• ETRI Journal
• /
• v.26 no.1
• /
• pp.57-60
• /
• 2004

We propose an inductive compensation method for a surface-mountable 10 Gbps photoreceiver module. Since many typical 10 Gbps photoreceiver modules consist of a photodetector and low-noise pre-amplifier, the impedance mismatch between the photodetector and pre-amplifier, as well as package parasitics, may reduce the frequency bandwidth. In this paper, we inserted an inductive component between the photodetector and pre-amplifier in order to create frequency bandwidth expansion. From the measurement results, we have found that the proposed technique can increase the -3 dB bandwidth about 4.2 GHz wider compared with an uncompensated module. And, from a bit-error rate (BER) test, we observed -15.7 dB sensitivity at $10^{-12}$ BER. This inductive compensation can be implemented easily and is compatible with common manufacturing processes of photoreceiver modules.

• Journal of Magnetics
• /
• v.17 no.3
• /
• pp.210-213
• /
• 2012

To detect the surface and the opposite side cracks on iron specimen under AC and DC magnetic fields, the planar inductive coil sensors were employed. When the induced signals were measured, the planar inductive coil sensor and the magnetic field source were lifted off about 2 mm from the top surface of the specimen. AC magnetic fields and DC magnetic fields were applied to the specimens by single straight Cu coil and NdFeB permanent magnet, respectively. The detected signals at crack positions were good coincidence with those of the simulation results.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.231-231
• /
• 2009

• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.5
• /
• pp.395-400
• /
• 2008

Alternating magnetic field was used for detection of surface flaws on nonmagnetic and magnetic metallic specimens. The nondestructive sensor probe was composed of the planar coil with inductive magnetic thin film yoke as a sensing component and a single straight typed exciting coil. The planar inductive coil sensor with magnetic yoke was fabricated by sputtering, electroplating, dry etching and photolithography process. The alternative currents with the range of 0.1A to 1.0A (0.7 MHz to 1.8 MHz) were applied to the exciting coil. The specimens were prepared with the slit shaped artificial surface flaws (minimum depth and width; 0.5 mm) on metallic plate (Al; nonmagnetic metal and FeC; magnetic metal). The detected signal for the positions and shapes of surface flaws on specimens were obtained with high sensitivity and high signal to ratio. The measured output signals by the non-contacted scanning on surface of FeC specimen with micron-sized crack were converted to the images of the flaws. And these results were compared with the optical images, respectively.

• 한국정보통신설비학회:학술대회논문집
• /
• 2009.08a
• /
• pp.138-140
• /
• 2009

This paper investigates a method to remove the undesirable resonance of the rectangular power-bus structure(PBS) using an inductive layer. The equivalent surface impedance of the proposed loading is calculated for characterizing the proposed EBG geometry. The effects of the strips and the immediate surroundings are illustrated by a number of numerical experiments.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2006.04a
• /
• pp.114-114
• /
• 2006

• Journal of the Korea Institute of Building Construction
• /
• v.14 no.2
• /
• pp.163-169
• /
• 2014

Engineers in the construction field have been using bonded waterproofing sheets in an attempt to resolve the imbalance in the quality, the risk of fire, safety of workers, and environmental pollution, as well as to eliminate separate use of organic adhesives on the surface of concrete. Recently, self-laminated waterproofing sheets have been developed. The purpose of this research is to find an appropriate processing speed according to the changes in physical properties, and visual observation of the waterproofing sheets laminated by the aluminum thin-film and viscosity layer that can be attached through self-adhesiveness on the surface of concrete and waterproofing sheets. Therefore, this research is conducted using a physical performance test. Based on the result of the test, when the high-frequency inductive heating apparatus was used, an improved adhesion and bonding stability effect were confirmed after the anti-hydrostatic pressure and bond strength in the temperature condition, and the surface observation in the processing speed condition.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.3
• /
• pp.223-232
• /
• 2014

An inductive sensor system is proposed to detect the gear location and angular position of a geared shaft for automatic feeding of the shaft into the proper cutting position of the other end. The system consists of two set of coils, bridge circuit, signal condition circuit, and microprocessor. The coil sensors of the system measure changes of inductance along with the surface position of a geared shaft. The inductance changes are transformed to voltages by the bridge circuit, which are then conditioned and processed for the recognition of the gear. In order to incorporate with the experimental results with the sensor system, a finite element method (FEM) simulation for the magnetic field between the sensor and the shaft was carried out. The predicted results and the experiments revealed that the sensor system was appropriate for sensing the position of gear and the angular position of gear tooth of a geared shaft.

• Korean Journal of Materials Research
• /
• v.17 no.11
• /
• pp.618-621
• /
• 2007

Chromium nitride (CrN) films were deposited on silicon substrate by RF magnetron sputtering assisted by inductive coupled nitrogen plasma without intentional substrate heating. Films were deposited with different levels of bombarding energy by nitrogen ions $(N^+)$ to investigate the influence of substrate bias voltage $(V_b)$ on the growth of CrN thin films. XRD spectra showed that the crystallographic structure of CrN films was strongly affected by substrate bias voltage. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) results showed that surface roughness and grain size of the CrN films varied significantly with bias voltage. For - 80 $V_b$ depositions, the CrN films showed bigger grain sizes than those of other bias voltage conditions. The lowest surface roughness of 0.15 nm was obtained from the CrN films deposited at .130 $V_b$.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.3
• /
• pp.142-146
• /
• 2006

A novel internal-type linear inductive antenna, which we refer to as a double comb-type antenna, was developed for a large-area plasma source with substrate size of $880\;mm{\times}660\;mm$ ($4^{th}$ generation glass size). In this study, effect of plasma confinement by applying multi-polar magnetic field was investigated. High density plasmas of the order of $3.18{\times}10^{11}\;cm^{-3}$ could be obtained with a pressure of 15 mTorr Ar at an inductive power of 5000 W with good plasma stability. This plasma density is higher than that obtained for the conventional double comb-type antenna, possibly due to the plasma confinement, low rf voltage, resulting in high power transfer efficiency. Also, due to the remarkable reduction in the antenna rf voltage and length, a plasma uniformity of less than 3% could be obtained within a substrate area of $880\;mm{\times}660\;mm$ as rf power increased.