• 한국재료학회지
• /
• 제7권2호
• /
• pp.162-170
• /
• 1997

This study has evaluated the dissimialr weldability of Incoloy 825 Ni base alloy with a mild steel(SS41). Further a compatibility study of wrveral Ni base filler metals with the dissimilar joint between the two alloys was also included. The dissimilar weldability of Incoloy 825 with mild steel is strongly dependent upon the type of the filler metal used. Among the filler metals, ENiCrFe which has a chemical comosition similar to that of Incoloy 825 was found to be most compatible to the joint. In addition, a filler metal which showed a good cracing resistance in one dissimiar alloy combination was not necessarily graranteed to other combination. Microstructural examination with SEM, TEM and Auger revealed that the solidification cracking resestance of the dissimilar joint. between Incoloy 835 and SS41 was closely with the Ti+Nb content and with the content of a low melting eutectic phase of Laves relatibve to that of MC type phase.

• 열처리공학회지
• /
• 제30권3호
• /
• pp.99-105
• /
• 2017

This study was carried out to investigate the effect of heat treatment on the microstructure and mechanical properties in 90% hot forged Incoloy 825 alloy. With increasing solution treatment temperature, the grain size increased and the volume fraction of total precipitates decreased, and the precipitates disappeared at $1,000^{\circ}C$. With increasing aging time at $700^{\circ}C$, the volume fraction of precipitate increased and the precipitates size increased. Most of the precipitates consist $Cr_{23}C_6$ carbide, and a small amount of TiC carbide was also observed. With decreasing solution treatment temperature and increasing aging time, tensile strength and hardness increased, and the elongation and impact value decreased. With increasing aging time, the impact value decreased sharply by the increased of the precipitate size.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1994년도 특별강연 및 춘계학술발표 개요집
• /
• pp.113-114
• /
• 1994

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권6호
• /
• pp.698-703
• /
• 2014

최근 기존 화석연료의 고갈로 인하여 대체에너지로써 천연액화가스의 수요 증가와 함께 LNG 운반선의 수요가 증가하고 있으며, 그로인해 극한의 환경에서 사용할 수 있는 LNG 선박용 벨로우즈의 수요 또한 증가할 것으로 예상된다. 현재 LNG 선박용 벨로우즈에 사용되는 재료는 저온취성과 해수부식에 강한 INCOLOY 825와 STS316L합금이다. 본 연구에서는 극저온에 사용되는 LNG용 벨로우즈 재질인 INCOLOY 825과 STS316L 합금에 대하여 최적의 용접조건을 설정하고, 에릭센 시험을 통하여 용접부의 성형성을 분석하였다. 최적 조건에서의 용접시 용접부의 인장강도는 모재에 비하여 90% 이상의 강도값을 나타내었다. 또한 에릭센 시험을 통한 성형성 분석의 결과, 용접부가 아닌 모재에서 파단이 발생하는 매우 양호한 용접부를 얻을 수 있었다.

• 열처리공학회지
• /
• 제29권6호
• /
• pp.259-263
• /
• 2016

This study was carried out to investigate the effect of hot forging ratio on the microstructure and mechanical properties of incoloy 825 alloy. Hot forging was carried out at the forging ratio of 0%, 60% and 90% respectively in a range of $900^{\circ}C{\sim}1,140^{\circ}C$ and followed solution treatment was conducted at $1,000^{\circ}C$ for 1 hr. In all the specimens of hot forged of 0%, 60% and 90%, precipitates were not observed. The average grain size of 0% specimen is $82{\mu}m$ and that of 60% and 90% is $56{\mu}m$ and $31{\mu}m$, respectively. The range of grain size in the 0% specimen is uneven in $182{\mu}m$ to $31{\mu}m$, but the grain size of 90% specimen is uniform. With increasing hot forging ratio, the mechanical properties such as tensile strength, elongation, hardness increased and impact toughness increased by grain refinement.

