• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.3D
• /
• pp.499-509
• /
• 2006

Precast concrete deck has many advantages comparing with the in-situ concrete deck, and has been successfully applied to replacement of the deteriorated decks and to the newly constructed highway bridges in domestic region. In order to apply the precast decks into the railway bridges, however, differences of the load characteristics between the highway and the railway should be properly taken into account including the train load, longitudinal force of the continuous welded rail, acceleration or braking force, temperature change and shrinkage. Proper level of the longitudinal prestress of the tendons that can ensure integrity of the transverse joints in the deck system is of a primary importance. To this aim, the longitudinal tensile stresses induced by the design loads are derived using three-dimensional finite element analyses for the frequently adopted PSC composite girder railway bridge. The effect of the temperature change is also investigated considering the design codes and theoretical equations in an in-depth manner. The estimated proper prestress level to counteract those tensile stresses is above 2.4 MPa, which is similar to the case of the highway bridges.

• The Journal of Engineering Geology
• /
• v.27 no.3
• /
• pp.233-244
• /
• 2017

We conducted hydraulic fracturing experiments on cement samples to investigate the dependency of fracture propagation on the viscosity of injection fluid and the in situ stress state. Ten cubic samples (20 cm side length) were produced using cement that was cured in water for more than one month. Samples were placed in a tri-axial compression apparatus with three independent principal stresses. An injection hole was drilled and the sample was hydraulically fractured under a constant injection rate. We measured injection pressures and acoustic emissions (AE) during the experiments, and investigated the fracture patterns produced by hydraulic fracturing. Breakdown pressures increased exponentially with increasing viscosity of the injection fluid. Fracture patterns were dependent on differential stress (i.e., the difference between the major and minor principal stresses). At low differential stress, multiple fractures oriented sub-parallel to the major principal stress axis propagated from the injection hole, and in some samples the fracture orientation changed during propagation. However, at high differential stress, a single fracture propagated parallel to the major principal stress axis. AE results show similar patterns. At low differential stress, AE source locations were more widespread than at high differential stress, consistent with the fracture pattern results. Our study suggests that hydraulic fracturing during shale gas extraction should be performed parallel to the orientation of minimum differential stress.

• Asian Pacific Journal of Cancer Prevention
• /
• v.14 no.9
• /
• pp.5007-5010
• /
• 2013

Heat shock proteins are molecular chaperones that may be constitutively present in cells protecting them from various stresses, such as extreme temperature, anoxia or chemical agents. Cervical cancer is the second most prevalent malignancy of women. In this study, we analyzed the expression of Hsp27 by immunohistochemistry in cervical intraepithelial lesions of Brazilian women, along with samples from non neoplasic lesions (NN). Cervical intraepithelial neoplasia I (CIN I), II (CIN II) and III (CIN III)/in situ carcinoma and squamous cell carcinoma (SCC) were included. Immunostaining was observed in 30 (100%) samples of NN, 46 (92%) in CIN I, 50 (100%) in CIN II, 52 (98.11%) in CIN III/CIS, and 46 (98.11%) in SCC. In group NN Hsp27 immunostaining was heterogeneous, more intense in basal and parabasal layers of the epithelium and less or absent in the intermediate and superficial layer. The majority of the samples of CIS and SCC presented strong staining in all epithelial layers. Metaplasic cells, when present, were strongly stained. In this study, Hsp27 protein was found to be commonly expressed in cervical epithelial cells.

• Proceedings of the Korean Society of Life Science Conference
• /
• 2005.04a
• /
• pp.23-36
• /
• 2005

Bax, a mammalian pro-apoptotic member of the Bcl-2 family, induces cell death when expressed In yeast. To investigate whether .Bax expression can induce cell death in plant, we produced transgenic Arabidopsis plants that contained murine Bax cDNA under control of a glucocorticoid-inducible promoter. Transgenic plants treated with dexamethasone, a strong synthetic glucocorticoid, induced Bax accumulation and cell death, suggesting that some elements of cell death mechanism by Bax may be conserved among various orgarusms. Therefore, we developed novel yeast genetic system, and cloned several Plant Bax Inhibitors (PBIs). Here, we report the function of two PBIs In detail. PBIl is ascorbate peroxidase (sAPX). Fluorescence method of dihydrorhodamine123 oxidation revealed that expression of Bax in yeast cells generated reactive oxygen species (ROS), and which was greatly reduced by co-expression with sAPX. These results suggest that sAPX inhibits the generation of ROS by Bax, which in turn suppresses Bax-induced cell death in yeast. PBI2 encodes nucleoside diphosphate kinase (NDPK). ROS stress strongly induces the expression of the NDPK2 gene in Arabidopsis thaliana (AtNDPK2). Transgenic plants overexpressing AtNDPK2 have lower lovels of ROS than wildtype plants. Mutants lacking AtNDPK2 had higher levels of ROS than wildtype. H$_{2O2}$ treatment induced the phosphorylation of two endogenous proteins whose molecular weights suggested they are AtMPK3 and AtMPK6. In the absence of H2O2 treatment, phosphorylation of these proteins was slightly elevated in plants overexpressing AtNDPK2 but markedly decreased In the AtNDPK2 deletion mutant. Yeast two-hybrid and in vitro protein pull-down assays revealed that AtNDPK2 specifically interacts with AtMPK3 and AtMPK6. Furthermore, AtNDPK2 also enhances the MBP phosphorylation activity of AtMPK3 i'n vitro. Finally, constitutive overexpression of AtNDPK2 in Arabidopsis plants conferred an enhanced tolerance to multiple environmental stresses that elicit ROS accumulation In situ. Thus, AtNDPK2 appears to play a novel regulatory role in H2O2-mediated MAPK signaling in plants.

