• Journal of Power Electronics
• /
• 제17권3호
• /
• pp.756-765
• /
• 2017

The control of the power conversion system (PCS) in a battery energy storage system has a challenge due to the existence of grid impedance. This paper studies an impedance model of an LCL-based PCS in the d-q domain. The feature of a PCS connected to a weak grid is unveiled by use of an impedance model and a generalized Nyquist criterion. It is shown that the interaction between grid impedance and the PCS destabilizes the cascaded system in certain cases. Therefore, this paper proposes a novel control method that adopts virtual resistors to overcome this issue. The improvement in the control loop leads the PCS to a more stable condition than the conventional method. Impedance measurement is implemented to verify the correctness of the theoretical analysis. Experimental results obtained from a down-scaled prototype indicate that the proposed control method can improve the performance of the PCS under a weak grid.

• 대한조선학회논문집
• /
• 제50권2호
• /
• pp.79-87
• /
• 2013

In this paper, an Euler equation solver based on a Cartesian-grid method and non-uniform staggered grid system is applied to predict the ship motion response and added resistance in waves. Water, air, and solid domains are identified by a volume-fraction function for each phase and in each cell. For capturing the interface between air and water, the tangent of hyperbola for interface capturing (THINC) scheme is used with a weighed line interface calculation (WLIC) method. The volume fraction of solid body embedded in a Cartesian-grid system is calculated by a level-set based algorithm, and the body boundary condition is imposed by volume weighted formula. Added resistance is calculated by direct pressure integration on the ship surface. Numerical simulations for a Wigley III hull and an S175 containership in regular waves have been carried out to validate the newly developed code, and the ship motion responses and added resistances are compared with experimental data. For S175 containership, grid convergence test has been conducted to investigate the sensitivity of grid spacing on the motion responses and added resistances.

• 한국ITS학회 논문지
• /
• 제9권1호
• /
• pp.76-90
• /
• 2010

고정 인프라 없이 차량 노드 간 자체적으로 구성되는 차량 애드?혹 네트워크, VANET은 사고 예방과 교통량 통제로 그 사용 목적과 필요성이 분명하게 나타난다. VANET 환경에 적합한 위치 정보 기반 라우팅 기법은 소스 노드가 목적지 노드의 위치 정보를 가지고 있다는 전제를 바탕으로 하여, 위치 정보 제공을 위한 위치 정보 서비스(Location service)가 요구된다. 본 논문에서는 위치 정보 서비스에서의 접근성 문제 및 노드 간 형평성 유지에 관한 문제를 해결하기 위해 최적경로 설정을 위한 그리드 기반 위치 정보 서비스 스팟(Grid-based Location service spot, GLSS) 기법을 제안한다. 이 기법에서 지역을 구성하는 각 그리드에 일정 범위가 LSS로 설정되어, 해당 그리드의 모든 노드들은 위치 정보 등록 및 요청 메시지를 LSS로 Geocast 전송을 하게 된다. 위치 정보 요청 메지시는 LSS 간 확산을 통해 응답 메시지 발신 노드는 그리드 간 최적 경로를 통해 전달을 수행하여 신뢰성 있는 전송을 보장한다. 본 논문에서는 도로 환경과 지형 지물을 고려하여 각 그리드의 LSS를 경유하는 최적 경로 기법과 GPSR을 비교하여 성능 평가를 수행하였다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2006년도 제33회 KOSCO SYMPOSIUM 논문집
• /
• pp.145-150
• /
• 2006

At the furnace top, the distribution of charging coke and ore is adjusted to control the reducing gas flow distribution in the furnace. It is necessary to predict operation condition of blast furnace according to the burden profile to judge whether charging is properly conducted In this study, We propose the model for predicting while layer structures whithin furnace when top burden profile was given. Layer structure of coke and ore could be predicted by top burden profile and solid velocity. Solid velocity is assumed as potential flow. Potential function distribution and timeline are also calculated using solid velocity field. The Calculation is conducted for different burden profile cases. As the result burden distribution and grid structure, which is deformed to match the layer structure in shaft and deadman profile. Gas flow was calculated using this grid, and calculated results are compared with each other.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제4권2호
• /
• pp.100-105
• /
• 2004

The influencing factors on the OPC (optical proximity correction) results are quantitatively analyzed using OPCed L/S patterns. ${\sigma}$ values of proximity variations are measured to be 9.3 nm and 15.2 nm for PR-A and PR-B, respectively. The effect of post exposure bake condition is assessed. 16.2 nm and 13.8 nm of variations are observed. Proximity variations of 11.6 nm and 15.2 nm are measured by changing the illumination condition. In order not to seriously deteriorate the OPC, these factors should be fixed after the OPC rules are extracted. Proximity variations of 11.4, 13.9, and 15.2 nm are observed for the mask mean-to-targets of 0, 2 and 4 nm, respectively. The decrease the OPC grid size from 1 nm to 0.5 nm enhances the correction resolution and the OCV is reduced from 14.6 nm to 11.4 nm. The enhancement amount of proximity variations are 9.2 nm corresponding to 39% improvement. The critical dimension (CD) uniformity improvement for adopting the small grid size is confirmed by measuring the CD uniformity on real SRAM pattern. CD uniformities are measured 9.9 nm and 8.7 nm for grid size of 1 nm and 0.5 nm, respectively. 22% improvement of the CD uniformity is achieved. The decrease of OPC grid size is shown to improve not only the proximity correction, but also the uniformity.