• 동력기계공학회지
• /
• 제21권2호
• /
• pp.20-26
• /
• 2017

This study was carried out to investigate the effect of precipitate on the high temperature deformation stability of incoloy 825 alloy. $Cr_{23}C_6$ carbide was precipitated under $950^{\circ}C$, but was not detected over $1,000^{\circ}C$. Most of the precipitation consist of $Cr_{23}C_6$ carbide. Strain-rate sensitivity was the highest in 0.01/s and the lowest in 10/s. Strain-rate sensitivity was decreased sharply below $950^{\circ}C$. In the temperature between $850^{\circ}C{\sim}1,150^{\circ}C$, plastic instable area did not exist. It showed the lowest Ziegler Parameter value of 0.06 Ziegler Parameter was the lowest as 0.06 at $850^{\circ}C$ with 10s-1 of strain. The highest Ziegler Parameter value(0.43) was found in plastic deformation at $1,050^{\circ}C$ with 0.01s-1 of strain. It tends to have an higher resistance to the high temperature deformation under $950^{\circ}C$, due to the precipitation.

• 열처리공학회지
• /
• 제31권5호
• /
• pp.213-219
• /
• 2018

This study was carried out to investigate the effect of hot forging ratio and solution treatment temperature on the mechanical properties of incoloy 825 alloy. With an increasing of the hot forging ratio, grain size and range of grain size was decreased. With an increasing of the solution treatment temperature after 90% forging, grain size and range of grain size was increased. Cr carbides and Ti nitrides was precipitated at below $900^{\circ}C$ and volume fraction of precipitate was increased with an decreasing of the solution treatment temperature. With an increasing of the hot forging ratio, hardness, tensile strength and elongation, toughness was increased. With an increasing of the solution treatment temperature after 90% forging, hardness and strength was increased, elongation and toughness was decreased by grain refinement. With an increasing of the forging ratio, effect of solution treatment temperature on the hardness, strength and elongation was small, but on the toughness was large.

• 한국산업융합학회 논문집
• /
• 제24권3호
• /
• pp.261-269
• /
• 2021

This study was evaluated the elastic wave properties according to tension of Incoloy 825 alloy with different solution treatment temperature and aging time. Solution treatment was carried out at 700, 800, 900, and 1000 ℃ for 1 hour, and aging was carried out at 700 ℃ for 1, 5, 10, and 30 hours. As the solution treatment temperature increased, the tensile strength decreased and the elongation increased. However, as the aging time increased, the tensile strength increased and the elongation decreased. The dominant frequency decreased as the solution treatment temperature increased, but increased as the aging time increased. The dominant frequency according to the solution treatment and aging time increased as the tensile strength increased, but increased despite the decrease in elongation.

• Journal of Welding and Joining
• /
• 제13권3호
• /
• pp.147-156
• /
• 1995

The change of microstructure in the bonded interlayer and tensile properties of joints were studied for liquid phase diffusion bonding using STS-310 and Incoloy-825 as base metal and base metal+B alloy as insert inetal. Main experimental results obtained in this study are as follows. 1) The optimum amount of B addition into the insert metal was found to be about 4mass%. 2) When isothermal solidification was completed, the microstructure in the bonded interlayer was the same with that of the base metal because of the grain boundary migration in the bonded interlayer. 3) All of the tensile specimen fractured at base metal and joints bonded at optimum condition exhibited tensile properties in excess of base metal requirements. 4) It was determined that fine car-borides and bordes such as M$_{23}$(C,B)$_{6}$, Cr$_{2}$B, and CrB in STS-310S and TiB in Incoloy-825 exist at the grain boundary around bonded interlayer. These precipitates almost disappeared after homogenizing treatment at 1373K for 86.4ks.s.

• Journal of Welding and Joining
• /
• 제15권5호
• /
• pp.46-55
• /
• 1997

This study has evaluated the liquation cracking behavior in the heat affected zone of several Ni base superalloys (Incoloy 825, Inconel 718 and Inconel 600). 304 and 310S austenitic stainless steels were also included for comparison. In addition, the mechanism of liquation cracking in the HAZ was postulated based on the extensive microstructural examinations with SEM, EDAX and TEM. The liquation cracking resistance of Ni base alloys was found to be far inferior to that of austenitic stainless steels. The liquation cracking of Incoloy 825 and Inconel 718 was believed to be closely related with the Laves-austenite(Ti rich in 825 and Nb rich in 718) and MC-austenitic eutectic phases formed along the grain boundaries by constitutional liquation and incipient melting under rapid welding thermal contraction. Further, liquation cracking resistance of the HAZ was dependent not only upon the type and amount of low melting phases but also on the grain size.