• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.05a
• /
• pp.222-228
• /
• 1999

The two-microphone sound-intensity technique has been used for the detection of defects in radially loaded ball bearings. The difference in the sound-intensity levels measured for bearings with no defect and for those with intentionally introduced defects of different sizes in their elements under various operating conditions of loads and speeds is demonstrated. A change in the intensity frequency spectrum because of the defects is observed. The results show that the detectability of an outer-race defect is much better than that of on inner-race or ball defect. It is difficult to detect defects at lower speeds. Sound-pressure measurements were also performed fur comparison, and it is shown that the detectability of defects by sound-intensity measurements is better than that by sound-pressure measurements.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.31 no.5
• /
• pp.440-453
• /
• 2005

Objectives : To develop a bioactive membrane for guided bone regeneration (GBR), the biocompatibility and bone regenerating capacity of the cellulose membrane obtained from the Ascidians squirt skin were evaluated. Materials and methods : After processing the pure cellulose membrane from the squirt skin, the morphological study, amino acid analysis and the immunoreactivity of the cellulose membrane were tested. Total eighteen male Spraque-Dawley rats (12 weeks, weighing 250 to 300g) were divided into two control (n=8) and another two experimental groups (n=10). In the first experimental group (n=5), the cellulose membrane was applicated to the 8.0 mm sized calvarial bone defect and the same sized defect was left without cellulose membrane in the first control group (n=4). In the another experimental group (n=5), the cellulose membrane was applicated to the same sized calvarial bone defect after femoral bone graft and the same sized defect with bone graft was left without cellulose membrane in the another control group (n=4). Each group was sacrificed after 6 weeks, the histological study with H&E and Masson trichrome stain was done, and immunohistochemical stainings of angiogenin and VEGF were also carried out. Results : The squirt skin cellulose showed the bio-inductive effect on the bone and mesenchymal tissues in the periosteum of rat calvarial bone. This phenomenon was found only in the inner surface of the cellulose membrane after 6 weeks contrast to the outer surface. Bone defect covered with the bioactive cellulose membrane showed significantly greater bone formation compared with control groups. Mesenchymal cells beneath the inner surface of the bioactive cellulose membrane were positive to the angiogenin and VEGF antibodies. Conclusion : We suppose that there still remains extremely little amount of peptide fragment derived from the basement membrane matrix proteins of squirt skin, which is a kind of anchoring protein composed of glycocalyx. This composition could prevent the adverse immunological hypersensitivity and also induce bioactive properties of cellulose membrane. These properties induced the effective angiogenesis with rapid osteogenesis beneath the inner surface of cellulose membrane, and so the possibilities of clinical application in dental field as a GBR material will be able to be suggested.

• Journal of Korea Multimedia Society
• /
• v.21 no.6
• /
• pp.649-658
• /
• 2018

In this paper, we propose a mechanical contact inner tap inspection system that can inspect the defect of the inner tap immediately after inner tap is processed within the machining center. The inspection module has the collet chuck structure, so it can mounted on the main spindle of the machining center during inspection. It was developed with a focus on inspection for tap having 20 mm depth which is primarily fabricated in automotive parts and has a double sided PCB-type control system including sensing function based on Zigbee module, micom and IR sensor for wireless transmission of measured data with low power operation, and also a battery for supplying electric power. The current consumption is 46.8mA in the inspection operation mode and 0.0268mA in the power saving mode for 3.7V of the applied power source, so that 30,000 times or more inspection can be performed with assumed 5 seconds inspection time for one tap. Experiments in test jig system and actual machining center confirm that the proposed inner tap inspection system can be applied to the batch process of simultaneous inspection after tapping in the machining center.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.18 no.4
• /
• pp.746-757
• /
• 1996

Bony defects may be found as a result of congenital anomalies, traumatic injury, automobile collisions and industrial accidents in the maxillofacial area. Such conditions are often associated with severs functional and esthetic problem. Various surgical procedure has been utilized in attempts to repair and reconstruct bony defects. Bone is a complex, living, constantly changing tissue. The architecture and composition of cancellous and cortical bone allow the skeleton to perform its essential mechanical functions. Periosteum covers the external surface of bone and consists of two layers : an outer fibrous layer and an inner more cellular and vascular layer. The inner osteogenic layer or cambium layer can form new bone while the outer layer firms part of the insertions of tendons, ligaments and muscles. This study was under taken to evaluate bone healing process on partial defect of calvarial bone with or without periosteum in rat. We made calvarial defects of different size(4mm, 6mm, 8mm) with periosteum or without periosteum in rat to study the effect of defect size on healing process. Control and experimental groups sacrified at 1, 2, 4, 6, 8 weeks, postoperatively. We examed the specimens by gloss findings, light microscophy, and fluorescent microscophy. The results were as follows. 1. Gloss findings: Control groups are larger bony defects than experimental groups after 2 weeks, and than control groups advanced healing of defected bone but experimental groups are lesser after 4, 6 weeks. After 8 weeks, bone defect has not been identified in control and experimental groups. 2. Light microscope: All defects of control groups are larger bony defects than experimental groups after 2 weeks. And than control groups show smaller defect after 4 weeks. After 8 weeks, the control group reveal pin-point sized, hardly identifiable defect space and the experimental group reveal small, but definite defect space. 3. Fluorescent microscope : Each week, new bone formation of control group is very similar to the experimental group. In this study, Osteogenesis of calvarial bone defects with periosteum or without periosteum was examined for 8 weeks in rats. The replaced periosteum had batter new bone formation than the removed periosteum.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.9
• /
• pp.37-44
• /
• 2001