• Geomechanics and Engineering
• /
• v.8 no.2
• /
• pp.187-220
• /
• 2015

Soil disturbance induced by installation of mandrel driven vertical drains decreases the in situ horizontal hydraulic conductivity of the soil in the vicinity of the drains, decelerating the consolidation rate. According to available literature, several different profiles for the hydraulic conductivity variation with the radial distance from the vertical drain, influencing the excess pore water pressure dissipation rate, have been identified. In addition, it is well known that the visco-plastic properties of the soil also influence the excess pore water pressure dissipation rate and consequently the settlement rate. In this study, a numerical solution adopting an elastic visco-plastic model with nonlinear creep function incorporated in the consolidation equations has been developed to investigate the effects of disturbed zone properties on the time dependent behaviour of soft soil deposits improved with vertical drains and preloading. The employed elastic visco-plastic model is based on the framework of the modified Cam-Clay model capturing soil creep during excess pore water pressure dissipation. Besides, nonlinear variations of creep coefficient with stress and time and permeability variations during the consolidation process are considered. The predicted results have been compared with V$\ddot{a}$sby test fill measurements. According to the results, different variations of the hydraulic conductivity profile in the disturbed zone result in varying excess pore water pressure dissipation rate and consequently varying the effective vertical stresses in the soil profile. Thus, the creep coefficient and the creep strain limit are notably influenced resulting in significant changes in the predicted settlement rate.

• International conference on construction engineering and project management
• /
• 2005.10a
• /
• pp.655-661
• /
• 2005

For a hydro power plant project, the headrace tunnel having a finished diameter of 3.3m was constructed in volcanic rocks with well-developed vertical joint and high groundwater table. The intake facility was located 20.3 km upstream of the powerhouse and headrace tunnel of 20 km in length and penstock of 440 m in height connected the intake and the powerhouse. The typical caldera lake, Lake Toba set the geology at the site; the caving of the ground caused tension cracks in the vertical direction to be developed and initial stresses at the ground to be released. High groundwater table(the maximum head of 20 bar) in the area of well-connected vertical joints delayed the progress of tunnel excavation severely due to the excessive inflow of groundwater. The excavation of tunnel was made using open-shield type TBM and mucking cars on the rail. High volume of water inflow raised the water level inside tunnel to 70 cm, 17% of tunnel diameter (3.9 m) and hindered the mucking of spoil under water. To improve the productivity, several adjustments such as modification of TBM and mucking cars and increase in the number of submersible pumps were made for the excavation of severe water inflow zone. Since the ground condition encountered during excavation turned out to be much worse, it was decided to adopt PC segment lining instead of RC lining. Besides, depending on the conditions of the water inflow, rock mass condition and internal water pressure, one of the invert PC segment lining with in-situ RC lining, RC lining and steel lining was applied to meet the site specific condition. With the adoption of PC segment lining, modification of TBM and other improvement, the excavation of the tunnel under severe groundwater condition was successfully completed.

