• 한국세라믹학회지
• /
• 제35권7호
• /
• pp.740-748
• /
• 1998

The inertia friction properties of C/C composites manufactured by the processes of pressure and at-mospheric carbonizaton with a commerciallized and two kinds of modified coal-tar pitch as a matrix pre-cursor were investigated. The modifications of a pitch such as the introduction of mesophase and the ad-dition of sulphur into a raw pitch were not effective for a impregnation efficiency conducted in a vacuum and at the same time in a pressure of 5kg/cm2 due to the increase of the pitch viscosity. There was not a difference in the densification increment between the pitch modifications however it was revealed that a pressure carbonization was more advantageous than an atmospheric in the densification and the formation of anisotropic carbon matrix. The friction and wear propertis of C/C having higher degree of matrix cry-stallization higher density and hardness of friction surface showed superiority. As the braking energy was increased the friction coefficients were decreased and reached almost same level at the high kinetic energy of 99.6kJ. The wear trends at 99.6kJ were different from the behaviors of friction ceofficient under the same energy in which an oxidation wear is being considered along with a mechnical wear although the wear rates were almost similar to the friction coefficient at the low energy.

• Tribology and Lubricants
• /
• 제11권2호
• /
• pp.44-55
• /
• 1995

Frictional characteristics with the change of dynamic parameters, such as stiffness, inertia and damping, in the friction measurement at dry sliding surfaces were experimentally and theoretically investigated throughout the study. Dynamic frictional force and the variation in the normal load were mainly measured at the various conditions of system dynamic parameters with which stiffness in the normal direction, loading mechanisms and test materials were varied. For the normal load, mechanisms using both a dead weight and a pneumatic cylinder were applied, which resulted in change of the inertia and damping of the test rig. Test materials were steel, rosin and PTFE, which have different types of intrinsic frictional characteristics. Test results showed that frictional characteristics under different dynamic parameters could be different even though the operating variables were the same and also they could result in the variation in the normal load, which could consequently affect the wear mechanism.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2002년도 추계학술대회 논문집(II)
• /
• pp.779-786
• /
• 2002

The Friction Brake Pad of High Speed Train is the most important parts in brake system, which is usually made of Cu-based Sintered friction material. This study has been carried out about the formulation effects of sintered friction material and made lots of sample brake pads. Then, we have done the performance test of the developed product by using full scale inertia Dynamo-meter. This performance test (braking speed 300km/h) was conducted as GEC Alsthom Standard test procedure and High Speed Brake Test (braking speed 350km/h) was done at "Poli" in Italy. The friction properties of this product was almost identical with the brake pad which is currently used to TGV. And the temperature of brake disk on braking speed 350Km/h was a little higher.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권6호
• /
• pp.34-42
• /
• 2000

In this paper conventional technique will be described, which can be used for the measuring various parameters of induction motor. This is followed by presenting some other, alternative, techniques. The two tests are described which are suitable to obtain the electrical parameters of symmetrical 1hp three-phase squirrel-cage induction motor. These are the blocked rotor test and no load test. By the application of these, it is possible to determine the parameters which are presented in the steady-state equivalent-circuit of determining an induction motor. One conventional method of determining the inertia of an induction motors is obtained by performing retardation tests. The angular rotor speed of the motor is monitored, following its disconnection from the stator supply. Since the inertia torque J dw/dt contains the inertia coefficient J and the friction and windage torque Bw contains the coefficient B, then J and B can be determined by performing retardation tests.

• 한국기계가공학회지
• /
• 제18권11호
• /
• pp.47-56
• /
• 2019

A deep neural network (DNN) model was proposed to predict the upset in the inertia friction welding process using a database comprising results from a series of FEM analyses. For the database, the upset length, upset beginning time, and upset completion time were extracted from the results of the FEM analyses obtained with various of axial pressure and initial rotational speed. A total of 35 training sets were constructed to train the proposed DNN with 4 hidden layers and 512 neurons in each layer, which can relate the input parameters to the welding results. The mean of the summation of squared error between the predicted results and the true results can be constrained to within 1.0e-4 after the training. Further, the network model was tested with another 10 sets of welding input parameters and results for comparison with FEM. The test showed that the relative error of DNN was within 2.8% for the prediction of upset. The results of DNN application revealed that the model could effectively provide welding results with respect to the exactness and cost for each combination of the welding input parameters.

