• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.6
• /
• pp.37-43
• /
• 2003

The objective of this work is to investigate the effect of swirl, injection pressure and pilot injection on D.I. diesel combustion by using a transparent engine system. The test engine is equipped with common rail injection system to obtain high pressure and to control injection timing and duration. In this study, the combustion analysis and steady flow test were conducted to estimate the heat release rate from in-cylinder pressure. Soot distribution in diffusion flame according to swirl ratio, injection pressure and pilot injection was investigated by using LII technique. As the results, high injection pressure was found to shorten ignition delay as well as enhance peak pressure and heat release rate was greatly affected by injection timing and pilot injection. In addition, the results showed that the period of soot formation corresponded to the diffusion flame.

• Journal of Power System Engineering
• /
• v.9 no.4
• /
• pp.83-89
• /
• 2005

Molding shrinkage is one of the problems to be solved in conventional injection molding. Despite many trying-out has been to solve it, intrinsic cause of shrinkage such as orientation and thermal exchange between melt and mold has not been solved yet. For reducing shrinkage and residual stress on molding, injection compression molding process was invented. In this study, experiments about effects of injection compression molding's parameters on shrinkage of PMMA molding were conducted and compared with conventional injection molding's shrinkage. Before the injection compression molding experiment, molding shrinkage rate was predicted by analyzing pvT diagram and was compared with the results of experiment. The shrinkage rate of injection compression molding was lower than convention injection molding's one which was different from the predicted shrinkage. The reason was observed that the experimental mold was not a proper type for injection compression, flowing backward of melt into nozzle and unreasonable mechanism of injection molding machine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.6
• /
• pp.30-37
• /
• 2007

The injection and spray characteristics of top-feed type injector was investigated under liquid phase injection fueled with liquefied petroleum gas (LPG). Different pressures and temperatures of fuel injection system were tested to identify the injection characteristics after hot soaking. MIE-scattering technique was used for verification of successful liquid phase injection after hot soaking. In case of bottom-feed type injector, the injection was accomplished at every experimental condition. In case of top-feed type injector, when the pressure of LPG was over 1.2 MPa, the injection was not executed. However, under the pressure were 1.2 MPa, the liquid phase injection after hot soaking was accomplished. The engine with top-feed type fuel injection equipment was restarted successfully after hot soaking.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.10 no.6
• /
• pp.191-197
• /
• 2006

This study is to establish a standardization of injection system by inorganic material for crack repair of tunnel concrete structures. For this various surveys and experiments were carried out as followed. The first we surveyed capability of injection and crack pattern of concrete structures in site. and second we analyzed the relationship between crack width and volume of injection, and decided pressure and volume of injection. Finally we evaluated the relationship between crack width and volume of injection with kind of concrete structures, and between required time for injection and crack width with thickness of structure. From these surveys and experiments, we cleared the relationship between crack patterns and injection technologies such as volume, pressure of injection and required time for injection with kind of structure.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.10a
• /
• pp.337-340
• /
• 2022

SQL Injection attacks are one of the older attack techniques and are the dominant type of hacking attempts against web services. There have been many attempts to hack SQL injection attacks by exposing data or obtaining privileges. In this paper, we implement a log analysis system that can respond to SQL injection attacks in real time using the open source ELK Stack. did. By providing a visualization of SQL injection attack log data through the implemented system, it is expected that users will be able to easily grasp the degree of attack risk and quickly prepare for attacks.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.9
• /
• pp.192-203
• /
• 2001

The design of gate and runner(delivery system) is one of the most important subject in injection molding. Delivery system is a channel to flow the polymer melt from the injection molding machine to the mold cavities. Also, delivery system affect quality and productivity of the part. The synthesis of delivery system of injection molding has been done empirically, since it requires profound knowledge about the moldability and causal effects on the properties of the part, which are not available to designers through the current CAD systems. GATEWAY is a knowledge module which contains knowledge to permit non-experts as well as mold design experts to generate the acceptable geometries of gate and runner far injection molded parts. A knowledge-based CAD system is constructed by adding the knowledge module, GATEWAY, to an existing geometric modeler. A knowledge-based CAD system is a new tool which enables the concurrent design and CIM with integrated and balanced design decisions at the initial design of injection molding.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.3
• /
• pp.338-344
• /
• 2016

