• Geomechanics and Engineering
• /
• 제23권6호
• /
• pp.523-533
• /
• 2020

The current study focuses on the effect of the end shape of steel pipe piles on installation effort and bearing resistance using the pressing method of installation under dense ground conditions. The effect of pile rotation on the installation effort and bearing resistance is also investigated. The model steel piles with a flat end, cone end and cutting-edge end were used in this study. The test results indicated that cone end pile with the pressing method of installation required the least installation effort (load) and showed higher ultimate resistance than flat and cutting-edge end piles. However, pressing and rotation during cutting-edge end pile installation considerably reduces the installation effort (load and torque) if pile penetration in one rotation equal to the cutting-edge depth. Inclusion of rotation during pile installation reduces the ultimate bearing resistance. However, if penetration of the cutting-edge end pile equal to the cutting-edge depth in one rotation, the reduction in ultimate resistance can be minimized. In comparing the cone and cutting-edge end piles installed with pressing and rotation, the least installation effort is observed in the cutting-edge end pile installed with penetration rate equal to the cutting-edge depth per rotation.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.561-568
• /
• 2005

The factors affecting the long-term design strength of geogrid can be classified into factors on creep deformation, installation damage, temperature, chemical degradation and biological degradation. Especially, creep deformation and installation damage are considered as main factors to determine the long-term design strength of geogrid. Current practice in the design of reinforced soil is to calculate the long-term design strength of a reinforcement damaged during installation by multiplying the two partial safety factors, $RF_{ID} and RF_{CR}$. This method assumes that there is no synergy effect between installation damage and creep deformation of geogrids. Therefore, this paper describes the results of a series of experimental study, which are carried out to assess the combined effect of installation damage and creep deformation for the long-term design strength of geogrid reinforcement. The results of this study show that the tensile strength reduction factors, RF, considering combined effect between installation damage and creep deformation is less than that calculated by the current design method.

• 한국지반공학회논문집
• /
• 제21권5호
• /
• pp.153-161
• /
• 2005

시공 시 손상 및 크리프 변형의 복합효과가 지오그리드의 장기설계인장강도에 미치는 영향을 평가하기 위하여, 세 종류의 지오그리드를 대상으로 일련의 현장 내시공성시험 및 크리프시험을 수행하였다. 연구결과, 지오그리드의 시공시 손상 및 크리프 변형 특성은 지오그리드의 재질 및 제조방법에 크게 영향을 받으며, 시공 중 지오그리드의 인장강도감소가 클수록, 시공 시 손상과 크리프 변형의 복합효과가 미치는 영향이 더 큰 것으로 나타났다. 또한 지오그리드의 인장강도 감소계수를 영향인자별로 각각 산정하여 장기설계인장강도를 평가하도록 되어 있는 현행 설계법은, 지오그리드의 시공 시 손상과 크리프 변형의 복합효과를 고려하여 강도감소계수를 산정하는 방법에 비해 지오그리드의 강도감소계수를 안전측으로 산정하는 것으로 평가되었다.

• 대한안전경영과학회지
• /
• 제22권1호
• /
• pp.33-44
• /
• 2020

This study analyzed how the installation of a pressure gauge in the indoor fire hydrant of an apartment building affected identifying pressurized water in the pipe, making it easier to conduct internal inspection on the fire suppression system, and ensuring reliability of fire suppression. The following are the study's results: First, identifying pressurized water in the indoor firefighting pipe had a positive effect on the installation of a pressure gauge in the indoor fire hydrant. This implies that a higher level of identification of pressurized water in the indoor firefighting pipe had a positive impact on improving the installation and use of a pressure gauge in the indoor fire hydrant. Second, making it easier for the fire safety officer to inspect the fire suppression system had a positive effect on the installation of a pressure gauge in the indoor fire hydrant. This suggests that if it becomes easier for the apartment building's stakeholder to conduct internal inspection or the firefighting facility manager to carry out inspection on the fire suppression system, it would have a positive effect on the installation of a pressure gauge in the indoor fire hydrant. Finally, ensuring reliability in fire suppression had a positive effect on the installation of a pressure gauge in the indoor fire hydrant. This implies that if it becomes easier to identify pressurized water in the indoor firefighting pipe, for the fire safety officer to conduct internal inspection, or for the firefighting facility manager to carry out inspection in accordance with the fire suppression system's internal inspection requirements, it would increase reliability in fire suppression, making it more necessary to install a pressure gauge in the indoor fire hydrant.

