• Journal of Korean Tunnelling and Underground Space Association
• /
• v.5 no.1
• /
• pp.43-54
• /
• 2003

In the deign of cut and cover tunnel, the structural analysis such as rigid frame analysis has been used for its simplicity and convenience. The structural analysis, however, can not consider the geological and geotechnical factors such as soil arching effect. In this study, the dominant factors influencing the behavior of cut and cover tunnel such as interface element, slope of excavation plane, distance between slope and tunnel lining, and location of slope of covered soil, were investigated by the numerical analysis to develop the analysis technique and design technology. Based on the results, the variation of bending moment, shear stress, axial force and displacements were evaluated and analyzed for each factor.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2013.05a
• /
• pp.15-16
• /
• 2013

Magnetization behavior of ultra thin $Fe_xCo_{1-x}$ alloy (where x varies from 0 to 100) has been investigated as functions of composition on Cr (100) substrate by using in situ surface magneto optical Kerr effect (SMOKE). It's always show in plane uniaxial magnetic anisotropy at room temperature (RT) & Low temperature (LT). It is observed that composition dependent coercive force maximum at about 30 at % Co and 70 at % Co atomic ratio and minimum near equiatomic site. The relative magnetic moments as composition variation also show magnetization collapse near equiatomic site. The magnetization behaviors of Fe-Co alloy on Cr (100) due to composition varies are supported the order-disordering as well as structural stability bcc (ferromagnetic)/fcc (anti-ferromagnetic) phase stability magnetism.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.3 no.4
• /
• pp.256-262
• /
• 1991

The corrosion effects on thermal contact resistance were experimentally studied for a given contact interface of a couple of metals. 2 cylindrically shaped test pieces, the one was carbon steel whose surface was machined by lathe and the other was stainless steel, ground, were come into contact under pressure, and then submerged to $HNO_3$ gas environment. While the corrosion process was going on, the thermal contact resistance was measured with time. The experiment was performed for 2 cases; 1) Highly compress the test pieces and then bring them to $HNO_3$ gas environment. 2) Anteriorly corrode the interface under low contact pressure and then increase the contact pressure. The results were as follows; In 1st. case of experiment, the thermal contact resistance seemed to be very stable, and showed low values with a tendancy of small decrease with time. But in 2nd. case the resistance was unstable and jumped to a value of 200-250% more then that expected for uncontaminated interface. More over it demonstrated some increase with time.

• Journal of Korean Society of Steel Construction
• /
• v.23 no.4
• /
• pp.455-464
• /
• 2011

In this study, the buckling analysis of the vertically curved stiffened web plate was conducted through finite-element analysis, using an eight- and nine-node flat shell element with a substitute shear strain field. To investigate the buckling behavior of the vertically curved web plate with a longitudinal or vertical stiffener under in-plane moment loading, parametric studies were conducted for the variation of the width (b) and ratio of the bending stiffness of the stiffener to that of the plate (${\gamma}=EI/bD$). The static behavior of the vertically curved web plate without a stiffener was also investigated, and then the buckling abilities of the longitudinal and vertical stiffeners were compared under moment loading.

• Tunnel and Underground Space
• /
• v.33 no.3
• /
• pp.150-168
• /
• 2023

The anisotropic behavior of rocks is primarily attributed to the directional arrangement of rock-forming minerals and the distribution characteristics of microcracks. Notably, sedimentary and metamorphic rocks often exhibit distinct transverse isotropy in terms of their strength and deformation characteristics. Consequently, it is crucial to gain accurate insights into the deformation and failure characteristics of transversely isotropic rocks during rock mechanics design processes. The deformation of such rocks is described by five independent elastic constants, which are determined through laboratory testing. In this study, the characteristics of the directional variation of apparent elastic constants in transversely isotropic rocks were investigated using experimental data reported in the literature. To achieve this, the constitutive equation proposed by Mehrabadi & Cowin was introduced to calculate the apparent elastic constants more efficiently and systematically in a rotated Cartesian coordinate system. Four transversely isotropic rock types from the literature were selected, and the influence of changes in the orientation of the weak plane on the variations of the apparent elastic modulus, apparent shear modulus, and apparent Poisson's ratio was analyzed. Based on the investigation, a new constraint on the elastic constants has been proposed. If the proposed constraint is satisfied, the directional variation of the apparent elastic constants in transversely isotropic rocks aligns with intuitive predictions of their tendencies.

