• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.8
• /
• pp.591-596
• /
• 2013

Indium Zinc Tin Oxide (IZTO) thin films were developed as an alternative to Indium Tin Oxide (ITO) thin films. ITO material which has been acknowledged with its low resistivity and optical transparency of 85-90% has been used as major transparent conducting oxide (TCO) materials. However, due to the limited source, high price, and instability problems at high temperature of indium, many researches has been focused on indium-saving TCO materials. Mason Group of Northwestern University was reported to expand the solubility limit up to 40% by co-doping with 1:1 ratio of $Zn^{+2}$ and $Sn^{+4}$ ions. In this study, the properties of IZTO thin films corresponding to Zn/Sn different ratio were investigated. In addition, the effect of substrate temperature variable to the structural, optical and electrical properties of IZTO thin films was investigated.

• Applied Chemistry for Engineering
• /
• v.17 no.6
• /
• pp.644-647
• /
• 2006

The indium zinc oxide (IZO) thin films were deposited using a radio frequency reactive magnetron sputtering method. Among the various processing variables, $O_{2}$ concentration and annealing temperature after deposition were selected and the optical, electrical, and structural properties of IZO thin films were investigated. As the $O_{2}$ concentration increased, the deposition rate of IZO thin films decreased, the resistivity increased and the transmittance slightly increased. According to atomic force microscopy analysis, the IZO films deposited at pure Ar showed rough surface and those deposited with $O_{2}$ addition exhibited relatively smooth surface. The IZO thin films deposited at pure Ar were annealed at 250, 350, and $450^{\circ}C$, respectively. The IZO thin film deposited at pure Ar showed the lowest transmittance and resistivity and resistivity greatly increased at the annealing temperature exceeding $250^{\circ}C$. The higher annealing temperature IZO films were annealed at, the smoother surface the films showed. The x-ray diffraction revealed that IZO films annealed at higher temperature had better crystalline structures.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.522-525
• /
• 2004

ITO thin films $({\sim}150\;nm)$ are deposited on glass substrates by different deposition condition. The sheet resistance of ITO thin films measured by using a four probe station. The microstructure of these films is determined using a X-ray diffractometer (XRD) and a scanning electron microscope (SEM) and a atomic force microscope (AFM). The sheet resistance of ITO thin films compared $s_{11}$ values by using a near field scanning microwave microscope.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.1042-1045
• /
• 2004

ITO thin films ($\sim150nm$) are deposited on glass substrates by different deposition condition. The sheet resistance of ITO thin films measured by using a four probe station. The microstructure of these films is determined using a X-ray diffractometer (XRD) and a scanning electron microscope (SEM) and a atomic force microscope (AEM). The sheet resistance of ITO thin films compared $s_11$ values by using a near field scanning microwave microscope.

• New & Renewable Energy
• /
• v.17 no.1
• /
• pp.1-6
• /
• 2021

Transparent conducting oxide (TCO) films have been widely used in optoelectronic devices, such as OLEDs, TFTs, and solar cells. However, thin films of indium tin oxide (ITO) have few disadvantages pertaining to process parameters such as substrate temperature and sputtering power. In this study, we investigated the requirements for using TCO films in silicon-based solar cells and the best alternative TCO materials to improve their efficiency. Moreover, we discussed the current status of high-efficiency solar cells using low-temperature TCO films such as indium zinc oxide and Zr-doped indium oxide.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.98-98
• /
• 1999

