• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.6
• /
• pp.767-781
• /
• 2013

In this paper, we proposes the AC input voltage and current sensorless control scheme to control the input power factor and DC output voltage of the three-phase Z-source PWM rectifier. For DC-link voltage control which is sensitive to the system parameters of the PWM rectifier, fuzzy-PI controller is used. Because the AC input voltage and current are estimated using only the DC-link voltage and current, AC input voltage and current sensors are not required. In addition, the unity input power factor and DC output voltage can be controlled. The phase-angle of the detected AC input voltage and estimated voltage, the response characteristics of the DC output voltage according to the DC voltage references, the FFT results of the estimated voltage and current, efficiency, and the response characteristics of the conventional PI controller and fuzzy-PI controller are verified by PSIM simulation.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.05a
• /
• pp.492-496
• /
• 2004

When using a conventional power factor correction circuit, a comparatively huge capacitor is used to boost-up output voltage. It has a large amount of harmonic distortion in the input current waveform. To improve the input current waveform of diode rectifiers, we propose a new operating principle for the power factor correction circuit. Due to the fact that the proposed circuit uses smaller ones and a smaller reactor, the output voltage increases and obtains higher input current waveforms. These are suitable for the harmonics guidelines. The proposed circuit is able to obtain higher power factor and efficiency. Also, it has reduced switching loss and held over-shooting by using an inverter of eliminated dead-time HPWM that has non-linear impedance circuits to make up diodes, capacitance and a reactor. We compared the conventional PWM inverter and proposed HPWM inverters and found that a high input power factor of 97[%] and an efficiency of 98[%] were also obtained.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.4
• /
• pp.461-468
• /
• 2014

An efficiency test for generators is generally required in case of construction of a new power plant or replacement of an existing generator. Generally, the efficiency of generator is measured by the input-output ratio under any given condition. Therefore, the best way is to directly measure the value of input and output power of a generator and calculate the efficiency values. However, it is difficult to measure a generator's input values accurately, especially for large systems. So, we are usually measuring the losses of the generator. But for measuring these values, there are several constraints for test such as preparing additional power generator and releasing the protection relay for manual operation of auxiliary equipments. Therefore, this study suggests that a novel generator efficient test method using the shaft-torque method which can be carried out while the generator is normally operating. The reliability of the result value was verified by comparing with the efficiency test results of the conventional retardation method on IEEE Std 115-1995.

• Journal of the Optical Society of Korea
• /
• v.13 no.1
• /
• pp.123-130
• /
• 2009

In this paper, we designed and fabricated an input-output coupler system using two or three volume gratings at 632.8nm wavelength. The additional third grating is added at the output coupler to enhance the overall efficiency. The experimental results show that the total system throughput reaches 63% with two-grating and 75% with three-grating input-output coupler. We also present a design method to obtain the desired output power ratio between the gratings.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.708-712
• /
• 2001

A new phase-shifted parallel-input/series-output (PI SO) dual inductor-fed push-pull converter for high-power step­up applications is proposed. This converter is operated at a constant duty cycle and employs an auxiliary circuit to control the output voltage with a phase-shift between the two modules. It features a voltage conversion characteristic which is linear to changes in the control input, and high step-up ratio with a greatly reduced switch turn-off stress resulting in a significant increase in the converter efficiency. It also shows a low ripple content and low root-mean-square (RMS) current in the output capacitor. The operational principle is analyzed and a comparative analysis with the conventional pulse-width-modulated (PWM) PISO dual inductor-fed push-pull converter is presented. A 50kHz, 800W, 350Vdc prototype with an input of 20-32Vdc has also been constructed to validate the proposed converter. The proposed converter compares favorably with the conventional counterpart and is considered well suited to high-power step-up applications.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.400-402
• /
• 2008

A new interleaved forward converter, adopting series-input parallel-output structure with a common transformer reset circuit, is proposed in this paper. Series-input structure distributes the voltage stress on switches, which makes it suitable for high input voltage application. Paralleling output stage with an interleaving technique enables the circuit handle large output current and reduces filter size. In addition, since two forward converters share one active-clamp circuit for the transformer reset, its primary structure is simplified. All these features make the proposed converter promising for high input voltage applications with high efficiency and simple structure.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.439-441
• /
• 2005

A new LLC resonant converter with multiple outputs is proposed for high efficiency and low cost plasma display panel (PDP) power module. In the proposed converter, ZVS turn-on of the primary MOSFETs and ZCS nun-off of the secondary diodes are guaranteed in the overall input voltage and output load range. Moreover, the primary MOSFETs and the secondary diodes have low voltage stresses clamped to input and the output voltage, respectively. Therefore, the proposed converter shows the high efficiency due to the minimized switching and conduction losses. In addition, by employing the transformer, which has the two and more secondary side, the proposed converter can have multiple outputs and they show the great cross-regulation characteristics. As a result, the proposed converter can be implemented with low cost and compact size. The 500W prototype is implemented, which integrates the sustaining and addressing power supplies of PDP power module. The maximum efficiency is 96.8% and the respective output voltages are well regulated. Therefore, the proposed converter is suitable for high efficiency and low cost PDP power module.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.1
• /
• pp.91-102
• /
• 2013

This paper proposes the improved LCCT(Inductor-Capacitor-Capacitor-Trans) Z-source DC-DC converter (Improved LCCT ZSDC) which can generate the bipolar output voltages according to duty ratio D. The proposed converter has the characteristic and structure of Quasi Z-source DC-DC converter(Quasi ZSDC) and conventional LCCT Z-source DC-DC converter(LCCT ZSDC). To confirm the validity of the proposed method, PSIM simulation and a DSP based experiment were performed for each converter. In case which the input DC voltage is 70V, the bipolar output DC voltage of positive 90V and negative 50V could generate. Also, as comparison result of the capacitor voltage ripple in Z-network and the input current under the same condition for each converter, the voltage stress and the capacitor voltage in Z-network of the proposed method were lower compared with the conventional methods. Finally, the efficiency for each method was investigated according to load variation and duty ratio D.

• Journal of Internet Computing and Services
• /
• v.9 no.2
• /
• pp.15-23
• /
• 2008

This paper proposes the new structural MOQ(Multiple Input/Output-Queued) switch which guarantees QoS while maintaining high efficiency and deals with the Anti-Empty algorithm which is new arbitration algorithm to be used for the proposed switch. The new structure of the proposed switch based on MIQ, MOQ is designed to have the same buffer speed as the external line speed. Also, the proposed switch makes it possible to remove the weak point of existing methods and introduces the new method of the MOQ operation to support QoS. Therefore, this switch is equal to the Output Queued switch in efficiency and delay, and guarantees the high-speed switching supporting QoS without cell loss.

• Journal of Technology Innovation
• /
• v.11 no.2
• /
• pp.151-173
• /
• 2003

This paper analyses the efficiency and productivity of R&D system across time (1991${\sim}$2000) and 16 OECD countries using multi-output and multi-input non-parametric frontier methods such as DEA (data envelopement analysis) and Malmquist productivity indexes. Malmquist productivity indexes are decomposed into two components measures, namely technical change and efficiency change. To calculate R&D efficiency and productivity, we used R&D stock and the number or researchers as R&D input proxies and the number of adjusted SCI papers and U.S. patent applications as R&D output proxies. Empirical result shows that Switzerland, Canada, U.S., Australia's R&D efficiencies are the highest and Korea's R&D productivity growth is the highest in the sample for the period. Technical efficiency growth was a more important source of productivity growth than technological innovation.