• 한국결정성장학회지
• /
• 제2권2호
• /
• pp.77-82
• /
• 1992

FZ법에 의한 결정성장에 있어서 용융대는 고액 계면의 장력에 의해 유지되고 상.하부의 고체봉 사이에 위치하고 있다. 따라서, 용융대의 표면에서는 온도와 농도 차이에 의해 표면장력의 구배가 발생하고 있는 marangoni 대류의 구동력으로 작용한다. 본 연구에서 정상상태의 결정성장시는 결정의 가장자리 영역에서의 Solute 농도는 결정내부 보다도 높아지게 되고 전위의 분포도 불규칙하여 지며, void나 기포 침투, Secondary phase의 생성 및 미소균열등의 결함 발생 확률이 계면부근에서 높아지는 결과를 알 수 있었다. 이는 고액성장 계면이 marangoni 대류에 의하여 이 영역에서 온도의 국부적인 변동에 의해 불규칙하여 지게 되기 때문이라 사료된다.

• 한국재료학회지
• /
• 제4권2호
• /
• pp.166-176
• /
• 1994

Ni기 초합금은 Co, Cr, Mo, W등의 고용 강화 원소와 AI, Ti, Nb, Ta 등의 $\gamma '$ 석출 강화 원소로 구성되어 있다. 초합금의 기계적 성질과 내산화성을 개선하기 위하여 희토류 원소를 재료 내부에 첨가하거나, 코팅 재료로써 사용하고 있다. 이들 희토류 원소는 $Al_2O_3, Cr_2O_3$등의 산화물의 종류에 따라 산화물의 성장 속도와 밀착성에 영향을 미친다. Hf함유 Ni기 초합금 AF115와 $AI_2O_3$ 함유 MA6000초합금 2종을 이온 코터를 이용, Yttrium 표면개질후, 온도 1273K-1473K에서 고온 산화 수 산호 피막의 성장 속도, 결정립, 내부 구조 및 내박리성에 미치는 Yttrium 의 영향을 조사하였다. AF115와 MA6000 초합금에 Yttrium코팅을 한 결과 내부 산화물의 성장에 현저한 변화가 있었다. Yttrium의 표면 개질에 의하여, AF115의 경우는 $AI_2O_3$ 주성분의 입계 집중과 Hf의 우선 산확 억제되고, 삼각 형태의 내부 산화물이 plate형으로 변화되었다. MA6000의 경우 $AI_2O_3$ 주성분의 산화층이$Cr_2O_3$주성분의 외부 산화층과$AI_2O_3$ 주성분의 내부층으로 변화되었다.

• Geomechanics and Engineering
• /
• 제32권3호
• /
• pp.307-319
• /
• 2023

Ground fissures have a huge effect on the integrity of surface structures. In high-intensity ground fissure regions, however, land resource would be wasted and city building and economic development would be limited if the area avoiding principle was used. In view of this challenge, to reveal the seismic response and seismic failure characteristics of ground fissure sites, a shaking table test on model soil based on a 1:15 scale experiment was carried out. In the test, the spatial distribution characteristics of acceleration response and Arias intensity were obtained for a site exposed to earthquakes with different characteristics. Furthermore, the failure characteristics and damage evolution of the model soil were analyzed. The test results indicated that, with the increase in the earthquake acceleration magnitude, the crack width of the ground fissure enlarged from 0 to 5 mm. The soil of the hanging wall was characterized by earlier cracking and a higher abundance of secondary fissures at 45°. Under strong earthquakes, the model soil, especially the soil near the ground fissure, was severely damaged and exhibited reduced stiffness. As a result, its natural frequency also decreased from 11.41 Hz to 8.05 Hz, whereas the damping ratio increased from 4.8% to 9.1%. Due to the existence of ground fissure, the acceleration was amplified to nearly 0.476 m/s², as high as 2.38 times of the input acceleration magnitude. The maximum of acceleration and Arias intensity appeared at the fissure zone, which decreased from the main fissure toward both sides, showing hanging wall effects. The seismic intensity, duration and frequency spectrum all had certain effects on the seismic response of the ground fissure site, but their influence degrees were different. The seismic response of the site induced by the seismic wave that had richer low-frequency components and longer duration was larger. The discrepancies of seismic response between the hanging wall and the footwall declined obviously when the magnitude of the earthquake acceleration increased. The research results will be propitious to enhancing the utilizing ratio of the limited landing resource, alleviation of property damages and casualties, and provide a good engineering application foreground.