The study is actively being performed to increase fuel injection pressure of common rail system among countermeasures to meet the emission regulation strengthen of the Diesel engine. The common rail fuel injection tube in such ultra high pressure common rail system has the weakest structural characteristics against vibration that is generated by fuel injection pressure and pulsation during engine operation and driving. Thus the extreme durability is required for common rail fuel injection tube, and the drawing process is being magnified as the most important technical fact for strength of seamless pipe that is the raw material of common rail tube. In this respect, we analyzed the characteristic of dimension and stress variation of the ultra high pressure common rail fuel injection tube by variation of Die and Plug angle in drawing process. Based on the analysis, we tried to obtain the raw material strength of common rail fuel injection tube for applying to the ultra high pressure common rail system. As a result, Plug angle is more important than entry angle of Die and we could obtain the target dimension and strength of the ultra high pressure common rail fuel injection tube through optimization of Plug angle.

• Journal of ILASS-Korea
• /
• v.9 no.1
• /
• pp.8-14
• /
• 2004

future exhaust emission limits for diesel-driven passenger cars will force the automotive company to significantly develop of the new technologies of diesel engine respectively of the drive assemblies. As we know, the contributions of soot and nitrogen oxide is the main problems in diesel engine. Recently, as a result, the pilot injection of common-rail fuel injection system recognizes an alternative function to solve an environmental problem. This study describes the effect of the nozzle structure and driven characteristic of injector on pilot injection fur a passenger car common-rail system. The pilot spray structure such as spray tip penetration, spray speed and spray angle were obtained by high speed images, which is measured by the Mie scattering method with optical system fur high-speed temporal photography. Also the CFD analysis was carried out for fuel behavior under high pressure in between needle and nozzle of injector for common-rail system to know the condition of initial injection at experiment test. It was found that solenoid-driven injector with 5-hole was faster than 6-hole injector in spray speed at same conditions and piezo-driven injector showed faster response than solenoid injector.

• Journal of The Korean Dental Society of Anesthesiology
• /
• v.6 no.2 s.11
• /
• pp.98-102
• /
• 2006

The purpose of this study was to evaluate the difference on pain intensity and discomfort between pressure-controlled injection system and conventional syringe injection technique from the patients undergoing oral and maxillofacial surgery. In a prospective, randomized, case-controlled study, 60 patients were divided into two groups (n=30 in each). In experimental group, pressure-controlled injection system was applied. In control group, conventional syringe injection system was applied. Pain rating score (PRS) and visual analogue scale (VAS) were assessed. The average of VAS in experimental group ($16.67{\pm}15.07$) was smaller than that of control group ($25.63{\pm}22.21$), though there were no significant differences (P=0.072). In PRS, fifteen patients (50.0%) of experimental group answered that they experienced mild pain. However sixteen patients (53.3%) of control group answered that they experienced intermediate pain. From the results, pressure-controlled injection system may be an effective method to reduce pain during the dental local anesthetic procedure.

• Journal of Power System Engineering
• /
• v.13 no.4
• /
• pp.38-42
• /
• 2009

The Injection molding is used more than 70% of total production in plastic products. The injection molding process has 4 processes such as filling, packing, cooling and ejecting. now then, cooling process spends the most of times in Injection molding cycle time. Therefore, it is important to control the mold temperature in producing plastic products. The cooling system and time affect the product's quality and productivity. Especially, cooling time has about 60% of total injection cycle time. Therefore, we can improve a productivity by shortening cooling time. In this study, the rapid cooling system was developed and performed a efficiency test. This system could refrigerate coolant to $1^{\circ}C$ and had to need 10 minutes for normal operating.