• 한국표면공학회지
• /
• 제49권3호
• /
• pp.280-285
• /
• 2016

In this study, we investigated the influences of potassium fluoride(KF) addition on the surface characteristics of plasma electrolytic oxidation(PEO) coating produced on Al alloy. The PEO of marine grade Al alloy(5083 grade) was conducted in KOH 1g/L solution adding different concentrations of KF(0, 1 and 2 g/L) under a galvanostatic regime. With KF addition, unusual behavior was observed on the voltage-time characteristic curves, which can be characterized by the following process: (i) initial rapid increase in voltage (ii) a short plateau after 1st breakdown (iii) gradual increase in voltage (iv) intermittent fluctuation of voltage after 2nd breakdown. The SEM observation revealed irregular surface morphology with KF addition, as compared with one formed without KF addition, which had a reticulate structure. The XRD analysis detected the formation of aluminium hydroxide fluoride hydrate($H_{4.76}Al_2F_{3.24}O_{3.76}$) on surface grown by PEO process with KF. Particularly, at very early stage of the process (~ 120 s), thin film was formed having nanoporous structure, and F element was confirmed on surface by EDS analysis. The thickness and surface roughness of the coating increased with increasing KF concentration. As a result, KF addition was found to be less beneficial influences on PEO of marine grade Al alloy, and therefore needs further research to improve its capability.

• 대기
• /
• 제28권4호
• /
• pp.479-490
• /
• 2018

This study assesses the prediction skill of regional scale model for the mean temperature anomaly over South Korea produced by Pusan National University Coupled General Circulation Model (PNU CGCM)-Weather Research and Forecasting (WRF) chain. The initial and boundary conditions of WRF are derived from PNU CGCM. The hindcast period is 11 years from 2007 to 2017. The model's prediction skill of mean temperature anomaly is evaluated in terms of the temporal correlation coefficient (TCC), root mean square error (RMSE) and skill scores which are Heidke skill score (HSS), hit rate (HR), false alarm rate (FAR). The predictions of WRF and PNU CGCM are overall similar to observation (OBS). However, TCC of WRF with OBS is higher than that of PNU CGCM and the variation of mean temperature is more comparable to OBS than that of PNU CGCM. The prediction skill of WRF is higher in March and April but lower in October to December. HSS is as high as above 0.25 and HR (FAR) is as high (low) as above (below) 0.35 in 2-month lead time. According to the spatial distribution of HSS, predictability is not concentrated in a specific region but homogeneously spread throughout the whole region of South Korea.

• 천문학회보
• /
• 제44권1호
• /
• pp.53.2-53.2
• /
• 2019

$H{\alpha}$ surges (i.e. cool/dense collimated plasma ejections) may act as a guide for a propagation of magnetohydrodynamic waves. We report a high-resolution observation of a surge observed with 1.6m Goody Solar Telescope (GST) on 2009 August 26, from 18:20~UT to 18:45UT. Characteristics of plasma motions in the surge are determined with the normalizing radial gradient filter and the Fourier motion filter. The shape of the surge is found to change from a 'C' shape to an inverse 'C' shape after a formation of a cusp, a signature of reconnection. There are apparent upflows seen above the cusp top and downflows below it. The upflows show rising and rotational motions in the right-hand direction, with the rotational speed decreasing with height. Near the cusp top, we find a transverse oscillation of the surge, with the period of ~2 min. There is no change of the oscillation phase below the cusp top, but above the top a phase change is identified, giving a vertical phase speed about 86kms-1. As the height increases, the initial amplitude of the oscillation increases, and the oscillation damping time decreases from 5.13 to 1.18min. We conclude that the oscillation is a propagating kink wave that is possibly excited by an x-point oscillation.

• 한국재료학회지
• /
• 제31권1호
• /
• pp.38-42
• /
• 2021

In this study, high temperature wetting analysis and AZ80/Ti interfacial structure observation are performed for the mixture of AZ80 and Ti, and the effect of Al on wetting in Mg alloy is examined. Both molten AZ80 and pure Mg have excellent wettability because the wet angle between molten droplets and the Ti substrate is about 10° from initial contact. Wetting angle decreases with time, and wetting phenomenon continues between droplets and substrate; the change in wetting angle does not show a significant difference when comparing AZ80-Ti and Mg-Ti. As a result of XRD of the lower surface of the AZ80-Ti sample, in addition to the Ti peak of the substrate, the peak of TiAl3, which is a Ti-Al intermetallic compound, is confirmed, and TiAl3 is generated in the Al enrichment region of the Ti substrate surface. EDS analysis is performed on the droplet tip portion of the sample section in which pure Mg droplets are dropped on the Ti substrate. Concentration of oxygen by the natural oxide film is not confirmed on the Ti surface, but oxygen is distributed at the tip of the droplet on the Mg side. Molten AZ80 and Ti-based compound phases are produced by thickening of Al in the vicinity of Ti after wetting is completed, and Al in the Mg alloy does not affect the wetting. The driving force of wetting progression is a thermite reaction that occurs between Mg and TiO2, and then Al in AZ80 thickens on the Ti substrate interface to form an intermetallic compound.