• Journal of Power Electronics
• /
• 제16권4호
• /
• pp.1387-1395
• /
• 2016

A method for the identification of mechanical parameters based on integral calculation is presented. Both the moment of inertia and the friction constant are identified by the method developed here, which is based on well-known mechanical differential equations. The mechanical system under test is excited according to a pre-determined low-frequency sinusoidal motion, minimizing the distortion, and increasing the accuracy of the results. The parameters are identified using integral calculation, increasing the robustness of the results against measurement noise. Experimental data are supported by simulation, confirming the effectiveness of the proposed technique. The performance improvements shown here are of use in the design of speed and position controllers and observers. Owing to its simplicity, this method can be readily applied to commercial inverter products.

• 한국항공우주학회지
• /
• 제44권11호
• /
• pp.981-988
• /
• 2016

브레이크 동력계는 브레이크의 성능을 시험하는 장치로 시험구역, 기계적 관성구역, 전기모터 및 제어구역으로 구성된다. 혼성동력계는 기계적 관성 구역의 크기를 줄이고 전기모터를 이용하여 브레이크 작동에 따른 기계적 관성의 손실을 보상하는 방식으로 상대적으로 작은 기계적 관성 크기와 적은 비용으로 시험이 가능한 장점이 있다. 본 논문에서는 공간적 제약이 있는 실험실에 적절한 혼성동력계를 설계하였고, 설계된 혼성동력계에서 마찰계수 변화 등 주요 설계변수가 혼성동력계 제동성능에 미치는 영향을 분석하였다. 본 연구를 통해 축소된 기계적 관성에 의한 에너지 손실을 보상하기 위한 전기 모터의 토크를 측정하면 마찰재의 불량여부를 판단 할 수 있는 결과를 얻었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.1082-1083
• /
• 2007

Electric motors are widely used from precision industry to home appliance. For the precision control of the motors, if it is possible, we need the information of the correct motor parameters. In the motor torque equation, the motor inertia moment and the viscosity friction coefficient are regarded as constant. However the viscosity friction coefficient is not constant in the real system. In this paper, we show that the viscosity friction coefficient has the nonlinear property through the real test and we present the nonlinear function for the viscosity friction coefficient.

• 농업과학연구
• /
• 제40권3호
• /
• pp.237-241
• /
• 2013

This study started to export an orchard tractor to Europe under the situations that R&D activities for orchard tractor were marginal and even it was not produced. The R&D for orchard tractor has been progressed and the most of it is accomplishing the goal. In this study, the durability of clutch friction part was tested for F/R clutch and moment of inertia of PTO clutch, and it was compared with the design criteria of transmission of tractor. According to the results of inertia test of F/R clutch, hydraulic pressures of clutch satisfied $1,961.33{\pm}196.13kPa$ of design criteria, and the variations of torque for forward and reverse operation were relatively constant. Therefore, it was found that the durability of clutch friction part was stable and reliable. Test results showed that the main hydraulic pressures were maintained $1,961.33{\pm}196.13kPa$ during the tests of moment of inertia of PTO clutch, and when it was operated, the hydraulic pressures were reached $1,961.33{\pm}196.13kPa$. Therefore, it was found that the hydraulic pressures of PTO satisfied the design criteria. By the results that the time of the hydraulic pressures of PTO reaching main hydraulic pressure, and that of torque values restoring to the original was same as the time of the first gear of PTO reaching the maximum rotational speed, it was found that PTO could transfer power to attachments as it was designed.

• 한국소음진동공학회논문집
• /
• 제16권10호
• /
• pp.1067-1073
• /
• 2006

In this paper, we present noise measurement results of 8 vehicles. The measurement was done by a close proximity method attaching surface microphones on the test vehicle. For the 9 road surface types constructed at Korean highway test road, the vehicles were tested from 50 to 120 km/h at the interval of 10 km/h in normal steady state and inertia cruising conditions. Using the results, we evaluate and discuss the effect of vehicle noise generation depending on the different conditions for vehicle type, speed, road surface and loading condition, especially focused on friction noise between tyre and road surface.