• Journal of Electrical Engineering and Technology
• /
• 제13권5호
• /
• pp.2050-2058
• /
• 2018

Impulse characteristic of transmission tower grounding grid is needed for lightning protection of transmission line. This paper describes an outdoor experimental test facility established for large-scale grounding grid of transmission tower, made up of four impulse current generators and a circle current return electrode. The amplitude of impulse current is up to 100 kA. The results of the CDEGS simulation and GPR measurement reveal the uniform current distribution in the test arrangement. An impulse test for a square electrode with extended conductors is carried out in condition of three current waveforms with different amplitude. Based on the electrical network model and iterative algorithm method, a calculation model is proposed to simulate the impulse characteristic of large-scale grounding grid considering soil ionization. The curve of impulse resistance against the current amplitude shows the soil ionization both from the simulation and test. Deviation between the simulation and test result is less than 15%.

• 한국태양에너지학회 논문집
• /
• 제33권4호
• /
• pp.39-45
• /
• 2013

This paper presents the estimation of minimum BESS capacity for regulating the output of wind farms considering power grid operating condition in Jeju Island. To analyze the characteristics of wind farm outputs with a BESS, the real data of wind farms, Sung-San, Sam-dal and Hang-Won wind farm, located in the eastern part of Jeju island is considered. The wind farms are connected to Sung-san substation to transfer the electric power to Jeju power grid. Consequently, at PCC (Point of Common Coupling), it can see a huge wind farm connected to the substation and thus it can be expected that the smoothing effect is affected by not only the different wind speeds for each area but also the different mechanical inertia of wind turbines. In this paper, two kinds of simulation have been carried out. One is to analyze the real data of wind farm outputs during a winter season, and the other is to connect a virtual BESS to eliminate the unintended generating power changes by the uncontrolled wind farm outputs as shown in the former data. In the conclusion, two kinds of simulation results show that BESS installed in the substation is more efficient than each wind farms with BESS, respectively.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2004년도 추계학술발표회 발표논문집
• /
• pp.841-842
• /
• 2004

• 한국산학기술학회논문지
• /
• 제20권10호
• /
• pp.18-25
• /
• 2019

최근, 도서지역의 신재생에너지전원 및 ESS의 도입이 확대되면서, 이산화탄소 배출의 저감을 위하여, 디젤발전기 대신 CVCF 인버터가 주 전원인 Micro-grid를 안정적으로 운용하는 방안들이 연구되고 있다. 그러나, CVCF 인버터 기반의 Micro-grid에서는 전체 부하보다 신재생에너지전원의 출력이 큰 경우에 에너지 Sinking(과도상태) 현상이 발생하게 된다. 이 때, CVCF 인버터용 배터리의 SOC 상태에 따라, 배터리 전압이 급격히 상승하여, 인버터의 과전압 보호동작에 의해 CVCF 인버터가 탈락되어 Micro-grid 전체 계통에 정전을 유발할 수 있다. 따라서, 본 논문에서는 CVCF 인버터를 기반으로 한 도서지역용 Micro-grid의 안정적인 운용을 위하여, 에너지 Sinking이 발생한 경우의 운용특성을 분석하고, CVCF 인버터가 에너지 Sinking 시에 탈락되는 것을 사전에 방지할 수 있는 Micro-grid의 과도상태 운용전략을 제안한다. 또한, CVCF 인버터, 태양광전원, 수용가부하로 구성된 30kW급 Micro-grid 시험장치를 구현하여, 실 계통에서의 에너지 Sinking에 의한 CVCF 인버터 기반 Micro-grid의 과도상태 시 운용특성을 제시한다. 한편, 30kW급 시험장치와 제안한 운용전략을 바탕으로 Micro-grid의 과도상태 운용특성을 분석한 결과, CVCF 인버터용 배터리의 전압과 SOC에 따라 인버터가 탈락하는 과도상태를 사전에 방지할 수 있어, 본 논문의 유용성을 확인하였다.

• 대한디지털의료영상학회논문지
• /
• 제9권2호
• /
• pp.23-30
• /
• 2007

This study attempts to propose an appropriate method of using digital medical imaging equipments, by studying the effects of automatic exposure control(AEC), grid ratio and the change of radiography distance on the patient dose and detertor acquisition dose during the procedure of acquiring image through a digital medical imaging detector. The change of dose following the change of grid ratio's exposure and radiography distance was measured, by using an abdominal phantom organized with tissue equivalent materials in an amorphous silicon thin film transistor detecter installed with AWC. The case to use grid ratio 12 : 1, focal distance 180cm to radiography distance 110cm in AEC, the patient dose increased rather when we used grid ration 10 : 1, focal distance 110cm. When AEC was not used,the dose necessary for image acquisition decreased as the grid ratio became higher and the distance became further. but detector acquisition dose was not reduced when in applied AEC. When purchasing digiral medical imaging equipments, optional items such as AEC and grid shall be accurately selected to satisfy the use of the equipments. Radiography error made by radiation technologist and unnenessary patient dose can be reduced by selecting equipments with a radiography distance marker equipment when it did not apply AEC. These equipments can also be helpful in maintaining high imaging quality, one of the merits of digital detectors.