• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.122-122
• /
• 2013

In this talk, some optical properties of quantum dot based mode-locked diode lasers and photonic crystal nano lasers will be discussed. Linewidth enhancement factor, chirp and interband injection locking technique of quantum dot mode-locked lasers will be presented. Also various types of photonic crystal buried heterostructure lasers toward coherent nano laser will be covered as well.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 2004.11a
• /
• pp.412-412
• /
• 2004

• 한국금형공학회:학술대회논문집
• /
• 2008.06a
• /
• pp.159-162
• /
• 2008

High pressure is involved during injection molding operation specially packing phase. Cracks in the mold are often occurred by high cavity pressure. In this study, structural analysis of mold has been performed using commercial softwares, Abaqus and Ansys, to investigate cause of crack in the injection mold. Structural analysis contains four cases: stress distribution according to the cavity pressure, stress concentration according to the boundary conditions, stress concentration for inter-locking design of mold, and stress concentration for distributed cavity pressure. Through this study it was observed that the locations of stress concentrations were coincident with locations of crack. Robust mold design is being required to withstand high cavity pressure.

• Journal of the Optical Society of Korea
• /
• v.20 no.6
• /
• pp.698-703
• /
• 2016

We report a new all-optical flip-flop (AOFF) with a quite simple structure, using optical beating in an injection-locked Fabry-Perot laser diode (FP-LD) with optical bistability. While conventional AOFF methods using an injection-locked FP-LD require additional devices such as secondary FP-LDs or polarization controllers for reset operation, the proposed method can be implemented using only a single commercially available FP-LD with set and reset signals. The optical beating induces intensity fluctuations inside the FP-LD, and releases the locking state to the reset state. Even though we demonstrated the AOFF at 100 Mbit/s, we expect that its operation rate could extend to 10 Gbit/s, according to the limit of the FP-LD's frequency response.

• Korean Journal of Optics and Photonics
• /
• v.1 no.2
• /
• pp.191-197
• /
• 1990

An experiment on the phase stability of injection-locked beam is done by using AlGaAs semiconductor lasers. The coherence of two beams from the master and slave lasers is measured by interference between the beams in the Twymann-Green interferometer. The phase change of the output beam of the slave laser as a function of the driving current is measured in the Mach-Zehnder interferometer consisted of the master and slave lasers and a value of 2.5radlmA is obtainccl.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.297-300
• /
• 2008

High pressure is involved during injection molding operation specially packing phase. Cracks in the mold are often occurred by high cavity pressure. In this study, structural analysis of mold has been performed using commercial softwares, Abaqus and Ansys, to investigate cause of crack in the injection mold. Structural analysis contains four cases: stress distribution according to the cavity pressure, stress concentration according to the boundary conditions, stress concentration for inter-locking design of mold, and stress concentration for distributed cavity pressure. Through this study it was observed that the locations of stress concentrations were coincident with locations of crack. Robust mold design is being required to withstand high cavity pressure.

• Korean Journal of Optics and Photonics
• /
• v.5 no.2
• /
• pp.278-285
• /
• 1994

We investigated the spectral characteristics for temperature and driving current change in visible laser diode. As a result of spectrum analysis, the ratio of frequency change for temperature and driving current change were about $33 GHz/^{\circ}C$, 6.6 GHz/mA in the region which was not mode hopping range. Compared to the sharp mode hopping in the near IR single mode AlGaAs lasers, the visible laser diode showed relatively broad multimode operation in the mode hopping region. We performed the experiment of injection-locking characteristics analysis for visible laser diode. Locking half bandwidth(LHBW) was measured 0~5.0 GHz for $0~25\muW$ input power and it was dependent on the input power. Also, LHBW for polarization angle was dependent on the difference of polarization angle between master laser and slave laser. The phase change of injection-locked output beam of the slave laser diode as a function of the drive current was measured in the interferometer which was composed of master laser and slave laser. The ratio of phase change with the slope of 5.0~1.3 rad/mA was obtained within injection-locking range for the change of $2~25\muW$ input power. power.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.3
• /
• pp.292-298
• /
• 2011

In this paper, a voltage controlled injection-locked oscillator(VC-ILO) is proposed for wideband applications. From the control of the free-running frequency by a varactor diode, the wide frequency locking range can be obtained for low-level injected signals. The proposed VC-ILO is implemented on an FR-4 substrate with a thickness of 0.8 mm. The free-running frequencies of the oscillator is 2.39~2.52 GHz at the control voltage of 0~5 V. While the frequency locking range of over 50 MHz is presented for -10 dBm injected signal level at a fixed frequency, the locking range of over 90 MHz can be achieved for -30 dBm by controlling the free-running frequency.

• Journal of Advanced Navigation Technology
• /
• v.3 no.1
• /
• pp.1-12
• /
• 1999

For the phase measurement of radar signal in the coherent-on-receiver system, the COHO(Coherent Oscillator) generates the signal which locks to the phase of the transmit pulse. In this paper, COHO unit is developed to generate 60 MHz phase-locked signal. ILO(Injection Locking Oscilator) locks to the sample of the transmit pulse. Gate circuit, ILO, buffer amplifier, and pulse generator are designed and implemented.

• Journal of the Optical Society of Korea
• /
• v.12 no.4
• /
• pp.326-336
• /
• 2008

A WDM-PON has been considered as an ultimate solution for access networks. However, there were many technical and practical issues for commercial deployment. These issues were solved with wavelength locked F-P LD and the WDM-PONs employing this optical source were commercialized. These WDM-PON systems have been deployed in Korea, Europe, and US. We reviewed wavelength locking technology and WDM-PON achievements. When we inject spectrum sliced broadband light into an F-P LD, the multimode output is changed to a quasi single mode. Then, we can use the single mode light for WDM signal transmission. The broad spectral gain of the semiconductor gain medium enables a color-free operation of WDM-PON, i.e., an identical ONT can be used for each user. The wavelength locking properties depend on many parameters, especially alignment of injection wavelength to a lasing mode, passband profile of AWG and front facet reflectivity of F-P LD. However, these dependencies can be reduced by proper design of the laser and the injection bandwidth. Thus, WDM-PON systems have been achieved with color-free operation.