• 전산구조공학
• /
• 제10권1호
• /
• pp.173-183
• /
• 1997

본 논문에서는 랜덤한 축대칭 기하학적 초기결함을 갖는 원통이 축방향 충격하중을 받는 경우의 반경방향 변위가 임계기준치를 최초로 통과하는 확률론적 충격좌굴 파괴시간을 해석할 수 있는 방법을 제시하였다. 랜덤한 기하학적 초기결함의 생성을 위해 초기결함의 평균함수 및 상관함수를 이용하여 확률장을 형성하는 방법을 사용하였다. 본 논문에서 제시된 방법은 실제적인 기하학적 초기결함이 갖는 불확실성을 취급하는데 적절하고 실용적이므로 이를 고려한 원통의 구조안전도해석에 이용할 수 있다.

• 한국산업융합학회 논문집
• /
• 제22권6호
• /
• pp.649-655
• /
• 2019

Fracture behaviors of SCM435 high strength bolt have been studied including macroscopic and microscopic fracture observation, Energy Dispersive X-ray Spectroscopy, Vickers hardness test and applied stress evaluation. cracks (ratchet marks) were generated by the repetitive loads acting on the bolts, initial stress of bolt and the stress concentration. The applied stress was found to be slightly higher than the fatigue limit of the material. The initial stress of bolt must be removed, and the mold temperature during the process must be maintained by room temperature. Bolts are recommended to be peened to improve fatigue limit.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제11권1호
• /
• pp.11-21
• /
• 2019

In product design, the initial design stage is being increasingly emphasized because it significantly influences the successive product development and production stages. However, for larger and more complex products, it is very difficult to accurately predict product reliability in the initial design stage. Various design methodologies have been proposed to resolve this issue, but maintaining reliability while exploring design alternatives is yet to be achieved. Therefore, this paper proposes a methodology for conceptual design considering reliability issues that may arise in the successive detailed design stages. The methodology integrates the independency of axiomatic design and the hierarchical structure of failure mode, effects, and criticality analysis (FMECA), which is a technique widely used to analyze product reliability. We applied the proposed methodology to a liquefied natural gas fuel gas supply system to verify its effectiveness in the reliability improvement of the design process.

• 한국철도학회논문집
• /
• 제11권3호
• /
• pp.280-285
• /
• 2008

Gurson model과 shear failure model 두 가지 파괴모델을 이용하여 노치인장시험과 초기 균열을 가지는 파쇄튜브의 압축거동을 유한요소법으로 해석하였다. Shear failure model의 파라미터 값은 노치인장시편의 시험 및 해석을 통하여 결정하였다. 항복강도와 파괴전단변형률 등의 파라미터 값을 정한 후, Gurson model과 shear failure model을 파쇄튜브의 해석에 적용하였다. Gurson model과 shear failure model이 인장시편에 대하여는 비슷한 파괴 거동을 보여주지만 파쇄튜브의 압축력과 균열 성장 속도에서는 다른 결과를 보임을 확인하였다. 즉, shear failure model에서는 Gurson model에 비하여 균열이 전파되기 위해 더 큰 압축력이 요구되었다. 이러한 현상은 shear failure model 이 재질의 손상 과정에 대한 고려를 포함하고 있지 않기 때문인 것으로 생각된다. 어느 모델이 튜브의 해석에 적당한 지를 실험을 통하여 검증할 필요가 있다.

• 한국강구조학회 논문집
• /
• 제10권4호통권37호
• /
• pp.749-758
• /
• 1998

현장타설 콘크리트 바닥판 교량의 전단연결부의 강성 평가를 분석하고 프리캐스트 콘크리트 바닥판 교량의 전단연결부의 강성을 평가하기 위한 실험을 통해 전단강성을 구하였다. 전단연결부 채움재료의 강도특성에 대한 변수연구와 국부적인 응력분포를 파악하기 위하여 push-out 실험부재에 대한 3차원 유한요소해석을 수행하였다. 해석을 통해 구한 하중-슬립관계를 실험에서 구한 것과 비교하여 타당성을 검증하고 프리캐스트 바닥판 교량 전단연결부의 초기 강성에 대한 평가식을 제안하였다. 선형해석을 수행하여 전단연결재 지름과 모르터의 강도에 따른 손상의 양상과 전단연결재와 무수축모르터에 각각 파괴기준을 적용하여 파괴하중을 예측하고 실험값과 비교하였다.

