• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.4
• /
• pp.722-727
• /
• 2010

This paper presents Dynamic-Simulation to estimate the inductance of a permanent magnet type transverse flux rotating motor by applying the real-time parameter estimation theory. As transverse flux rotating motor has the complex structure, it can be happen to some errors between real value and designed one with respect to the inductance. To reduce this kinds of errors, the real-time parameter estimation theory was applied to dynamic-simulation. And then, By comparing the estimated inductance and designed one, it is realized that the real-time parameter estimation theory can be applied in the permanent magnet type transverse flux rotating motor.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.55 no.6
• /
• pp.255-258
• /
• 2006

We investigated the operating characteristics of the hybrid-type superconducting fault current limiter (SFCL) according to the inductance of secondary windings. The hybrid type SFCL consists of a transformer that has a primary winding and a secondary winding with serially connected $YBa_2Cu_3O_7$ (YBCO) films. The resistive-type SFCL has difficulty when it comes to raising the capacity of the SFCL due to slight differences of critical current densities between units and structure of the SFCL. The hybrid-type SFCL with closed-loop is able to achieve capacity increase through the electrical isolation and reduction of the inductance of the secondary winding with a superconducting element of the same critical current. On the other hand, the current limiting characteristics were nearly identical in the hybrid-type SFCL with open-loop compared to closed-loop, but quench time was longer than the hybrid-type SFCL with closed-loop. We confirmed that the capacity of the SFCL was increased effectively by the reduced inductance of the secondary winding. In addition, the power burden of the system also could be lowered by reducing the inductance of secondary winding.

• Journal of Power Electronics
• /
• v.16 no.4
• /
• pp.1256-1267
• /
• 2016

Distributed stray inductance exerts a significant influence on the turn-off voltages of power switching devices. Therefore, the design of low stray inductance bus bars has become an important part of the design of high-power converters. In this study, we first analyze the operational principle and switching transient of a T-type converter. Then, we obtain the commutation circuit, categorize the stray inductance of the circuit, and study the influence of the different types of stray inductance on the turn-off voltages of switching devices. According to the current distribution of the commutation circuit, as well as the conditions for realizing laminated bus bars, we laminate the bus bar of the converter by integrating the practical structure of a capacitor bank and a power module. As a result, the stray inductance of the bus bar is reduced, and the stray inductance in the commutation circuit of the converter is reduced to more than half. Finally, a 10 kVA experimental prototype of a T-type converter is built to verify the effectiveness of the designed laminated bus bar in restraining the turn-off voltage spike of the switching devices in the converter.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.10
• /
• pp.840-846
• /
• 2000

In this work, small-size, high-performance solenoid-type RF chip inductors utilizing a low-loss Al$_2$O$_3$core material were investigated. The size of the chip inductors fabricated in this work were 15$\times$10$\times$0.7㎣, 2.1$\times$1.5$\times$10㎣, and 2.4$\times$2.0$\times$1.4㎣ and copper (Cu) wire with 40 ㎛ diameter was used as the coils. High frequency characteristics of the inductance, quality factor, and impedance of developed inductors were measured suing an RF Impedance/Material Analyzer (HP4291B with HP16193A test fixture). It was observed that the developed inductors with the number of turns of 7 have the inductance of 33 to 100nH and exhibit the self-resonant frequency (SRF) of .26 to 1.1 GHz. The SRF of inductors decreases with increasing the inductance and the inductors have the quality factor of 60 to 80 in the frequency range of 300 MHz to 1.1 GHz. In this study, small-size solenoid-type RF chip inductors with high inductance and high quality factor were fabricated successfully. It is suggested that the thin film-type inductor is necessary to fabricate the smaller size inductors at the expence of inductance and quality factor values.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.2
• /
• pp.164-172
• /
• 2014

This paper presents an analysis of a leakage inductance for a toroidal type flyback transformer. The equation to calculate the leakage inductance is derived using the MMF diagram of the transformer. The analysis for the different types of the cores and winding structures is also provided using the FEM simulation. The winding structures minimizing the leakage inductance are finally discussed from the simulation and experimental results.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.893_894
• /
• 2009

This paper study on the notch effect for d-q axis inductance of interior type permanent magnet (IPM) motor. The variations of d-q axis inductance are analyzed by finite element method (FEM). Applying the notch for cogging torque minimization and maximization of reluctance torque is confirmed to be improve the torque characteristics. Also, speed characteristics is analyzed according to the load current

• 한국초전도학회:학술대회논문집
• /
• v.15
• /
• pp.96-96
• /
• 2005

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.844_845
• /
• 2009

Inductance and back EMF are important parameters in characteristic analysis of brushless motor. Inductance is constant value in surface permanent magnet type brushless motor. But it is change depending on the position of the rotor in interior permanent magnet type brushless motor. So this paper is considering for change inductance in characteristic analysis of brushless motor. Characteristic analysis is executed by the method that three-phase bipolar 120 degree commutation drive type.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.53 no.1
• /
• pp.13-21
• /
• 2004

In the design of superconducting cable systems, quench analysis have to be advanced for applying to a real systems. It is necessary to calculate the current, voltage and resistance during the quench. Simulation program named EMTDC was used to analyze the quench state. Normal zone evaluation and quench development with EMTDC are one of the major features of quench analysis. This paper presents the two kinds of quench control models which are the Switch Control Type and the Fortran Control Type. In case of the quench developing area, the simplicity cable model consist of resistance, inductance and capacitance. The impedance of the pipe type superconducting cable is calculated by numerical analysis method. The resistance and inductance increased during quench. However the variation have an effect on the fault current. The voltage was also developed by resistance and inductance. This paper presents the relationship between the current. voltage, resistance and inductance during quench.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.11 no.4
• /
• pp.19-24
• /
• 1974

An ungrounded inductance, necessary for construction of general type networks, is synthesized using two operational amplifiers and several passive elements. Through indefinite admittance matrix procedure. it is proved that the synthesized network is equivalent to an ungrounded pure inductance with a positive and a negative resistance in the parallel arms. A practical low-pass filter is made according to this synthesis method, and the resultant characteristic has been verified by means of IBM's simulation program ECAP (Electronic Circuit Analysis Program).