• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.68 no.1
• /
• pp.13-18
• /
• 2019

The domestic overhead transmission lines use a vertical configuration and reverse phase arrangement, but when there is a limitation in steel tower height because the transmission lines pass a height limit zone or special zone, an application of triangular arrangement is necessary, and a study on the optimal phase arrangement to minimize inductive interference for this is necessary. If conductor arrangement are changed, the action of electrostatic induction and electromagnetic induction becomes different from before changes, so the changed conductor arrangement should be reviewed in terms of inductive interference. So this paper presents an optimal phase arrangement to reduce inductive interference by calculating electrostatic induction and electromagnetic induction according to conductor arrangement.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.2
• /
• pp.116-125
• /
• 2003

The new HVAC system to lower the conveyance energy and building height using IAV (Increasing Air Volume) technique is developed. IAV units which are equipped in each zone carry out air-conditioning and supply fresh air by induction of outdoor air in main duct. The design program which decides size of OAHU and IAV unit according to air conditioning load and fresh air demand of each zone is presented. The control system is developed to operate efficiently HVAC system and IAV unit, so that individual zone operation and well-deal with partial load and IAQ problem are possible. The new system is investigated in model building and makes more profit in conveyance energy, size of air conditioning facilities room and building height than VAV system. But in construction cost it is worse by about 15 per-centage.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.13 no.1
• /
• pp.31-43
• /
• 2005

The new HVAC system is developed to lower the conveyance energy and building height using IAV(Increasing Air Volume) technique. IAV units which are equipped in each zone carry out air-conditioning and supply fresh air by induction of outdoor air in main duct. The design program which decides size of OAHU and IAV unit according to air conditioning load and fresh air demand of each zone is presented. The control system is developed to operate efficiently HVAC system and IAV unit, so that individual zone operation and well-deal with partial load and IAQ problem are possible. The new system is investigated in model building and makes more profit in conveyance energy. size of air conditioning facilities room and building height than VAV system. But in construction cost it is worse by about 15 percentage.

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.12
• /
• pp.1017-1021
• /
• 2015

Induction heating has been applied to the preheating process in various industrial fields. It has been used as a simple device structure, limiting the heating zone through controlled variables, and free-welding positions. It would be helpful to weld thick plates with arc welding such as GMAW. The induction heating process is well suited to this process. In this study, in order to find suitable induction heating parameters, a simulation was conducted with multi physics S/W. Three kinds of material were heated by induction coils designed specially for thick plate. Consequently, steel and nimonic alloy were the most efficient materials for preheating by induction. It can be concluded that the induction heating process is a good method for preheating the thick plate.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.6
• /
• pp.39-46
• /
• 2010

Linear induction motor is adopted as an actuator of the planar stage. An inherently poor characteristic at zero or ultra-low speed zone of the induction motor is remarkably improved due to a recent development of power electronic semiconductor technology and a spatial vector control theory. At present, a servo response speed of the induction motor reaches 90 percent of one of PM synchronous or BLDC motor. Specially, as a secondary of the induction motor can be constructed using uniform conducting sheets, there is no periodic force ripple as in PM motors. So, the induction motor can be superior to another driving means under a certain condition. This paper discusses the overall development procedure of non-contact planar stage with a big workspace using linear induction motors.

• Proceedings of the KWS Conference
• /
• 2004.05a
• /
• pp.66-68
• /
• 2004

Induction heating is a process that is accompanied with magnetic and thermal situation. When the high-frequency current flows in the coil, induced eddy current generates heat to conductor. To simulate an induction heating process, the finite element analysis program was developed. A coupling method between the magnetic and thermal routines was developed. In the process of magnetic analysis and thermal analysis, magnetic material properties and thermal material properties depending on temperature are taken into consideration. In this paper, to predict the angular deformation, temperature difference and the shape of heat affected zone were discussed. Also appropriate coil shape for maximum angular deformation were proposed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.9
• /
• pp.4156-4162
• /
• 2013

This study was peformed to determine optimum induction heating conditions for a round bar of crankshaft. Four induction heating conditions were proposed and evaluated, employing numerical method, based on electromagnetic and sequential heat transfer analyses, resulting in optimum induction heating conditions which are finally proposed based on peak temperatures at heating zone and minimum temperature gradient through thickness of a round bar after 1 hour induction heating.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.7
• /
• pp.948-954
• /
• 2004

Induction heating is a process that is accompanied with magnetic and thermal situation. When the high-frequency current flows in the coil, induced eddy current generates heat to conductor. To simulate an induction and induction heating process, the finite element analysis program was developed. A coupling method between the magnetic and thermal routines was developed. In the process of magnetic analysis and thermal analysis, magnetic material properties and thermal material properties depending on temperature are taken into consideration. In this paper, to predict the angular deformation, temperature difference and the shape of heat affected zone were discussed. Also appropriate coil shape and other process variables for maximum angular deformation were proposed.

• Journal of Welding and Joining
• /
• v.32 no.1
• /
• pp.47-52
• /
• 2014

Due to of high intensity, lower noise and easy controllability of the heat, induction heating system became well known. Induction heating method has been suggested as substitute for the gas heat source and adopted in the automation of curved hull forming system. In this study, an investigation was accomplished to find the effects on the change of material properties when the induction heating was applied on the mild steel plate. Plates were heated using weaving method to get sufficiently heat affected zone and then cooled with water or in the air. The mechanical properties of the heated plate were evaluated. As results, the tensile test, impact test and microstructures satisfied the class rule.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.6
• /
• pp.533-539
• /
• 2008

An high frequency induction hardening technology of vehicle body press-formed of thin sheet steel has been developed to increase the strength of vehicle body parts locally by high frequency induction heating, thereby eliminating the need for reinforcements. And this technique for increasing the tensile strength of sheet steel was practically applied to the front floor cross member and center pillar reinforcement of a passenger car. The side impact behavior has been investigated when induction hardening technology is applied to the conventional low-carbon steel and weight reduction of an automotive body is expected. In this paper, basic experiments were performed for the hat-shaped specimen under high frequency induction heating process. Martensitic transformation was found in the heating zone through microscopic observation which showed higher hardness. In addition, the hardness and strength of the center-pillar specimen made of boron steel increased remarkably by high frequency induction heating.