• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.5
• /
• pp.75-81
• /
• 2001

This paper presents the atomization characteristics of single hole injector in the direct injection type diesel engine. The spray characteristics of fuel injector such as the droplet size and velocity were measured by phase Doppler particle analyzer. In this paper, the atomization characteristics of fuel spray are investigated for the experimental analysis of the measuring data by the results of mean diameter and mean velocity of droplet. The effect of fuel injection pressure on the droplet size shows that the higher injection pressure results in the decrease of mean droplet diameter in the fuel spray. The minimum size of fuel spray droplet appears on the location of 40mm axial distance from nozzle exit of diesel injector. Based on the experimental results, the correlation between the droplet diameter and mean velocity of the diesel spray due to the change of axial and radial distance from the nozzle tip were investigated.

• Journal of ILASS-Korea
• /
• v.11 no.4
• /
• pp.205-211
• /
• 2006

Impinging angle, impinging distance, length eve. diameter and injection pressure of a triplet injector were tested to evaluate the spray characteristics injected by liquid/gas combinations. Two different kinds of unlike triplet sprays were produced by changing the gas and liquid feed lines. One was the G-L-G(Gas-Liquid-Gas) type, and the other was L-G-L(Liquid-Gas-Liquid) type. Spray angles were wider with the G-L-G type than with L-G-L type. Mass distributions in spray were obtained with a, mechanical patternator. Mass distributions were not circular but elliptical distributions. When the range of mechanical patternator to injector decreased, mass distributions were more concentrated in the center region.

• Journal of ILASS-Korea
• /
• v.8 no.3
• /
• pp.19-26
• /
• 2003

In this study, experimental study on atomization characteristics of the fuel spray impinging on the wall was at different wall distances and angles of wall inclination. The fuel injection system was composed based on the common rail system. and the injection signal was synchronized by the delay generator. The atomization characteristics of the injected spray were analyzed in terms of the SMD and velocities which were measured by using the phase Doppler particle analyzer system. It is revealed that the free spray is atomized actively above 50mm form the injector tip. In the cases of the impinged spray, the 5MD and velocity of the impinged spray are smaller than those of the free spray. The impinged spray has the maximum near the 35mm of the radial distance from the injector axis, and the atomization performance is enhanced with the decrease of the wall distance.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.8
• /
• pp.45-51
• /
• 2007

We designed and fabricated the planar graded-gap injector GaAs Gm diodes with $1.6{\mu}m$ active length for operation at 94 GHz. The fabrication of the Gunn diode is based on MESA etching, Ohmic metalization, and overlay metalization. The measured negative resistance characteristics of the graded-gap injector GaAs Gunn diodes are examined for two different device structures changing the distance between the cathode and the anode electrodes. Also, we discuss the DC results under the forward and the reverse biases concerning the role of the graded-gap injector. It is shown that the structure having the shorter distance between the cathode and the anode electrode has higher peak current, higher breakdown voltage, and lower threshold voltage than those of the larger distance.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.236-239
• /
• 2017

A part of the development of Scramjet Engine, this study was performed about Injectors. Barbotage injectors were used for experiment. To study characteristics of injector spray, water is supplied as a main fuel and Nitrogen is supplied for water atomization. Spray test facility and PDPA equipment were used in KARI(Korea Aerospace Research Institute). It was found that gas pressure change and spray distance is important value to spray atomization.

• Journal of ILASS-Korea
• /
• v.20 no.2
• /
• pp.114-120
• /
• 2015

Effects of injection conditions on a pintle injector which is proper to recent liquid rocket engines requiring low cost, low weight, high efficiency and reusability were studied. The pintle injector with a typical moving pintle was used for atmospheric experiment using water and air. Injection pressures of water were considered 0.5 and 1.0 bar, 0.1 to 1.0 bar for injection pressures of air and 0.2 to 1.0 mm for pintle opening distance. Sauter mean diameters (SMD) of spray was measured at 50 mm distance from a pintle tip and SMD was treated as a representative parameter in this study. As a result, because of shape characteristics of the pintle injector, there was a transient region between the pintle opening distances of 0.6 and 0.7 mm and this region affected to mass flow rates and SMDs. Also, Reynolds numbers for gas, Weber numbers and momentum ratios were adopted as major non-dimensional paramters and the momentum ratio has strong correlation with SMD.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.1
• /
• pp.62-68
• /
• 2005

An injector for fuel rich gas generator was designed and experimentally investigated. Five variations of F-O-F triplet impinging type injector were tested to evaluate spray characteristics with kerosene/water simulant propellant. Test was focused to find the effect of design variables of impinging angle, and impinging distance, on the atomization performance. A mixing efficiency is used to compare droplet distribution and local O/F ratio of each injector in the range of momentum ratio of 0.2~1.3. Test results shows the max value of mixing efficiency locates about the 0.8 in momentum ratio. And the injector with an impinging angle of 45 degree and impinging distance of 6mm shows the very good performance result suitable for fuel rich gas generator. A combustion test will be also conducted with selected injector to verify the spray pattern and mixing efficiency.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.3
• /
• pp.14-25
• /
• 2021

An experimental study was conducted on the spray characteristics of the pintle injector by opening distance. The discharge coefficient of the pintle injector was investigated and the spray angle was measured by taking the spray image by test conditions. As a result of the measurement of the discharge coefficient, it was confirmed that the change in the discharge coefficient of the outer injector was not significant over the experimental conditions, but the change in the discharge coefficient of the inner injector was decreased as the flow rate increased. Measurement of the spray angle showed that the change in the spray angle was not significant in the conditions under which the spray was fully developed, but the spray was not fully developed at low flow rates. This confirmed the possibility of thrust control using the pintle injector.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.3
• /
• pp.1005-1014
• /
• 1996

An experimental investigation has been carried out to examine the influence of injector design variables and operating conditions on the resultant drop size for triplet impinging streams injectors. The variables studied in this investigation are pressure drop, impinging angle, orifice length to diameter ratio, and impinging point distance. Droplet-size data are obtained using water as the propellant simulant by Malvern Particle Analyzer System. Drop size decreases with increasing impinging angle and pressure drop while other injector parameters remain constant at the same point. But it is found that there is no noticeable droplet-size change which results from change in orifice length to diameter ratio or impinging point distance within the investigated range.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.3
• /
• pp.165-172
• /
• 2022

Pintle injector is the most suitable injector for thrust control because it can control the area of propellant injection. Accordingly, the combustion test of multiple hole pintle injector and continuous type pintle injector was carried out in this paper using liquid oxygen and gas methane. The combustion performance of the two pintles was verified with the characteristic speed efficiency, and the experimental results were compared according to the O/F and combustion chamber pressure and under similar conditions. The efficiency of the multi hole pintle was generally somewhat higher than continuous pintle when pintle opening distance(the area of dispensing oxidizer) was in a 100% thrust condition.