• Journal of the Korean Society of Clothing and Textiles
• /
• v.27 no.7
• /
• pp.843-850
• /
• 2003

Cu/PET film composites were prepared by electroless copper plating method. In order to improve adhesion between electroless plated Cu layer and polyester (PET) film, the effect of pretreatment conditions such as etching method, mixed catalyst composition were investigated. Chemical etching and plasma treatment increased surface roughness in decreasing order of Ar＞HCl＞O$_2$＞NH$_3$. However, adhesion of Cu layer on PET film increased in the following order: $O_2$＜Ar＜HCl＜NH$_3$. It indicated that appropriate surface roughness and introduction of affinitive functional group with Pd were key factors of improving adhesion of Cu layer. PET film was more finely etched by HCI tolution, resulting in an improvement in adhesion between Cu layer and PET film. Plasma treatment with NH$_3$produced nitrogen atoms on PET film, which enhances chemisorption of Pd$^{2+}$ on PET film, resulting in improved adhesion and shielding effectiveness of Cu layer deposited on the Pd catalyzed surface. Surface morphology of Cu plated PET film revealed that Pd/Sn colloidal particles became more evenly distributed in the smaller size by increasing the molar ratio of PdCl$_2$; SnCl$_2$from 1 : 4 to 1 : 16. With increasing the molar ratio of mixed catalyst, adhesion and shielding effectiveness of Cu plated PET film were increased.d.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.6
• /
• pp.1-7
• /
• 1993

After the 1%S-Al metal is deposited, a thin oxide is formed thereon. Then, a single charged Argon(Ar$^{+}$) is ion implanted into the oxide layer, thereby causing the metal grain in the upper surface of the metal layer to become amorphous. Consequently, the grain size will be reduced and the rough surface of the metal layer flattened. However, the remainder of the metal layer beneath the upper surface thereof will still exhibit large grain size and low resistance, because the Argon ion is only implanted to characterized by a dual-sized grain structure which served to reduce interlayer stress, thereby decreasing the rate of stress migration, and to lower the resistivity of the metal line, thereby enhancing the electromigration characteristic thereof. Experiments have shown that the metal line exhibits a metal migration rate which is approximately 700% less than the control group and a standard deviation which is approximately 200% less than these group.p.

• Journal of Technologic Dentistry
• /
• v.41 no.4
• /
• pp.279-285
• /
• 2019

Purpose: The dental CAD / CAM system has been popular with the development of the digital dental industry. Zirconia is a typical material in dental CAD / CAM systems. Zirconia crowns are classified into single layer and double layer. This study is about the double layer crown of zirconia. The surface roughness, bond strength and fracture patterns of the zirconia surface were observed. Methods: Zirconia blocks were cut using a low speed cutter. Sintered to form a plate shape (6mm × 6mm × 3mm). The prepared specimens were surface treated in four ways. Surface roughness and bond strength were measured. And the fracture pattern was observed. Results: Result of surface treatment of zirconia. The surface roughness test results were as ET 2.87 ㎛, ST 2.67 ㎛, LT 2.44 ㎛, AT 2.41 ㎛, CN 2.08 ㎛ order. Bond Strength results were as LT 25.09 MPa, AT 23.27 MPa, ST 21.27 MPa, ET 21.09 MPa, CN 16.12 MPa order. Fracture patterns showed cohesive failure of 25-50% of the bond area. Conclusion: Surface roughness, bond strength and fracture pattern of the zirconia surface were observed. Etching the surface treatment of zirconia materials has been shown to affect the surface roughness. Zirconia special binder treatment has been shown to affect the bond strength improvement.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.9
• /
• pp.818-824
• /
• 2006

The effects of high-temperature process required to fabricate the SiC devices on the surface morphology and the electrical characteristics were investigated for 4H-SiC Schottky diodes. The 4H-SiC diodes without a graphite cap layer as a protection layer showed catastrophic increase in an excess current at a forward bias and a leakage current at a reverse bias after high-temperature annealing process. Moreover it seemed to deviate from the conventional Schottky characteristics and to operate as an ohmic contact at the low bias regime. However, the 4H-SiC diodes with the graphite cap still exhibited their good electrical characteristics in spite of a slight increase in the leakage current. Therefore, we found that the graphite cap layer serves well as the protection layer of silicon carbide surface during high-temperature annealing. Based on a closer analysis on electric characteristics, a conductive surface transfiguration layer was suspected to form on the surface of diodes without the graphite cap layer during high-temperature annealing. After removing the surface transfiguration layer using ICP-RIE, Schottky diode without the graphite cap layer and having poor electrical characteristics showed a dramatic improvement in its characteristics including the ideality factor[${\eta}$] of 1.23, the schottky barrier height[${\Phi}$] of 1.39 eV, and the leakage current of $7.75\{times}10^{-8}\;A/cm^{2}$ at the reverse bias of -10 V.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.737-740
• /
• 2007