• Pediatric Gastroenterology, Hepatology & Nutrition
• /
• 제24권2호
• /
• pp.135-144
• /
• 2021

Purpose: Although ultrasonography is the gold standard of diagnosing intussusception, plain abdomen radiograph (AXR) is often used to make differential diagnosis for pediatric patients with abdominal pain. In intussusception patients, we aimed to analyze the AXR and clinical data to determine the characteristics of early AXR findings associated with diagnosis of intussusception and recurrence after reduction. Methods: Between January 2011 and June 2018, 446 patients diagnosed with intussusception based on International Classification of Diseases-10 code of K56.1 were admitted. We retrospectively reviewed medical records of 398 patients who received air reduction; 51 of them have recurred after initial reduction. We evaluated six AXR features including absent ascending colon gas, absent transverse colon gas, target sign, meniscus sign, mass, and ileus. Clinical data and AXR features were compared between single episode and recurrence groups. Results: Two groups did not show significant differences regarding clinical data. Mean time to recurrence from air reduction was 3.4±3.2 days. Absent ascending colon gas (63.9%) was the most common feature in intussusception, followed by mass (29.1%). All of six AXR features were observed more frequently in the recurrence group. Absent transverse colon gas was the most closely associated AXR finding for recurrence (odds ratio, 2.964; 95% confidence interval, 1.327-6.618; p=0.008). Conclusion: In our study, absence of ascending colon gas was the most frequently seen AXR factor in intussusception patients. Extended and careful observation after reduction may be beneficial if such finding on AXR is found in intussusception patients.

• 한국콘텐츠학회논문지
• /
• 제22권4호
• /
• pp.700-705
• /
• 2022

혈우병은 혈액 응고에 필요한 13개의 인자들 중 1개라도 결핍될 경우 혈액 응고에 장애가 발생하여 지혈 이상을 보이는 선천성 출혈성 질환이다. 13개의 인자들 중 결핍된 응고 인자에 따라 혈우병 A(제8번 인자, factor VIII), 혈우병 B(제9번 인자, factor IX), 혈우병 C(제10번 인자, factor X)로 분류된다. 혈우병 A 진단을 받은 40대 남성 환자가 전체적인 만성 치아 주위 염증으로 인한 치조골 흡수 및 치주농양을 문제를 주소로 을지대학교병원 치과에 내원하였고, 초진당시 전반적인 골흡수 및 염증상태를 보였다. 혈액응고인자의 농도를 적절히 유지하며 관혈적 및 비관혈적 치료를 시행한 바, 10년 동안의 정기적인 내원으로 #35, #36 부위를 제외한 나머지 부위에서 별다른 합병증이나 출혈성향은 관찰되지 않았고, 전반적으로 양호한 구강 상태를 보였으며 부작용이나 합병증은 보이지 않았다.

• 열처리공학회지
• /
• 제34권3호
• /
• pp.122-129
• /
• 2021

This study focuses on the microstructural development of 99% magnesium alloy sheet manufactured using twin roll casting (TRC) process. Herein, a plate with a thickness of 5 mm was manufactured using the TRC process, homogenization heat treatment was performed at 400℃ for 2-32 h, and finally, the change in microstructure was evaluated via optical microscopy and textural analysis. The results suggest that the plate manufactured using the TRC process was not destroyed and was successfully rolled into a plate. Microscopic observation suggested that the dendritic cast structure was arranged along the rolling direction. And the central layer of the rolled plate, where was present in a liquid state at the beginning of rolling, solidified later during the TRC process to form central segregation. The initial cast structure and inhomogeneous structure of the plate were recrystallized by homogenization heat treatment for only 2 h, and it was confirmed that the segregated part of the central layer became homogeneous and recrystallization occurred. Grain growth occurred as the heat treatment time increased, and secondary recrystallization occurred, wherein only some grains were grown. The textural analysis, which was conducted via X-ray diffraction, confirmed that the relatively weak basal plane texture developed using the TRC process was formed into a random texture after heat treatment.

