• Journal of Korean Society for Atmospheric Environment
• /
• v.18 no.3
• /
• pp.231-245
• /
• 2002

A better knowledge of emission inventories can serve several important functions such as provision of public information, identification of primary sources, assessment of temporal and spatial trend, and analysis for national modelling studies. The purpose of this paper is to propose the new air emission source categories on the basis of the Korea Standard Industrial Classification. Hence, the paper focuses on reviewing and comparing the air emission sources categories of USEPA, and EU. The new emission source categories compose Tiers 1, 2, and 3. For Tier 1, there are 14 categories; fuel combustion-utilities, industries, and heating and others, chemical and allied product manufacturing, metals processing, and petroleum and related industries, etc. Tier 2 consists of small categories classified minutely in Tier 1. Tier 3 connects the categories of Tier 2 with the Korea Standard Industrial Classification.

• Industrial Engineering and Management Systems
• /
• v.15 no.1
• /
• pp.99-109
• /
• 2016

During the last two decades, impact factor has been widely used as a journal evaluation metric that differentiates the influence of a specific journal compared with other journals. However, impact factor does not provide a reliable metric between journals in different subject categories. For example, higher impact factors are given to biology and general sciences than those assigned to other traditional engineering and social sciences. This study initially analyzes the trend of the time series of the impact factors of the journals listed in Journal Citation Reports during the last decade. This study then proposes new journal evaluation metrics that adjust the impact factors across different subject categories. The proposed metrics possibly provides a consistent measure to mitigate the differences in impact factors among subject categories. On the basis of experimental results, we recommend the most reliable and appropriate metric to evaluate journals that are less dependent on the characteristics of subject categories.

• Journal of Korean Society on Water Environment
• /
• v.26 no.2
• /
• pp.191-199
• /
• 2010

Introduction of Technology-Based Effluent Limitations (TBELs) concepts into Korea requires extensive and through analyses on the expected pollutants reduction effects and the cost factor for the industry side. In addition, the TEBLs should be optimized for the regulatory environments of Korea and be applied in a progressive manner to minimize the undesirable effects. It is also necessary to assess the contribution of each industrial categories's to the pollution of natural water bodies to find the priority of TEBLs application. For these purposes, the pollution loads of various industrial categories were analyzed using risk assessment indicator based on Toxic Weighting Factors (TWFs). First, the TWFs were calculated for the pollutants regulated using the method adopted by USEPA. And the effluent characteristics of the eighty two categories of industry in Korea were investigated. Although the analytical data on the wastewater from different industrial categories are relatively limited, the results from two previous studies were used. The first study, conducted by the National Institute of Environmental Research in 2001~2004, investigated the wastewater characteristics from 255 industrial sources covering the major 20 industrial categories. The second study includes more recent analytical data for the wastewater from 500 industrial sources, covering all the 82 industrial categories. In the result of the pollution loads analyses, the category of 'Synthetic and Chemical manufacture' was found to show the highest raw pollution load. On the other hand the category of 'Ion & Steel manufacture' was found to show the highest effluent pollution loads, which can be considered as the real impacts on natural water streams. The top five categories occupied 62.2% of the total effluent pollution loads. Through the analyses, the relative importances of each industrial categories and the priorities of TEBL-based pollution reduction were determined.

• Journal of Korean Society of Water and Wastewater
• /
• v.31 no.5
• /
• pp.447-457
• /
• 2017

This study derived the unit of industrial water usage reflecting the latest industry trends. Available for establishing plans such as the master plan for water supply system and analyzed changes in the basic unit by a comparison with the current basic unit values. This study analyzed 4,038 samples with a sampling error of less than 1.5 % at the 95 % confidence level after removing outliers according to a log-normal distribution. As a result, the unit of industrial water usage per site area in the whole manufacturing industry was 7.11 m3/1,000m2/d. The ten industrial categories (C10, C13, C20, C21, C22, C25, C27, C30, C32, C33) showed a similar unit value compared to before, and the four industrials categories (C11, C17, C22, C31) showed a more unit value than before. With regard to the nine industrial categories (C14, C15, C16, C18, C19, C24, C26, C28, C29), the unit value decreased. Cases that companies examined before were the same as the companies examined in this study were analyzed. The result that the changes in the unit industrial water usage were reasonable was obtained. However, in some industrial categories (C17, C14, C24, C29), the unit value was changed by a small number of companies with large-scale water use or unit value of sampling had a large deviation. It was considered necessary to survey them periodically. The unit of industrial water usage derived by the survey in this study reflects the current industrial trends in 2016. Water use in manufacturing companies has continuously changed by the development of manufacturing technologies and simplification of manufacturing processes. In order to deal with this, it is considered necessary to survey the usage of industrial water periodically from a long-term perspective.