• 한국도로학회논문집
• /
• 제20권1호
• /
• pp.127-135
• /
• 2018

PURPOSES : Traffic cameras have been installed to reduce traffic accidents. The effectiveness of traffic cameras has been proved by dozens of studies, but recently questions over its effectiveness have been raised by a series of studies. In this study, the effectiveness of traffic cameras was analyzed with a focus on different road environments. METHODS : The effectiveness of the traffic cameras was analyzed by extracting the occurence frequency before and after camera installation. The effect of reduction was analyzed comprehensively considering the installation position, monitoring direction, and surrounding environment of traffic cameras. RESULTS : The result of this study is as follows. First, the installation of cameras in an area with relatively low accidental traffic was more effective. Secondly, the effect of camera installation on car-to-pedestrian collisions was better than that of car-to-car collisions. Thirdly, accidents tended to occur more frequently when cameras were installed in front of the accident-prone owing to the negative spill-over effect. CONCLUSIONS : The result can be used to guide placement of traffic cameras. Moreover, the installation of cameras with consideration of the road environment is expected to contribute to a reduction in traffic fatalities.

• 대한교통학회지
• /
• 제12권1호
• /
• pp.137-149
• /
• 1994

The objective of study is to evaluate the effect of speed control hump on traffic operation and accidents. Three sites were investigated for the change of traffic accidents before and after the hump installation. Vehicle speeds approaching the hump were also analyzed. The study revealed that not only the number of traffic accidents but also the accident severity were significantly reduced by the installation of hump. Further, different types of traffic accidents with lower severity were observed after the hump installation. For the effect of speed reduction by hump, it was found that the speeds observed at 15m upstream of hump were in the range of 36~50 percent of approaching speeds which were not affected by (ie, without) the hump. Economic analysis of hump installation showed the benefit-cost ratio of 4.3 and 11.2 at two sites. Further analysis revealed that the benefit by the accident reduction exceeds the cost by speed reduction and installation capital if AADT is below 43,150 vehicles on two lane highways. It is recommended from the study that humps should be considered on two lane highways of high accident locations for excessive speeds to reduce traffic accidents and severity.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2002년도 학술대회논문집
• /
• pp.349-354
• /
• 2002

A size of low-voltage conductor cables is determined by the voltage drop of a system, the cable impedance and the cable ampacity based on temperature correction factor in accordance with the condition of cable installation. Therefore, the proper temperature correction factor according to the condition of cable installation should be applied to determining the cable ampacity and also the skin effect and proximity effect, along with the kind and size of conductor and the condition of cable installation, should be properly considered to analyze the proper value of resistance and the reactance of the conductors. This paper addresses the systematic design flow for determining the size of low voltage level conductor cables in calculating the temperature character where error should be minimized in comparison with the general formula and which can be applied in design work for determining the size of conductor cables.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 추계학술대회 논문집
• /
• pp.1156-1161
• /
• 2004

The factors affecting the long-term design strength of geogrid for railroad reinforcement can be classified into factors on creep deformation, installation damage, temperature, chemical degradation, biological degradation. Especially, creep deformation and installation damage are considered as main factors to determine the long-term design strength of geogrid. This paper describes the results of a series of experimental study, which are carried out to assess the combined effect of installation damage and creep deformation for the long-term design strength of geogrid reinforcement. In this study, a series of field tests are carried out to assess installation damage of a various geogrids according to different fill materials, and then creep tests are conducted to assess the creep properties of both undamaged and damaged geogrids.

• 한국조명전기설비학회지:조명전기설비
• /
• 제1권1호
• /
• pp.29-31
• /
• 1987

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2009년도 춘계학술대회 논문집
• /
• pp.211-213
• /
• 2009

Derivation of the phase error of hologram due to imperfection of a wave plate and analysis of the effect of phase error on 3-D image reconstruction of hologram are prexented.