• Nuclear Engineering and Technology
• /
• 제49권7호
• /
• pp.1524-1536
• /
• 2017

During the fabrication process of reactor vessel head penetration (RVHP), the grain size of the tube material can be changed by hot or cold work and the inner side of the tube can also be shrunk due to welding outside of the tube. Several nonregular time-of-flight diffraction (TOFD) signals were found because of deformed grains. In this paper, an investigation of nonregular TOFD indications acquired from RVHP tubes using experiments and computer simulation was performed in order to identify and distinguish TOFD signals by coarse grains from those by Primary Water Stress Corrosion Crack (PWSCC). For proper understanding of the nonregular TOFD indications, microstructural analysis of the RVHP tubes and prediction of signals scattered from the grains using Finite Element Method (FEM) simulation were performed. Prediction of ultrasonic signals from the various sizes of side drilled holes to find equivalent flaws, determination of the size of the nonregular TOFD indications from the coarse grains, and experimental investigation of TOFD signals from coarse grain and shrinkage geometry to identify PWSCC signals were performed. From the computer simulation and experimental investigation results, it was possible to obtain the nonregular TOFD indications from the coarse grains in the alloy 690 penetration tube of RVHP; these nonregular indications may be classified as PWSCC. By comparing the computer simulation and experimental results, we were able to confirm a clear difference between the coarse grain signal and the PWSCC signal.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1312-1316
• /
• 2007

Strip casted and rolled magnesium sheet is become exiting material for car manufacturer, due to its better formability and specific strength compare with conventional extruded sheet. TWB technology was attractive for car body designer, because it saves the weight of the car without strength loss. In this study, the laser welding performance of magnesium sheet was investigated for Mg TWB panel manufacturing. The material was strip casted and rolled magnesium alloy sheet contains 3 wt% Al and 1 wt% Zn (AZ31). Lamp pumped Nd:YAG laser of 2kW was used and its laser light was delivered by optical fiber of 0.6mm core diameter to material surface with focusing optics of 200mm focal length for TWB welding. The microstructure of weld bead was investigated to check internal defects such as inclusion, porosity and cracks. Also mechanical properties and formability were evaluated for press forming of car body. For the results, there was no crack but inclusion or porosity on weld at some conditions.The tensile strength of weld was over 95% of base metal. Inner and outer panel of engine hood were press formed and assembled at elevated temperature.

• Journal of Welding and Joining
• /
• 제8권4호
• /
• pp.27-34
• /
• 1990

Integranular corrosion behaviors of KAL (Knife Line Attack) and mechanical properties such as tensile and creep rupture were investigated for the tube material used for nearly 20 years under the condition of 463.deg. C and 28 $kg/cm^2$. Based and weld metal were austenitic stainless steel AISI 321 containing Ti, AISI 347 containing Nb, respectively. KLA is a kind of the intergranular corrosion which often occurs just near the HAZ (heat affected zone) of AISI 321 and AISI 347 stainless steel due to the grain boundary sensitization. In KLA zone, intergranular corrosion crack has propagated outwards from the inner surface and carbides of white and narrow band type assuming as (Cr, Fe) carbide were confirmed. All the delta-ferrite formed in the weld metal during weld solidification has been transformed into sigma-phase since delta-ferrte was exposed for 20 years at 463.deg. C. Elongation was very low at the range from room temperature to 600.deg. C and it was confirmed that creep-rupture properties were not consideralbly affected.