Ultrasonic testing has a characteristics such as excellent permeability, high-sensitivity to find defect and an almost exact measurement for position. size and direction of inner defect, which differ from other non-destructive testing. In the study, we developed program into optimal testing condition, to distinguish obstacle echo and defect position. This program shows generation and processing of ultrasonic pulse. We compared simulation with ultrasonic test in 45$^\circ$, 60$^\circ$and 70$^\circ$transducer. Test results were in accordance with simulation within 0.1~7.2%.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.4
• /
• pp.473-479
• /
• 1999

The two-microphone sound-intensity technique has been used for the detection of defects in ra-ally loaded ball bearings. The difference in the sound-intensity levels measured for bearings with no defect and for those with intentionally introduced defects of different sizes n heir elements under various operating conditions of loads and speeds is demonstrated. The results show that of an inner-race or ball defect. It is difficult to detect defects at lower speeds. Sound-pressure measurements were also performed for comparison and it shown that the detectability of defects by sound-intensity measurements is better than that by sound-pressure measurements.

• Design & Manufacturing
• /
• v.14 no.4
• /
• pp.52-57
• /
• 2020

In this study attempted to prevent defects due to blow holes among defects of sand casting products. It was intended to reduce the defect rate by reducing the blow hole of the inner surface. Currently, expectations and requirements for the quality level of non-ferrous aluminum casting in the casting industry are increasing. In addition, the shape is complex and the shrinkage precision is required. Among them, the test prototype is expensive to manufacture the mold, and the production time is also long, and the product is manufactured by sand casting. At this time, the highest defect rates are defects caused by shrinkage defects, surface defects, and blow holes.. At this study, the manufacturing time was shortened by using the shape of the fluid movement path in advance. Also, it is possible to reduce defects due to blow holes.

• Design & Manufacturing
• /
• v.6 no.2
• /
• pp.79-83
• /
• 2012

Inner part is used as an insulator in wire fuses. After injection molding, inner part has been showed flashes, filling defects and deformation. After production, operators have to cut off flashes, one by one. this process leads to continuous low productivity and loss of source materials. This study focuses on identifying the causes for flashes, filling defects, clamping force of injectors, mold adhesion, resin of liquidity and others, and on resolving those issues.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.11
• /
• pp.876-881
• /
• 2011

The sintering, defect and grain boundary characteristics of Bi-based ZnO chip varistor (1,608 mm size) have been investigated to know the possibility of lowering a manufacturing price by using 100 % Ag inner-electrode. The samples were prepared by general multilayer chip varistor process and characterized by shrinkage, SEM, current-voltage (I-V), admittance spectroscopy (AS), impedance and modulus spectroscopy (IS & MS) measurement. There are no problems to make a chip varistor with 100% Ag inner-electrode in the sintering temperature range of 850~900$^{\circ}C$ for 1 h in air. A good varistor characteristics ($V_n$= 9.3~15.4 V, a= 23~24, $I_L$= 1.0~1.6 ${\mu}A$) were revealed but formed $Zn_i^{{\cdot}{\cdot}}$(0.209 eV) as dominant defect, and increased the distributional inhomogeneity and the temperature instability in grain boundary barriers.

• Journal of Power System Engineering
• /
• v.7 no.2
• /
• pp.66-72
• /
• 2003

Recently, the steel parts used at the aerospace and automobile industries are required to be used light weight parts. Therefore, used material, steel have to be a high stress, which is an indispensable condition in this field. At the consideration of parts design, high hardness of the lightweight parts have an benefit of saving fuel and material. A high stress of metal has a point of difference according to the shape of design, external cyclic load and condition of vibration. A crack generates on the surface of metal or under yield stress by defect of inner metal defect or surface defect and slowly, this crack grow stable growth. Finally, rapidity failure phenomena is happen. Fatigue failure_phenomena, which happen in metal, bring on danger in human life and property therefor, anti-fatigue failure technology take an important part of current industries Currently, the shot peening is used for removing the defect from the surface of steel and improving the fatigue strength on surface. Therefore, this paper investigated the effect on frcature toughness using shot peening which is improve the resistance of crack growth and crack expansion rate by fatigue that make a compressive residual stress on surface.