• Asian Pacific Journal of Cancer Prevention
• /
• 제15권17호
• /
• pp.7079-7083
• /
• 2014

The International Prostate Symptom Score (IPSS) is often used as an interview sheet for assessing lower urinary tract symptoms (LUTS) at the time of prostate-specific antigen (PSA) testing during population-based screening for prostate cancer. However, the relationship between prostate cancer detection and LUTS status remains controversial. To elucidate this relationship, the cumulative probability of prostate cancer detection using IPSS in biopsy samples from patients categorized by serum PSA levels was investigated. The clinical characteristics of prostate cancer detected using IPSS during screening were also investigated. A total of 1,739 men aged 54-75 years with elevated serum PSA levels who completed the IPSS questionnaire during the initial population screening in Kanazawa City, Japan and underwent systematic transrectal ultrasonography-guided prostate biopsy between 2000 and 2013 were enrolled in the present study. Of the 1,739 men, 544 (31.3%) were diagnosed with prostate cancer during the observation period. The probability of cancer detection at 3 years in the entire study population was 27.4% and 32.7% for men with $IPSS{\leq}7$ and those with $IPSS{\geq}8$, respectively; there was no statistically significant difference between groups. In men with serum PSA levels of 6.1 to 12.0ng/mL at initial screening, the probability of cancer detection was significantly higher in men with $IPSS{\leq}7$ than in those with $IPSS{\geq}8$. There were no significant differences in clinical characteristics between groups of patients stratified by IPSS. These findings indicate that the use of IPSS for LUTS status evaluation may be useful for prostate cancer detection in the limited range of serum PSA levels.

• 한국물환경학회지
• /
• 제23권1호
• /
• pp.138-143
• /
• 2007

This study goes in for the observation of the characteristics of nitrogen removal from swine wastewater by struvite crystallization. In addition, the struvite formation potential in supernatants after struvite crystallization was investigated. In the study for nitrogen removal by struvite crystallization, the effects of pH and molar ratio of magnesium (Mg) injected using bittern as Mg source were investigated. Also, the potential of struvite formation in the supernatant with amount of Mg added was carefully observed. As the results, the optimum pH in the removal of nitrogen was 8.8 and sludge volume was increased as pH was raised from 7 to 12 under the condition that the molar ratio of $Mg^{2+}$ to ${NH_4}^+$-N to ${PO_4}^{3-}$-P was 1:1:1. An optimum removal efficiency of ammonia-N was observed at 1 molar ratio of Mg to ${NH_4}^+$-N, showing no further increase at over 1 molar ratio and dramatical deterioration at under 1 molar ratio. However, the sludge volume was increased by increasing the molar ratio of Mg. In the experiments for the potential of struvite formation in the supernatants, initial -log([$Mg^{2+}$][${NH_4}^+$][${PO_4}^{3-}$]) value was much lower than $pK_{sp}$ and gradually reached $pK_{sp}$ at 2 days, as the molar ratio of Mg increased over 1.2. At 31 days, -log([$Mg^{2+}$][${NH_4}^+$][${PO_4}^{3-}$]) value was returned to the initial value. In addition, the supernatants had a potential precipitation of hydroxylapatite due to calcium contained in bittern, $K_2Mg(SO_4)_3$ and $K_3Na(SO_4)_2$ resulting from the decrease of sodium and potassium in supernatants formed after struvite crystallization as times go by. Based on the results, it appears that some retention time and proper dosage of Mg may be needed for the prevention of scale in pipe line.

• 대기
• /
• 제29권5호
• /
• pp.671-687
• /
• 2019

This study evaluates the long-term seasonal predictability of summer (June, July and August) heatwaves over South Korea using 30-year (1989~2018) Hindcast data of the Pusan National University Coupled General Circulation Model (PNU CGCM)-Weather Research and Forecasting (WRF) chain. Heatwave indices such as Number of Heatwave days (HWD), Heatwave Intensity (HWI) and Heatwave Warning (HWW) are used to explore the long-term seasonal predictability of heatwaves. The prediction skills for HWD, HWI, and HWW are evaluated in terms of the Temporal Correlation Coefficient (TCC), Root Mean Square Error (RMSE) and Skill Scores such as Heidke Skill Score (HSS) and Hit Rate (HR). The spatial distributions of daily maximum temperature simulated by WRF are similar overall to those simulated by NCEP-R2 and PNU CGCM. The WRF tends to underestimate the daily maximum temperature than observation because the lateral boundary condition of WRF is PNU CGCM. According to TCC, RMSE and Skill Score, the predictability of daily maximum temperature is higher in the predictions that start from the February and April initial condition. However, the PNU CGCM-WRF chain tends to overestimate HWD, HWI and HWW compared to observations. The TCCs for heatwave indices range from 0.02 to 0.31. The RMSE, HR and HSS values are in the range of 7.73 to 8.73, 0.01 to 0.09 and 0.34 to 0.39, respectively. In general, the prediction skill of the PNU CGCM-WRF chain for heatwave indices is highest in the predictions that start from the February and April initial condition and is lower in the predictions that start from January and March. According to TCC, RMSE and Skill Score, the predictability is more influenced by lead time than by the effects of topography and/or terrain feature because both HSS and HR varies in different leads over the whole region of South Korea.