• 열처리공학회지
• /
• 제9권2호
• /
• pp.147-158
• /
• 1996

Generally, analytical consideration on the behaviour of metallic structures during quenching process, and analysis on the thermal stress and deformation after heat treatment are very important in presumption of crack and distorsion of quenched material. In this study a set of constitute equations relevant to the analysis of thermo elasto-viscoplastic materials with strain hysteresis during quenching process way presented on the basis of contimuum thermo-dynamics mechanics. The thermal stresses were numerically calculated by finite element technique of weighted residual method and the principle of virtual work. In the calculation process, the temperature depandency of physical and mechaniclal properties of the material in consideration. On the distribution of elasto-viscoplastic thermal stresses according to radial direction, axial and tangential stress are tensile stress(50MPa, 1.5GPa and 300MPa) in surface and compressive stress(-1.2GPa, -1.14GPa and -750MPa) in the inner part on the other hand, radial stress is tensile stress(900MPa) in area of analysis. According to axial direction, tangential stress gradients are average 60MPa/mm on the whole. The reversion of stress takes place at 11.5 to 16.8mm from the center in area of analysing.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2007년도 춘계학술논문 발표대회
• /
• pp.1-4
• /
• 2007

This study investigated the applicability of insulation curing method with double layer bubble sheets to the man concrete subjected to cold weather. Temperature history of the mass concrete indicated that the highest temperature of center section was exhibited at $34^{\circ}C$ while the that of surface section was $25^{\circ}C$. Difference between center and surface was shown to be less $10^{\circ}C$ when the temperature of center section was peak section, and thereby associated temperature cracking index was calculated 1.5, and occurrence probability of temperature cracking was 5%, so there was no temperature cracking caused by internal restraint. No temperature crack was observed by naked eye. It was clear that early frost demage and temperature cracking could be restrained due to reducing temperature difference between inner part and outside in the case double bubble sheets applied to insulation curing method in cold weather. The maturity of mass concrete is higher than outside about $72\sim89^{\circ}$ DD, so it was demonstrated to prevent early frost demage and ensure strength excellently. Insulation curing method with double bubble sheets was more economic than heating curing method.

• 한국결정성장학회지
• /
• 제32권3호
• /
• pp.115-120
• /
• 2022

반도체 웨이퍼용 실리콘 잉곳 제조과정에서 사용되는 석영유리 도가니 내측표면의brownish ring (BR)에 대해 연구하였다. BR의 크기는 20~30 ㎛이고 비대칭 갈색 고리형태이다. 도가니 위치에 따라 BR의 크기와 분포가 상이하며, Si 잉곳 성장시 도가니 온도가 가장 높은 round 부가 가장 크고 많았다. BR은 석영유리보다 열팽창계수가 큰 cristobalite를 함유하고 있어 표면 crack이 나타나는 것으로 판단된다. BR의 발색 현상과 p in hole은 산소 결손에 의한 것으로 생각된다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제25권3호
• /
• pp.77-84
• /
• 2021

이 연구에서는 속채움 콘크리트와 길이방향 철근으로 보강된 PHC 파일에 대한 휨실험을 수행하였으며, 실험의 주요 변수는 길이 방향 철근비와 PHC 파일 중공 내부 표면에 형성된 슬러지 유무로 설정하였다. 총 6개의 PHC 파일 실험체를 제작하였으며, 실험체들의 파괴모드, 균열패턴, 단면내 길이방향 변형률 분포, PHC 파일과 속채움 콘크리트 사이에 발생된 단부 슬립을 상세히 계측하고 분석하였다. 실험결과, 길이방향 철근비가 증가할수록 휨 강성 및 강도가 증가하는 것으로 나타났으며, PHC 파일 내부 표면에 형성된 슬러지는 실험체의 휨성능에 큰 영향을 미치지 않는 것으로 나타났다. 실험적 연구와 더불어 이 연구에서는 변형률 적합조건, PHC 파일과 속채움 콘크리트 단면내 변형률 및 응력 분포를 고려한 비선형 휨해석 모델을 제안하였으며, 해석결과를 실험결과와 비교하여 제안모델의 합리성을 검증하였다. 그 결과, 제안모델은 속채움 콘크리트와 길이방향 철근으로 보강된 PHC 파일의 휨거동을 매우 우수한 정확도로 평가하는 것으로 나타났다.