• Environmental Engineering Research
• /
• v.22 no.3
• /
• pp.266-276
• /
• 2017

A life cycle impact assessment was applied in an industrial waste incineration plant to evaluate the direct and indirect environmental impacts based on toxicity and non-toxicity categories. The detailed life cycle inventory of material and energy inputs and emission outputs was compiled based on the realistic data collected from a local industrial waste incineration plant, and the Korean life cycle inventory and ecoinvent database. The functional unit was the treatment of 1 tonne of industrial waste by incineration and the system boundary included the incineration plant and landfilling of ash. The result on the variation of the impact by the unit processes showed that the direct impact was decreased by 79.3, 71.6, and 90.1% for the processes in a semi dry reactor, bag filter, and wet scrubber, respectively. Considering the final impact produced from stack, the toxicity categories comprised 91.7% of the total impact. Among the toxicity impact categories, the impact in the eco-toxicity category was most significant. A separate estimation of the impact due to direct and indirect emissions showed that the direct impact was 97.7% of the total impact. The steam recovered from the waste heat of the incineration plant resulted in a negative environmental burden.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.36 no.2
• /
• pp.25-31
• /
• 2013

This paper analyzed the management quality activities and performance based on industrial types. We divided the business into four industrial types, manufacturing industry, service industry, medical institution and public enterprise. We analyzed the differences of the elements of management quality in industrial types. The results show that leadership, measurement, analysis and knowledge management and workforce focus categories are not significant and strategic planning, customer and market focus, process management and performance categories are significant. This paper proposes the directions of management quality activities and performance according to industrial types based on these results.

• Journal of Korean Society for Quality Management
• /
• v.44 no.1
• /
• pp.17-28
• /
• 2016

Purpose: This paper reviews the papers on quality innovation issues which are published in the Journal of the Korean Society for Quality Management (KSQM) since 1965. The literature review is purposed to survey a variety of quality innovation issues Methods: We divide all of quality innovation issues into 2 categories: quality control circle, quality innovation and improvement Results: Dividing all of papers on quality innovation published in KSQM for 50 years into 2 categories, we provide a chronological roadmap for individual categories, and summarize the contents and contributions of surveyed papers Conclusion: The review paper is expected to provide future direction to improve quality innovation theory and practices in manufacturing and service industries

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.10
• /
• pp.4653-4657
• /
• 2013

The atmospheric corrosion rate were measured in Asan area for four years according to ISO 9224. The tested metals chosen as the most frequently used in industry, aluminum were copper, carbon steel, weathgering steel, and galvanized steel. The assessed corrosivity categories was 3 in average. The corrosivity categories of asan area was higher than typical rural area and even urban area, whereas it slightly lower than marine area. The results were discussed, specially as the regional climatic characteristics.

• Journal of Technology Innovation
• /
• v.16 no.2
• /
• pp.201-223
• /
• 2008

This paper studies the supply and demand of Industrial Technology Labor-force(ITL) and analyzes the determinate of ITL shortage in Korean manufacturing. We classified the industry into four categories-high technology industries, medium-high technology industries, medium-low technology industries and low technology industries-based on its R&D intensity like OECD. For the empirical analyses we use a survey data collected from 5,703 enterprises. The key findings are as follows: Firstly, a large majority of ITL is engaged in more technology-intensive industries but the categories that are exposed to more serious labor-force shortage problem are medium-high technology industries and low technology industries. Secondly, in the terms of supply factor, the ITL shortage problems are mainly due to the avoidance of ITL jobs. And the demand point, the reason is that the most of ITL are not researchers but production managers. Thirdly, the cause of imbalance between supply and demand of ITL are different by the technological categories. For example, in the high technology industries, the supply factors, such as average wage and turnover rate played more important role in the imbalance. But in the low technology industries the demand factors, such as per capita sales and the ratio of ITL in all employees were relatively much more important. Based on the findings, we discovered some political meanings such as the necessity to plan various policies to resolve the shortage problem of ITL according to the technological categories, etc.

• Journal of Korean Society for Quality Management
• /
• v.44 no.1
• /
• pp.29-42
• /
• 2016

Purpose: This paper reviews the papers on reliability issues which are published in the Journal of the Korean Society for Quality Management (KSQM) since 1965. The literature review is purposed to survey a variety of reliability issues for several categories Methods: We divide all of reliability issues into 9 categories: acceleration test, reliability estimation, system reliability, software reliability, reliability data collection and analysis method, lifetime distribution, maintenance and warranty strategy, reliability applications, and reliability applications to military area Results: Dividing all of papers on reliability published in KSQM for 50 years into 9 categories, we provide a chronological roadmap for individual categories, and summarize the contents and contributions of surveyed papers Conclusion: The review paper is expected to provide future direction to improve reliaiblity theories and applications in manufacturing and service industries