• Progress in Medical Physics
• /
• v.27 no.1
• /
• pp.1-7
• /
• 2016

In this work, we considered a compressed-sensing (CS)-based image deblurring scheme with a total-variation (TV) regularization penalty for improving image characteristics in digital tomosynthesis (DTS). We implemented the proposed image deblurring algorithm and performed a systematic simulation to demonstrate its viability. We also performed an experiment by using a table-top setup which consists of an x-ray tube operated at $90kV_p$, 6 mAs and a CMOS-type flat-panel detector having a $198-{\mu}m$ pixel resolution. In the both simulation and experiment, 51 projection images were taken with a tomographic angle range of ${\theta}=60^{\circ}$ and an angle step of ${\Delta}{\theta}=1.2^{\circ}$ and then deblurred by using the proposed deblurring algorithm before performing the common filtered-backprojection (FBP)-based DTS reconstruction. According to our results, the image sharpness of the recovered x-ray images and the reconstructed DTS images were significantly improved and the cross-plane spatial resolution in DTS was also improved by a factor of about 1.4. Thus the proposed deblurring scheme appears to be effective for the blurring problems in both conventional radiography and DTS and is applicable to improve the present image characteristics.

• The korean journal of orthodontics
• /
• v.17 no.2
• /
• pp.311-320
• /
• 1987

The purpose of this study was to investigate the growth changes of maxilla and mandible and position changes of first permanent molars of growing children The author analyzed the data using cephalometric roentgenogram of 43 boys and 39 girls age of 6 to 11 with normal occlusion The obtained results were as follows 1 The eruption path of maxillary and mandibular first permanent molar superimposed on TM-ANS and mandibular plane shows individual variation 2 There was no correlation between horizontal and vertical changes of maxillary first permanent molar, but positive correlation in mandibular first permanent molar 3 As the eruption, the forward changes of mandibular first permanent molar was significantly greater than that of maxillary first permanent molar 4 As the ages were increased, there were irregular growth changes of maxilla and mandible 5 Growth changes of lower anterior facial height was relatively stable 6 N-S-${\bar{6}}$ was stable after age 7.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.285-288
• /
• 2008

The Present Study describes the numerical investigations concerning a fuel(Hydrogen), inert gas (Nitrogen) or supersonic air stream issued between each other. The basic flow configuration consists of a plane, double shear/mixing layer flow. For the numerical solution, a fully conservative unsteady $2^{nd}$ order time accurate sub-iteration method and a $2^{nd}$ order Total Variation Diminishing(TVD) scheme are used with the finite volume method(FVM). The results are consist of three categories ; single shear layer consist of fuel and supersonic air stream, inert gas stream issued between supersonic air and fuel stream, fuel gas stream issued between supersonic air and fuel stream. The numerical calculations has been carried out in case of 1,2, and 4mm thickness of center stream. The width of total gas stream is 4cm.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.2 no.2
• /
• pp.13-19
• /
• 2011

This paper presents the stress distribution of the damaged butt joint of steel plate using CFRP laminates when the flange in tension zone of steel box girder is welded by butt welding. When CFRP sheets are patched on tension flange of steel-box girder, the stress distribution of a vertical and normal direction on damaged welding part is shown as parameters such as a variation of the thickness of adhesive, the overlap length with steel, and the modulus of elasticity of CFRP sheets. For the study, we wrote the computer program using the EAS(Enhanced assumed strain) finite element method for plane strain that has a very fast convergency and exact stress for distorted shape.

• Korean Journal of Optics and Photonics
• /
• v.7 no.2
• /
• pp.174-180
• /
• 1996

For the investigation of the influence of microstructure of optical thin films on the in-plane thermal diffusivity of glass substrate coated by that films, we constructed the AC calorimeter which uses argon-ion laser as a thermal source and measured several kinds of ZnS optical thin films which prepared by the changing of thermal evaporation speed such as 5$\AA$/s, 10$\AA$/s, 20$\AA$/s, 40$\AA$/s, 60$\AA$/s. The result showed that the thermal diffusivity decreases as the temperature increases. Also, when the evaporation speed is 20$\AA$/s, the thermal diffusivity has maximum value, and the variation of the thermal diffusivities are 27% at maximum.