• Tribology and Lubricants
• /
• 제32권4호
• /
• pp.107-112
• /
• 2016

This paper presents a rotordynamic analysis of the reduction gear system applied to the 250 kW super critical CO₂ cycle. The reduction gear system consists of an input shaft, intermediate shaft, and output shaft. Because of the high rotating speed of the input shaft, we install tilting pad bearings, rolloer bearings support the intermediate and output shafts. To predict the tilting pad bearing performance, we calculate the applied loads to the tilting pad bearings by considering the reaction forces from the gear. In the rotordynamic analysis, gear mesh stiffness results in a coupling effect between the lateral and torsional vibrations. The predicted Campbell diagram shows that there is not a critical speed lower than the rated speed of 30,000 rpm of the input shaft. The predicted modes on the critical speeds are the combined bending modes of the intermediate and output shaft, and the lateral vibrations dominate when compared to the torsional vibrations. The damped natural frequency does not strongly depend on the rotating speeds, owing to the relatively low rotating speed of the intermediate and output shaft and constant stiffness of the roller bearing. In addition, the logarithmic decrements of all the modes are positive; therefore all modes are stable.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2004년도 전력전자학술대회 논문집(2)
• /
• pp.803-806
• /
• 2004

In this paper, configuration of prototype 300kVA UPS system with unity input power factor is briefly described and a various types of rectifier for UPS application are discussed. Input LCL filter for PWM rectifier and output LC filter for PWM inverter are designed as a prototype and their principal characteristics are discussed.

• 한국지능시스템학회:학술대회논문집
• /
• 한국퍼지및지능시스템학회 1993년도 Fifth International Fuzzy Systems Association World Congress 93
• /
• pp.985-988
• /
• 1993

An alternative approach to the design of application-driven fuzzy systems is proposed. A broad class of fuzzy systems applications requires a certain fuzzy partition of the input space while it demands for simple numerical quantities. For this class, a dedicated fuzzy system archictecture is presented and a design strategy is proposed. Both the single-input/single-output and multi-input/multi-output cases are considered. Numerical analysis are complete illustrating several aspects of the proposed framework.

• 산업경영시스템학회지
• /
• 제42권3호
• /
• pp.8-14
• /
• 2019

Most of the data envelopment analysis (DEA) models evaluate the relative efficiency of a decision making unit (DMU) based on the assumption that inputs in a specific period are consumed to produce the output in the same period of time. However, there may be some time lag between the consumption of input resources and the production of outputs. A few models to handle the concept of the time lag effect have been proposed. This paper suggests a new multi-period input DEA model considering the consistent time lag effects. Consistency of time lag effect means that the time delay for the same input factor or output factor are consistent throughout the periods. It is more realistic than the time lag effect for the same output or input factor can vary over the periods. The suggested model is an output-oriented model in order to adopt the consistent time lag effect. We analyze the results of the suggested model and the existing multi period input model with a sample data set from a long-term national research and development program in Korea. We show that the suggested model may have the better discrimination power than existing model while the ranking of DMUs is not different by two nonparametric tests.

• 한국정밀공학회지
• /
• 제28권7호
• /
• pp.814-820
• /
• 2011

It takes long time in numerical simulation because structural design for tire requires the nonlinear material property. Neural networks has been widely studied to engineering design to reduce numerical computation time. The numbers of hidden layer, hidden layer neuron and training data have been considered as the structural design variables of neural networks. In application of neural networks to optimize design, there are a few studies about arrangement method of input layer neurons. To investigate the effect of input layer neuron arrangement on neural networks, the variables of tire contour design and tension in bead area were assigned to inputs and output for neural networks respectively. Design variables arrangement in input layer were determined by main effect analysis. The number of hidden layer, the number of hidden layer neuron and the number of training data and so on have been considered as the structural design variables of neural networks. In application to optimization design problem of neural networks, there are few studies about arrangement method of input layer neurons. To investigate the effect of arrangement of input neurons on neural network learning tire contour design parameters and tension in bead area were assigned to neural input and output respectively. Design variables arrangement in input layer was determined by main effect analysis.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1991년도 하계학술대회 논문집
• /
• pp.31-33
• /
• 1991

A passive power converter operating on the principle of parametric excitation, called Parametric transformer, is analyzed. The energy transfer from the input to the output is achieved through the double frequency variation of magnetic path reluctance to the input frequency without mutual flux coupling between two windings. Thus, output becomes available which is essentially independant of waveform of excitation. The mathmatical model of the device is developed and its solution is obtained. The outstanding characteristics of the device is explained from the analysis.

• 산업경영시스템학회지
• /
• 제30권3호
• /
• pp.82-88
• /
• 2007

Service engineering is a new discipline which aims at basically understanding of service and a concrete methodology using engineering approach for service design. In this paper is introduced the serviset graph [7] which is a comprehensive concept to represent service products, processes, and operation activities. The proposed concept is a degree of commonality index in a service product in order to deal with service mass customization using the input-output analysis in economic model.

• Journal of Information Technology Applications and Management
• /
• 제13권1호
• /
• pp.67-75
• /
• 2006

In this paper, we investigate the economic repercussion effects of the domestic satellite industry. The market size of the satellite industry between 2005 and 2009 is forecasted based on the world market forecast. By using the Input-Output analysis technique, three kinds of repercussion effects (domestic production, value added, workers induced by the satellite industry) between 2005 and 2009 are calculated.

• Journal of Power Electronics
• /
• 제14권6호
• /
• pp.1217-1223
• /
• 2014

A novel half load-cycle worked dual input single output (DISO) DC/AC inverter is presented. The basic circuit consists of a dual buck regulator, which works in continuous current mode. The working principle of DISO DC/AC inverter has been used. The control method applied for half load-cycle worked DISO DC/AC inverter has been studied. The control effects of the open-loop proportional control and closed-loop proportional-integral control are compared by using PSIM software. The parameters are adopted in the realistic simulation and experiment test. Moreover, the waveforms, such as voltage of modulation reference signal and output voltage, were given. The simulation and experiment results proved that the half load-cycle worked DISO DC/AC inverter could achieve good performance, gain a line frequency of 50 Hz, and verify the correctness of theoretical analysis.

• 드라이브 ㆍ 컨트롤
• /
• 제14권1호
• /
• pp.29-34
• /
• 2017

This study analyzed a life test method for a power take-off (PTO) gearbox. An engine transfers mechanical power (rotation and torque) to a hydraulic pump through a PTO Gearbox with one input shaft and three output shafts. PTO gear box durability under high loads over long time periods was tested using dynamometers. In order to reflect the rated operating conditions, power must be distributed to each output shaft, and experiments were conducted under various conditions to verify the characteristics of the distributed power. An accelerated life test was designed using speed and torque as acceleration factors. Also, efficiency tests were conducted under various load conditions. Also, a lubrication oil composition analysis was performed to analyze gearbox wear status.