• 대한토목학회논문집
• /
• 제33권4호
• /
• pp.1489-1498
• /
• 2013

본 연구에서는 불포화 사면에서 선행강우의 영향을 고려하고자 지반의 초기 포화도를 3가지(36, 51, 77%)로 설정하여 수리학적-역학적 동시 유한요소해석(monolithically coupled finite element analysis)을 수행하였다. 선행강우에 의한 불포화 사면의 불안정성은 사면 내 모관흡수력 분포와 사면표층의 변위를 통하여 확인할 수 있다. 또한 Drucker-Prager model의 항복경계기준(trial failure criterion)을 적용하여 강우 침투에 의한 불포화 사면의 탄성 및 소성거동을 파악하였다. 그 결과, 선행강우에 의한 지반의 초기 포화도가 클수록 강우에 의한 변위가 크게 발생하며 모관흡수력 또한 감소한다. 특히, 모관흡수력은 지반이 건조할수록 빠르게 감소하며, 초기에 동일한 모관흡수력을 갖는 사면표층에서 포화도가 작은 지반일수록 더 빠른 모관흡수력 감소를 보였다. 풍화토의 탄성과 소성거동을 구분하기 위해 사용된 Drucker-Prager model을 통해 사면 파괴가 시작되는 항복경계지점을 확인 할 수 있었다.

• 한국기계가공학회지
• /
• 제19권2호
• /
• pp.81-88
• /
• 2020

The damping hinge of a built-in refrigerator was examined in terms of its stress and fatigue life. Analysis of the initial design showed that stress concentration occurred at the concave surface of the hinge lever, which was broken during the door opening-and-closing endurance test of the prototype. The maximum von Mises stress at this location exceeded the yield strength. In addition, Goodman fatigue analysis of the initial design showed that the fatigue life at this location was consistent with the failure observed during the endurance test. Based on these results, an improved design for the damping hinge was derived. Analysis of this improved design showed that the stress concentration in the hinge lever of the initial design was eliminated. In this case, the maximum stress occurred at the position where the hinge lever was in contact with the door stopping pin, and the maximum von Mises stress was smaller than the yield strength. Goodman fatigue analysis of the improved design indicated that the fatigue life of the entire damping hinge was infinite. It was therefore concluded that the improved design does not suffer from fatigue damage during the endurance test.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1216-1221
• /
• 2003

The specimen materials used in this research is bimaterial. The static photoelastic experiment was applied to them. And then the specimens used in photoelastic experiment were fractured under static load. The static photoelastic hybrid method was introduced and it's validity had been assured. The static photoelastic hybrid method was applied to the Minimum Strain Energy Density Criterion, the Maximum Tangential Stress Criterion and Mode Mixity. Crack propagation criterion by the static photoelastic hybrid method was introduced and it was applied to the above various failure theories. Comparing the experimental initial angle of crack propagation with the theoretical initial angle of crack propagation from the various failure criterions. And then the optimal crack propagation criterion was suggested and it's validity was assured.

• 대한기계학회논문집A
• /
• 제29권10호
• /
• pp.1384-1391
• /
• 2005

Damage often occurs on the surface of railway wheels due to wheel-rail contact fatigue. It should be removed before reaching wheel failure, because wheel failure can cause derailment with loss of life and property. The increase or decrease of the contact fatigue lift by the metal removal of the contact surface were investigated by many researchers, but they have not considered initial residual stress and traction force. The railway wheel has the initial residual stress formed during the manufacturing process, and the residual stress is changed by thermal stress induced by braking. The traction force and residual stress are operated on wheels of locomotive and electric motor vehicle. In this study, the effect of metal removal depth on the contact fatigue life for a railway wheel has been evaluated by applying lolling contact fatigue test. The effect of the traction force and metal removal on the contact fatigue life has been estimated by finite element analysis. It has been found that the initial residual stress determines the amount of metal removal depth if the traction coefficient is less than 0.15. If the traction coefficient is greater than 0.2, however, the amount of metal removal depth is independent on the intial residual stress.

• International Journal of Concrete Structures and Materials
• /
• 제11권1호
• /
• pp.161-169
• /
• 2017

Flat slab systems are vastly used in multi-story buildings because of their savings in story height and construction time, as well as for their flexibility in architectural remodeling. However, they frequently suffer brittle punching-shear failure around columns, especially when subjected to lateral loads. Therefore, seismic codes labeled flat slabs as non-ductile systems. This research goal is investigating some construction alternatives to enhance flat slab ductility and deformability. The alternatives are: adding different types of punching-shear reinforcement, using discreet fibers in concrete mixes, and increasing thickness of slab around columns. The experimental study included preparation and testing of seven half-scale interior slab-column connections up to failure. The first specimen is considered a reference, the second two specimens made of concrete mixes with different volumetric ratios of polymer fibers. Another three specimens reinforced with different types of punching-shear reinforcement, and the last specimen constructed with drop panel of inverted pyramidal shape. It is found that using the inverted pyramid-shape drop panel of specimen, increases the punching-shear capacity, and the initial and the post-cracking stiffnesses. The initial elastic stiffnesses are different for all specimens especially for the slab with closed stirrups where it is experienced the highest initial stiffness compared to the reference slab.