• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.3
• /
• pp.111-117
• /
• 2014

With the development of technology, the display industry has been focusing on the development of new types of displays, such as bendable and wearable displays. However, the PVA/TAC polarizing film used in the manufacturing of a normal display is associated with low luminance and low efficiency. If the existing polarization film is replaced with a wire grid polarizer, it is possible to reduce the thickness significantly. Moreover enhanced brightness can also be expected. This study confirms the optical properties of the WGP through a simulation.

• Proceedings of the Optical Society of Korea Conference
• /
• 2000.02a
• /
• pp.146-147
• /
• 2000

The electromagnetic wave scattering from active objects has only recently attracted attention.$^{(1).(3)}$ Theoretical studies have considered normal-incidence plane-wave interactions with active dielectric cylinders with the prediction of large enhancements in the scattered field for bound mode structures. According to the theory of the electromagnetic wave scattering from a dielectric cylinder, the eigenvector solutions are discrete and have both guided (non-radiative) and leaky (radiative) mode solutions. By using an anti-guiding (leaky) structure instead of a guided structure and scattering at oblique incident angles near critical angle, the scattering resonances predicted by theoretical studies were obtained for the first time. A fine-grained scan of the plane-wave incident angle a reveals the existence of discrete scattering resonances. The diameter and real part of the index of refraction determine the resonant conditions and the imaginary part of the refractive index has a threshold value to make mode up for its radiation loss. The cross coupling between transverse electric (TE) and transverse magnetic (TM) modes is clearly detected for both active and passive scattering as theoretically expected. (omitted)

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.4
• /
• pp.1051-1058
• /
• 1998

We propose a bandpass filter using wavelength selectivity as variation of writing beam incident angle in photorefractive crystal. From TWM(Two-Wave Mixing) experiment, optimal diffraction properties are induced, and bandpass filter for selection wavelength transmission bandwidth are taken by change of writing beam incident angle.

• KIEAE Journal
• /
• v.5 no.3
• /
• pp.33-40
• /
• 2005

The existing building code regulates the minimum distance between buildings and the minimum required sunshine hours for winter solstice to ensure the right to light. Especially, the minimum sunshine hours have been guaranteed by the constitution after the right for the people to live in a healthy and comfortable environment was established. However, the existing regulation on the sunshine hours only considers the duration of sunshine hours, but ignores the minimum amount of sunlight. Therefore, the calculated sunshine hours are not coincident with the hours occupants actually feel. Therefore, the purpose of this study is to investigate the effect of solar incident angle on interior illuminance distribution, which will be used to propose a new code on the minimum sunshine hours and levels.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.395-398
• /
• 2000

Reactive radio frequency (RF)magnetron sputter with incident angle has been used to deposit AlN thin film on a crystalline Si substrate. (002)Preferred orientation of AlN thin film has been obtained at low sputtering pressure. Also it has been shown that depostion rate of AIN thin film is affected by fraction Ar and $N_2$ partial pressure. But substrate temperature didn't affect depostion rate of AIN thin film . As sputtering pressure increased preferred orientation degraded. The internal stress changed from tensile stress to compressive stress as fraction of $N_2$ partial pressure increased. At low nitrogen partial pressure cermet$^{[1]}$ AIN thin film is obtained.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.6
• /
• pp.96-101
• /
• 2020

In this paper, we present the results of our research to perform 3D laser scanning functions by adding a focusing lens to a conventional 2D laser scanner. For the optical design, the ray-tracing technique was used along with a total of four lenses as the variable incident focusing lens, the collimating lens, and the F-Theta lens. As design variables, the curvature of the incident focusing lens (Lens #1) was assumed to be us, l mm and sumed mm, and the incident angles were set at 0cidenus, l. In addition, the distance between the focusing lens and the collimating lens was set to vary from 5 mm to 15 mm. When the incident focal length was varied from 5 mm to 15 mm, the exit focal length was calculated to vary from 67.5 mm to 56.8 mm for the lens with R = 100 mm and from 108.5 mm to 99.0 mm for the lens with R = 150 mm. When the incident angle was 0°, the focal aberration was only slightly observable at 10㎛ in both the x- and y-direction. At 7.5° was the focal aberration of approximately 20~50㎛ was measured at 20㎛. To investigate the chromatic aberration of the designed optical device, the distortion of the focus was observed when the 550 nm beam was simulated on lens designed for a 980 nm wavelength.

• Wind and Structures
• /
• v.5 no.1
• /
• pp.25-48
• /
• 2002

Wind flow and pressure on the roof of the Texas Tech Experimental Building are studied along with the incident wind in an effort to understand the wind-structure interaction and the mechanisms of roof pressure generation. Two distinct flow phenomena, cornering vortices and separation bubble, are investigated. It is found for the cornering vortices that the incident wind angle that favors formation of strong vortices is bounded in a range of approximately 50 degrees symmetrical about the roof-corner bisector. Peak pressures on the roof corner are produced by wind gusts approaching at wind angles conducive to strong vortex formation. A simple analytical model is established to predict fluctuating pressure coefficients on the leading roof corner from the knowledge of the mean pressure coefficients and the incident wind. For the separation bubble situation, the mean structure of the separation bubble is established. The role of incident wind turbulence in pressure-generation mechanisms for the two flow phenomena is better understood.

• Proceedings of the Optical Society of Korea Conference
• /
• 2004.07a
• /
• pp.52-53
• /
• 2004

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.147-151
• /
• 1999

YBCO step-edge Josephson junction were fabricated on sapphire substrates. The steps were formed on R-plane sapphire substrates by using Ar ion milling with PR masks. The step angle was controlled in the wide range from 25$^{\circ}$ to 50$^{\circ}$ by adjusting both the Ar ion incident angle and the photoresist mask rotation angle relative to the incident Ar ion beam. CeO$_2$ buffer layer and in-situ YBa$_2Cu_3O_{7-{\delta}}$ (YBCO) thin films was deposited on the stepped R-plane sapphire substrates by pulsed laser deposition method. The YBCO film thickness was varied to obtain the ratio of film thickness to step height in the range from 0.5 to 1. The step edge junction exhibited RSJ-like behaviors with I$_cR_n$ product of 100 ${\sim}$ 300 ${\mu}$V, critical current density of 10$^3$ ${\sim}$ 10$^5$ A/ cm$^2$ at 77 K.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.1
• /
• pp.78-86
• /
• 2001

The Gasoline Direct Injection(GDI) system has been highlighted due to the improvement of fuel consumption and the control of exhaust emission from gasoline engines. The GDI system includes a high injection pressure, smaller mean diameter, good spray characteristics and stability. We were interested in the development for gasoline direct swirl injector(GDSI) in which the swirler is specially designed with an incident angle. Nymerical analysis was utilized to investigate the internal flow of GDSI with a goal to determine the swirl incident angle and needle lift. Accordingly, it describes characteristics of a GDSI in which the flowrate and spray characteristics are satisfied. especially the spray tip penetration decreases, compared with other type GDI, mean diameter of droplets is from 20${\mu}{\textrm}{m}$ to 25${\mu}{\textrm}{m}$ and spray angle ranges from 64$^{\circ}$to 66$^{\circ}$.