Study on the Air-bearing Stage Driven by Linear Induction Motors

선형 유도기 구동 방식 공기 베어링 스테이지에 관한 연구

  • Jung, Kwang-Suk (Department of Mechanical Engineering, Chungju National Univ.) ;
  • Shim, Ki-Bon (Graduate School, Department of Mechanical Engineering, Chungju National Univ.)
  • 정광석 (충주대학교 기계공학과) ;
  • 심기본 (충주대학교 기계공학과 대학원)
  • Received : 2010.02.03
  • Accepted : 2010.04.17
  • Published : 2010.06.01

Abstract

Linear induction motor is adopted as an actuator of the planar stage. An inherently poor characteristic at zero or ultra-low speed zone of the induction motor is remarkably improved due to a recent development of power electronic semiconductor technology and a spatial vector control theory. At present, a servo response speed of the induction motor reaches 90 percent of one of PM synchronous or BLDC motor. Specially, as a secondary of the induction motor can be constructed using uniform conducting sheets, there is no periodic force ripple as in PM motors. So, the induction motor can be superior to another driving means under a certain condition. This paper discusses the overall development procedure of non-contact planar stage with a big workspace using linear induction motors.

Keywords

References

  1. Ministry of Knowledge Economy of Korea, "Research Planning Report for Core Technology Development of Digital Lithography Equipment," 2008.
  2. Han, H. and Seo, M. H., "FPD Element Equipment - LCD Equipment," TCI Report, 2006.
  3. Jung, K. S., Park, J. K. and Kim, H. J., "Improvement of dynamic characteristic of large-areal planar stage using induction principle," J. of Institute of Control, Robotics and Systems, Vol. 15, No. 7, pp. 675-682, 2009. https://doi.org/10.5302/J.ICROS.2009.15.7.675
  4. El-Halim, A., Ashraf, M. A. and Al-Arabawy, I. F., "Design two degree of linear motion X-Y plane machine using linear induction motor," 12th Int. Middle-East Power Sys. Conf., Vol. 28, pp. 109-113, 2008.
  5. Hsu, S. and Fu, L., "Adaptive decentralized control of robot manipulators driven by current-fed induction motors," IEEE/ASME Trans. on Mechatronics, Vol. 10, No. 4, pp. 465-468, 2005. https://doi.org/10.1109/TMECH.2005.852453
  6. Dittrich, P. and Radeck, D., "3-DOF Planar Induction Motor," IEEE Int. Conf. on Electro/Information Tech., pp. 81-86, 2006.
  7. Onuki, T., Jeon, W., Hayashi, K. and Yoo, J., "Driving characteristics of x-y linear induction motor with two-dimensional primary winding," Electrical Engineering in Japan, Vol. 128, No. 2, pp. 83-90, 1999. https://doi.org/10.1002/(SICI)1520-6416(19990730)128:2<83::AID-EEJ10>3.0.CO;2-V
  8. Ohira, Y., Koseki, T. and Masada, E., "Fundamental Characteristics of an X-Y Linear Induction Motor, X-Y LIM," J. of Magnetic Society of Japan, Vol. 21, No. 5, pp. 929-934, 1997. https://doi.org/10.3379/jmsjmag.21.929
  9. Spicer, D. F., Sackett, J. N. and Black, C. T., "Precision X-Y positioning systems using linear induction motors," IEEE Colloquium on Limited Motion Electrical Actuation System, pp. 6/1-6/3, 1998.
  10. Vas, P., "Sensorless vector and direct torque control," Oxford University Press, pp. 263-379, 1996.
  11. Jung, K. S. and Lee, S. H., "The modified two-axis vector controller of linear induction motor to apply to the non-contact stage with large workspace," J. of Institute of Control, Robotics and Systems, Vol. 14, No. 4, pp. 385-391, 2008. https://doi.org/10.5302/J.ICROS.2008.14.4.385
  12. Jung, K. S. and Baek, Y. S., "Decoupling of thrust force and levitation force of transverse flux linear induction motor by the active compensation of magnetic force across the air-gap," J. of the Korean Society for Precision Engineering, Vol. 21, No. 11, pp. 91-98, 2004.