Highly transparent and conducting tin-doped indium oxide (ITO) films were deposited on polycarbonate substrate by ion-assited deposition. Low substrate temperature (<10$0^{\circ}C$) was maintained during deposition to prevent the polycarbonate substrate from be deformed. The influence of ion beam energy, ion current density, and tin doping, on the structural, electrical and optical properties of deposited films was investigated. Indium oxide and tin-doped indium oxide (9 wt% SnO2) sources were evaporated with assisting ionized oxygen in high vacuum chamber at a pressure of 2$\times$10-5 torr and deposition temperature was varied from room temperature to 10$0^{\circ}C$. Oxygen gas was ionized and accelerated by cold hallow-cathode type ion gun at oxygen flow rate of 1 sccm(ml/min). Ion bea potential and ion current of oxygen ions was changed from 0 to 700 V and from 0.54 to 1.62 $\mu$A. The change of microstructure of deposited films was examined by XRD and SEM. The electrical resistivity and optical transmittance were measured by four-point porbe and conventional spectrophotometer. From the results of spectrophotometer, both the refractive index and the extinction coefficient were derived.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.2
• /
• pp.59-62
• /
• 2013

At an infra-red (IR) wavelength of 1,064 nm, a diode-pumped Q-switched $Nd:YVO_4$ laser was used for the direct patterning of various transparent conductive oxide (TCO) thin films on glass substrate. With various laser beam conditions, the laser ablation results showed that the indium tin oxide (ITO) film was removed completely. In contrast, zinc oxide (ZnO) film was not etched for any laser beam conditions and indium gallium zinc oxide (IGZO) was only ablated with a low scanning speed. The difference in laser ablation is thought to be due to the crystal structures and the coefficient of thermal expansion (CTE) of ITO, IGZO, and ZnO. The width of the laser-patterned grooves was dependent on the film materials, the repetition rate, and the scanning speed of the laser beam.

• ETRI Journal
• /
• v.27 no.4
• /
• pp.405-410
• /
• 2005

High quality indium tin oxide (ITO) thin films were grown by pulse laser deposition (PLD) on flexible polyethersulphone (PES) substrates. The electrical, optical, and surface morphological properties of these films were examined as a function of substrate temperature and oxygen pressure. ITO thin films, deposited by PLD on a PES substrate at room temperature and an oxygen pressure of 15 mTorr, have a low electrical resistivity of $2.9{\times}10^{-4}{\Omega}cm$ and a high optical transmittance of 84 % in the visible range. They were used as the anode in organic light-emitting diodes (OLEDs). The maximum electro luminescence (EL) and current density at 100 $cd/m^2$ were 2500 $cd/m^{2}$ and 2 $mA/m^{2}$, respectively, and the external quantum efficiency of the OLEDs was found to be 2.0 %.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.11
• /
• pp.2016-2020
• /
• 2010

Indium-zinc-oxide (IZO) films were deposited at room temperature via RF sputtering with varying the flow rate of additive nitrogen gas ($N_2$). Thin film transistors (TFTs) with an inverted staggered configuration were fabricated by employing the various IZO films, such as $N_2$-added and pure (i.e., w/o $N_2$-added), as active channel layers. For all the deposited IZO films, effects of additive $N_2$ gas on their deposition rates, electrical resistivities, optical transmittances and bandgaps, and chemical structures were extensively investigated. Transfer characteristics of the IZO-based TFTs were measured and characterized in terms of the flow rate of additive $N_2$ gas. The experimental results indicated that the transistor action occurred when the $N_2$-added (with $N_2$ flow rate of 0.4-1.0 sccm) IZO films were used as the active layer, in contrast to the case of using the pure IZO film.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.18 no.4
• /
• pp.160-164
• /
• 2008

Insulating and conducting 12CaO ${\cdot}7Al_2O_3$ (Cl2A7)-doped indium tin oxide (ITO) (ITO:Cl2A7 insulator and electride) thin films were deposited on glass substrates by an RF magnetron co-sputtering method with increasing number of insulating and conducting Cl2A7 target chips. The structural, electrical and optical properties of these films were investigated. The carrier concentration decreased and resistivity increased in the films with increasing number of Cl2A7 target chips. The optical transmittance of all of the thin films was above 80 % in the visible wavelength range. The structural property and surface roughness of the films were examined and the decrease of crystallinity and surface roughness was strongly dependent on the change of grain size.