• Journal of Plant Biotechnology
• /
• v.6 no.2
• /
• pp.77-85
• /
• 2004

Development of efficient plant regeneration and genetic transformation protocols (using the Particle Inflow micro-projectile Gun and the shoot-tips as target tissue) of Sorghum bicolor (L.) Moench in terms of expression of the reporter gene, $\beta$-glucuronidase(uidA) is reported here. Two Indian cultivars of sorghum were used in the study, viz. M-35-1 and CSV-15. Plant regeneration was achieved from one-week-old seedling shoot-tip explants via multiple-shoot-clumps and also somatic embryos. The multiple-shoot-clumps were produced on MS medium containing BA (0.5, 1.0 or 2.0 mg/$L^{-1}$), with biweekly subculture. Somatic embryos were directly produced on the enlarged dome shaped expansive structures that developed from shoot-tip explants (without any callus formation) when cultured on MS medium supplemented both with BA (0.5, 1.0 or 2.0 mg/$L^{-1}$) and 2,4-D (0.5 mg/$L^{-1}$). Whereas each multiple-shoot-clump was capable of regenerating more than 80 shoots via an intensive differentiation of both axillary and adventitious shoot buds, the somatic embryos were capable of 90% germination, plant conversion and regeneration. The regenerated shoots could be efficiently rooted on MS medium containing 1.0mg/$L^{-1}$ IBA and successfully transplanted to the glasshouse and grown to maturity with a survival rate of 92%. The plant regeneration efficiency of both the genotypes were similar. After the micro-projectile bombardment, expression of uidA gene was determined by scoring blue transformed cell sectors in the bombarded tissue by an in situ enzyme assay. The optimal conditions comprising a helium pressure of 2200 K Pa, the target distance of 11 cm with helium inlet fully opened and the use of osmoticum have been defined to aid our future strategies of genetic engineering in sorghum with genes for tolerance to biotic and abiotic stresses.

• Progress in Superconductivity and Cryogenics
• /
• v.21 no.1
• /
• pp.40-44
• /
• 2019

This study investigates mixtures of water and cryoprotectant agents (CPAs) to store high-grade cold energy. Although water is an ideal material for a cold thermal storage (CTS) due to its high specific heat, undesirable volume expansion may cause structural stresses during freezing. The volume expansion can be alleviated by adding the CPAs to water. However, the CPA aqueous solutions not only have different thermal properties but also transit to amorphous state different from pure water. Therefore, these characteristics should be considered when using them as material of the CTS. In experiments, glycerol and dimethyl sulfoxide (DMSO) are selected as the candidate CPA. The volume expansion of the solution is measured by an in-situ strain gauge in low temperature region. The specific heat capacity of the solution is also measured by differential scanning calorimetry (DSC). Both the amount of volume expansion and the specific heat capacity of the CPA aqueous solution decrease in the case of higher concentration of CPA. These characteristics should be contemplated to select optimal aqueous solution for CTS for liquid air energy storage system (LAES). The CPA solutions have advantages of having wide temperature range to utilize the latent heat of water and higher sensible heat of the CPA. The CPA solutions which can satisfy the allowable stress of the structure are determined. Consequently, among the CPA solutions investigated, DMSO 20% w/w solution is the most suitable for the CTS.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.4 no.3
• /
• pp.235-245
• /
• 2002

The purpose of this study is to figure out the tendency of tunnel convergence during excavation and to present a methodology for the prediction of a fault zone ahead of a tunnel face by analyzing three dimensional displacements in various ways. 3-D numerical analysis was performed to investigate changes of tunnel convergence vectors near a fault zone and to propose a flow chart for predicting fault zones. Results of the site investigation and results of trend line analysis of in-situ data were compared to verify the usefulness of a trend line analysis. It is concluded that the orientation of faults can be predicted by using stereonets and the direction of initial stresses can be predicted from the arm length of a displacement vector as a tunnel approaches fault zones. The results of the trend line analysis coincided with those of the site investigation, and a methodology for the prediction of a fault zone was proposed.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.2
• /
• pp.23-30
• /
• 1999

The relationships between morphological structures and residual stress behaviors of polyimide thin films depending on isomeric diamines were investigated. For this study, Poly(phenylene biphenyltetracarboximide) (BPDA-PDA) and poly(oxydiphenylene biphenyltetracarboximide) (BPDA-ODA) films were prepared from their isomeric diamines: 1,3-phenylene diamine (1,3-PDA) 1,4-phenylene diamine (1.4-PDA), 3,4'-oxydiphenylene diamine (3,4'-ODA), and 4,4'-oxydiphenylene diamine (4,4'-ODA), respectively. For those films, residual stresses were detected in-situ during thermal imidization of the isomeric polyimide as a function of processing temperature over the range of 25~$400^{\circ}C$ using. Thin Film Stress Analyzer (TFSA). In comparison, residual stress of BPDA-1.4PDA having better in-plain orientation and chain order was the lowest value of 7MPa whereas those of BPDA-1,3-PDA, BPDA-3,4'-ODA, and BPDA-4,4'-ODA were in the range of 40-50MPa. Conclusively, the effect of morphological nature (chain rigidity, chain order, orientation) and chain mobility relating to the g1ass transition behavior on the residual stress of isomeric polyimide thin films wart analyzed.