• Journal of Advanced Research in Ocean Engineering
• /
• 제1권4호
• /
• pp.211-226
• /
• 2015

Membrane type Mark III cargo containment system (CCS) is considered in this study to investigate its strength capability under applied loads due to liquefied natural gas (LNG) cargo. A rectangular plated structure supported by inner hull structure is exemplified from Mark III CCS according to classification society's guidance and it is assumed as multi-layered structure by stacking plywood, triplex, reinforced polyurethane (PU) foam and series of mastic upon inner hull structure. Commercially available general purpose finite element analysis package is used to have reliable FE models of Mark III CCS plate. The FE models and anisotropic failure criteria such as maximum stress, Hoffman, Hill, Tsai-Wu and Hashin taking into account the direction dependent material properties of Mark III CCS plate components and their material properties considering a wide variation of temperature due to the nature of LNG together form the strength analysis procedure of Mark III CCS plate. Strength capability of Mark III CCS plate is understood by its initial failure and post-initial failure states. Results are represented in terms of failure loads and locations when initial failure and post-initial failures are occurred respectively. From the results the basic design information of Mark III CCS plate is given.

• Journal of the Korean Recycled Construction Resources Institute
• /
• 제11권3호
• /
• pp.177-183
• /
• 2023

Various failure modes occur in the concrete beams reinforced with GFRP(Glass Fiber Reinforced Plastic) under initial condition and repairing patterns. In this study, the failure behaviors of concrete beams restrengthened with GFRP sheet with slightly higher elastic modulus than concrete were investigated. For the tests, concrete beams with 24 MPa were manufactured, and the effects of initial notch, overlapping, end-strip reinforcement, and fiber anchors were analyzed on failure load. The cases of GFRP overlap around notch and the initial notch showed increasing failure loads similar to those of normal restrengthened case since the epoxy of the saturated GFRP sufficiently repaired the notch area. Compared to the control case without restrengthening of GFRP, the concrete with initial notch showed 0.78 of loading ratio and normal restrengthening showed 4.43~5.61 times of increasing ratio of failure loading, where interface-debonding from flexural crack were mainly observed. The most ideal failure behavior, break of GFRP, was observed when end-strip over 1/3 height from bottom and fiber anchor were installed, which showed increasing failure load over 150 % to normal restrengthening.

• Korean Journal of Head & Neck Oncology
• /
• 제21권1호
• /
• pp.26-31
• /
• 2005

Backgrounds and Objectives: Squamous cell carcinomas of the oral cavity(SCOC) in TNM stage I & II have relatively high chance to be cured compared to those in the advanced stage, but sometimes result in the treatment failure with poor prognosis. There have been few reports on the patterns of failure and the clinical courses for SCOC in stage I & II after the failure of initial treatment. This study is directed at identifying the clinical outcomes of stage I & II SCOC and the salvage rate after initial treatment and suggesting an optimal level of treatment by analyzing the patterns of failure. Material and Methods: The medical records of 36 patients with SCOC, initially diagnosed between 1995 and 2001 as TNM stage I & II were reviewed retrospectively. The patterns of failure, salvage treatment, clinical courses, and the survival of these subjects were analyzed. The minimum follow-up period of no-evidence of disease(NED) was 12 months with an average of 32.2 months. Results: Overall rate of the treatment failure in SCOC of stage I & II was 41. 7%(15/36 cases). Most of the treatment failure in the subjects with stage I tumors occurred in regional lymph node. Local failure was the most frequent form of failure in the subjects with stage II tumors after wide excision of primary tumor with elective neck dissection and/or radiation therapy. No significant correlation was noted between the safety margin and the local failure. Elective neck dissections in stage I & II SCOC had a tendency to reduce regional failure (p=0.055). The salvage rates at 24 months were 85.7% in stage I, and 37.5% in stage II. The 3-year survival rate after the failure of initial treatment was 55.0%. Conclusion: SCOC of stage I & II after the failure of initial treatment showed poor prognosis despite of the salvage treatments. This study implies that the elective neck dissections for regional lymph node should be required for SCOC of stage I & II to reduce the treatment failure.

• Proceedings of the Korea Concrete Institute Conference
• /
• 한국콘크리트학회 1998년도 봄 학술발표회논문집(II)
• /
• pp.585-591
• /
• 1998

In the case of reinforced concrete beams strengthening by steel plate, sometimes these beams collapse due to the stress concentration at the ends of steel plates before the design expected failure. This kind of failure is called premature failure. This study analyzes the behavior of strengthened RC beams to control premature failure of these plated beams with either changing the geometries at the ends of plates or strengthening steel plates beside the ends. The results from the former cases show that, the effect of expanded plates sections at the ends was very small, and the beams which are rounded the ends of plates effectively increased the initial rip-off loads about 14% compared with control beam but the ultimate loads was almost same. However, the beams in the latter cases effectively increased the initial and the ultimate rip-off loads with changing failure mode, especially around 14~19% in the ultimate rip-off load comparing with control beam.

• Proceedings of the KSME Conference
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1792-1797
• /
• 2007

This paper try to find root-cause of failure in a connector used in transmitting signals for throttle body control in automotives by analyzing possible failure causes and performing experiments to simulate the cable failure in field. The connector comprises fins, wires, and case moldings. The failure is due to degradation of initial clamping force required fixing fins and wires in the connector. Expansion and compression of the case molding material surrounding fins would cause the degradation. Investigations of strict initial claming force and control of thermal expansion property of the molding are required to prevent the failure.

