficiency, required net head and cavitation features. After successful hydraulic design the modal and stress analysis was carried out on the prototype scale runner. The static pressure distribution from flow simulation was used as a load condition. The modal analysis in air and in water was carried out and the results were compared. The final runner was manufactured in model scale and it is going to be tested in hydraulic laboratory. Since the turbine with the fixed blade runner does not allow double regulation like in case of full Kaplan turbine, it can be profitably used mainly at power plants with smaller changes of operational conditions or in case with more units installed. The advantages are simple manufacturing, installation and therefore lower expenses and short delivery time for turbine uprating.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.2A
• /
• pp.181-186
• /
• 2004

Analysis on sharing between GSO FSS and terrestrial system in the 40㎓ band, related with the problem for sharing between terrestrial services and FSS and identification of HDFSS downlink bands in World Radiocommunication Conference 2003, was practiced by assuming that both systems are operated in Korea. According to results from simulation using the characteristic parameters of GSO FSS and terrestrial FS system in 40 ㎓ described in ITU-R Recommendations, in case that elevation and azimuth angle of antenna of FS station are adjusted to point directly to the geostationary satellite, the GSO system can cause the worst interference to the FS system. This situation is possible to occur in the installation of 40 GHz FS station in urban area where there are high-rise buildings. If high-density FS stations in 40 ㎓ band are operated in the future, interference mitigation techniques to avoid GSO arc should be considered.

• Journal of KIISE:Software and Applications
• /
• v.32 no.12
• /
• pp.1238-1246
• /
• 2005

This thesis is written with web security module for safe data transmission between heterogeneous systems(ex. OS). Web system has allowed users to have great convenience and a lot of information. Though web service business has been progressed much, because of the limitation of it's own system, lots of loss, derived from data spillage which is the weakest point of security, has also followed. Suggested security module is realized by two module. One for server security module for web server, the other is client security module for client. The security structure, suggested on this thesis guarantee safe data transmission by only simple installation of modules in clients and servers. for speed sensitive transmission between web server and browser, Triple-DES, symmetric encryption system suitable for fast encryption communication, is adapted. To solve problems caused from key management, Diffie-Hellman's key exchange algorithm is adapted. By this method, all symmetric encryption troubles from key distribution and management, speed could be work out a solution. And Diffie-Hellman type algorithm secures Authentication for safe data Protection.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2009.03a
• /
• pp.308-319
• /
• 2009

In the case of relatively good ground and construction condition in the deep excavation for the construction of subway, railway, building etc., flexible earth retaining systems are often used in an economical point of view. It is generally known that the mechanism of behavior in the flexible earth retaining system is relatively more complicated than the rigid earth retaining system. Moreover in the case of long span strut supporting system the analysis of strut axial force change becomes more difficult when the differences of ground condition and excavation work progress on both sides of excavation section are added. When deeper excavation than the specification or installation delay of supporting system is done or change of ground condition is faced due to the construction conditions during construction process, lots of axial force can be induced in some struts and that can threaten the safety of construction. This paper introduces two examples of long span deep excavation where struts and rock bolts were used as a supporting system with flexible wall structure. And the sections of two examples are 50 meters apart in one construction site, they have almost similar design and construction conditions. The characteristics of ground deformation and strut axial force change were analysed, the similarity and difference between measurement results of tow examples were compared and investigated. The effort of this article aims to improve and develop the technique of design and construction in the coming projects having similar ground condition and supporting method.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.1
• /
• pp.64-71
• /
• 2006

For SUAV is required to have the capacity of VTOL and fast forward flight, the SUAV development program has decided to adopt the tiltrotor mechanism which includes helicopter and turboprop mechanisms. From the engine point of view, the key engine parameters such as engine operating mechanism, engine control scheme, the dynamics characteristic of power train, engine intake/exhaust concept, and engine installation requirements should fulfill the requirements of the two different mechanisms, helicopter and turboprop. And for the maximum efficiency of the rotor, rotational speed for the two modes are 20% different, the power train shall find a way to make it so. Meeting these specific requirements for the tiltrotor mechanism, this research begins with a conventional OTS(off-the-shelf) turboshaft engine survey and minimizes engine modification to develop an economical propulsion system. The engine technical review has been performed on the basis of those requirements and capabilities.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.4
• /
• pp.91-96
• /
• 2018

Recently, as artificial intelligence technology becomes popular, demand for wireless traffic is rapidly increasing. In order to provide services in response to the increase in demand for wireless traffic, telecommunication companies are generalizing the installation of public APs. In order to provide convenience of using wireless APs between communication companies, it is necessary to share the use of APs in public places to efficiently use wireless resources in a public place, to pre-authenticate between wireless APs in a mobile communication service, So as to increase the convenience of the user. In this paper, we propose to share APs in public places through handoff between APs and pre-authentication between carriers in mobile communication services. The simulation results show that the handoff latency is improved by 35.1% and the bandwidth used by the AP selected by the pre-authentication method can utilize more bandwidth than the method of automatically selecting the AP.