• Journal of The Korean Society of Clinical Toxicology
• /
• 제7권2호
• /
• pp.83-89
• /
• 2009

Purpose: Rhabdomyolysis is one of the most important complications of pesticide intoxication. It affects a patient's clinical prognosis and can cause acute renal failure. It is important that patients diagnosed with pesticide intoxication receive an accurate initial diagnosis and proper treatment to prevent significant complications. This study's objective was to investigate and confirm related factors causing acute renal failure by verifying clinical observations and laboratory findings collected following pesticide intoxication. Methods: A retrospective analysis was made of 734 patients who presenting to our emergency medical center after ingesting pesticides between January 2006 and December 2008, Of these, 513 patients were selected for the study. Two hundred and twenty-one patients were excluded because of paraquat intoxication, age (if under 18), or chronic renal failure. Seventy-four patients were diagnosed with rhabdomyolysis, based on serum creatinine phosphokinase levels were > 1,000U/L. Acute renal failure was diagnosed when creatinine levels were > 2.0 mg/dL. Results: Among the 74 patients diagnosed with rhabdomyolysis, 26 (35.1%) experienced acute renal failure. The most meaningful related factor in the prediction of acute renal failure was initial arterial pH and creatinine level. Conclusion: Initial arterial pH and creatinine level are predictors of complications such as acute renal failure in patients with rhabdomyolysis.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 한국공작기계학회 2004년도 춘계학술대회 논문집
• /
• pp.275-280
• /
• 2004

Shape optimization was performed to obtain the precise shape of cutouts including the internal shape of cutouts in laminated composite plates by three dimensional modeling using solid element. The volume control of the growth-strain method was implemented and the distributed parameter chosen as Tsai-Hill fracture index for shape optimization. The volume control of the growth-strain method makes Tsai-Hill failure index at each element uniform in laminated composites under the initial volume. Then shapes optimized by Tsai-Hill failure index were compared with those of the initial shapes for the various load conditions and cutouts. The following conclusions were obtained in this study. (1) It was found that growth-strain method was applied efficiently to shape optimization of three dimensional cutouts in a laminate composite, (2) The optimal shapes of the various load conditions and cutouts were obtained, (3) The maximum Tsal-Hill failure index was reduced up to 67% when shape optimization was peformed under the initial volume by volume control of growth-strain method.

• Journal of the Korean Geotechnical Society
• /
• 제22권5호
• /
• pp.83-91
• /
• 2006

Recently, the intensive rainstorm possibly induced by global warming plays a key role on the instability of railway adjacent slopes. The instability of slopes results as covering and loss of railway lines induced by slided soil mass. According to the site investigation on the failed slopes triggered by rainfall, low types of slope failure were observed: shallow, intermediate, gully erosion, and soil-rock interface failures. The observation reveals the different characteristics of slope failure depending on the thickness of soil layer, morphological features of slope, etc. Based upon the observations, flume tests were conducted to analyze the sliding mechanism of each failure. The variables of flume test are soil layer thickness, rainfall intensity, and morphology of slope under the constant condition of the percentage of fine, initial soil moisture content, slope angle and compaction energy. Test results show that shallow failure was mostly observed from the surface of the slope and caused by the soil erosion; in addition, compared to the other types of failure, the occurrence of initial erosion is late, however, the development of erosion is fast. In gully erosion failure, the collected water from the water catchment area helps erosion of the upper soil layer and transfer of residual corestone, which impedes the erosion process once the upper soil layers are eroded and corestone are exposed. The soil-rock interface failure shows the most fast initial erosion process among the failure types. Interestingly, the common feature observed from the different types of failure was the occurrence of the initial deformation near the toe of slopes which implies the existence of surbsurface flow along the downslope direction.

• Journal of the Korean institute of surface engineering
• /
• 제31권1호
• /
• pp.34-44
• /
• 1998

Stainless steel is being used widely lor various purposes due to its good corrosion resistance. There has becn much research to produce colored stainless sterl by several methods. In this experiment, we coated TixN film on the SUS304 substrate with thc DC magnetron sputtering system and studied the internal structurc and adhesive strength of the films as a function of the coating conditions. Before lhe specimen was coated, a sputter etching was very effective in removing the$\delta$ Fe(BCC) phase as well as the contaminant and oxide layer as well as increasing rotghness. Five-stage failure mode appeared with increased scratch load with the TIN films coated on the SUS304 in this manner ; tensile failure-,conformal failure-,buckling failure->chipping failurc and spalling Failure. When the failure was terminated at the initial stage, the film will have good adhesion. But, if syalling failure has occurred at the initial scratch, then the adhesion will be poor. The interlayer between thc coated film and thc substratc was homogeneously adhcsive when the $\gamma'-Fe_4N$ phase wasn't detected in the XRD analysis and the adhesive strength only was reduced by surPace defects. But, when the ,$\gamma'-Fe_4N$N phasc was detected in the XRD analysis, the adhesive strength was very poor.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• 제13권4호
• /
• pp.16-22
• /
• 2004

Shape optimization was performed to obtain the precise shape of cutouts including the internal shape of cutouts in laminated composite plates by three dimensional modeling using solid element. The volume control of the growth-strain method was implemented and the distributed parameter chosen as Tsai-Hill fracture index for shape optimization. The volume control of the growth-strain method makes Tsai-Hill failure index at each element uniform in laminated composites under the initial volume. Then shapes optimized by Tsai-Hill failure index were compared with those of the initial shapes for the various load conditions and cutouts. The following conclusions were obtained in this study (1) It was found that growth-strain method was applied efficiently to shape optimization of three dimensional cutouts in a laminated composite plate, (2) The optimal shapes on the various load conditions and cutouts were obtained, (3) The maximum Tsai-Hill failure index was reduced up to 67% when shape optimization was performed under the initial volume by volume control of growth-strain method.