The buffer layer was spin-coated on the dielectric layer of OTFTs to introduce the hydrophobicity for enhancing the device performance. this functional layer contains the water-proof ingredient to reduce the surface energy and more importantly, does not harm the dielectric property of the dielectric layer. With the help of proposed hydrophobic layer, the transistor showed dramatic improvement at electrical performance which was almost 20 times higher mobility compared to the non-treated case. And on/off ratio was also guaranteed as $10^{5{\sim}6}$.

• Journal of the Korean Institute of Rural Architecture
• /
• v.23 no.4
• /
• pp.63-71
• /
• 2021

The purpose of this study was to investigate whether the standard models for rural housing and wooden housing model have performance for hygrothermal and to propose a way of improvement relevant to hygrothermal performance for those models. All of the models to be analyzed were found to have some parts that were absent of stability in terms of performance for hygrothermal. In the process of analyzing the causes and proposing improvement measures, the following conclusions were derived. Fist, The exterior surface of the structure should be composed of a structure with good moisture permeability, and for the interior surface, a variable vapor retarder paper should be applied in consideration of the reverse condensation phenomenon in summer. Second, in terms of performance for hygrothermal, applications of external insulation plaster finish to the exterior wall or of ventilation method using a rafter vent on the roof should be avoided. Third, a rain screen method with a ventilation layer should be applied to the exterior wall, and a method of constructing ventilation layer separated from the insulation layer with a vapor retarder paper should be applied to the roof. Fourth, the application of insulation materials having capillary action, such as wood fiber insulation board or cellulose insulation board, contributes to more stable performance for hygrothermal.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2013.05a
• /
• pp.97-97
• /
• 2013

We present a comprehensive study on the integration of h-BN with silicon MOSFET. Temperature dependent mobility modeling is used to discern the effects of top-gate dielectric on carrier transport and identify limiting factors of the system. The result indicates that coulomb scattering and surface roughness scattering are the dominant scattering mechanisms for silicon MOSFETs at relatively low temperature. Interposing a layer of h-BN between $SiO_2$ and Si effectively weakens coulomb scattering by separating carriers in the silicon inversion layer from the charged centers as 2-dimensional h-BN is relatively inert and is expected to be free of dangling bonds or surface charge traps owing to the strong, in-plane, ionic bonding of the planar hexagonal lattice structure, thus leading to a significant improvement in mobility relative to undecorated system. Furthermore, the atomically planar surface of h-BN also suppresses surface roughness scattering in this Si MOSFET system, resulting in a monotonously increasing mobility curve along with gate voltage, which is different from the traditional one with a extremum in a certain voltage. Alternatively, high-k dielectrics can lead to enhanced transport properties through dielectric screening. Modeling indicates that we can achieve even higher mobility by using h-BN decorated $HfO_2$ as gate dielectric in silicon MOSFETs instead of h-BN decorated $SiO_2$.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.2
• /
• pp.275-282
• /
• 2010

The improved properties of surface layer can be achieved by so-called "new salt bath nitriding(NSBN)", which has been developed by a domestic company. This process based upon modified traditional salt bath nitriding process, increased hardenability with minimum toughness deterioration. This process also offers not only less white layer surfaces but also more eco-friendly one. That is, NSBN is the new eco-friendly surface treatment technology removing harmful $CN^-$ and toxic gas. According to the research of applying NSBN to Cr-Mo-V steel which has been used in defense industry, showed the improved result of wear resistance and surface hardening than non-coated condition. In further, we expect NSBN to curtail expenses and productivity improvement applied to the various defense industry parts.

• Ocean and Polar Research
• /
• v.25 no.4
• /
• pp.459-468
• /
• 2003

Annual variation of water qualities in the Shihwa Lake were observed 18 times from June 1996 to October 2001. We studied at the station of the upper streams and near the water gate of lake. After the flow of the outer seawater through the water gate, the surface salinity in Shihwa Lake increased to the range of 25-30 psu in both stations after October 1998. Due to the declination of the salinity differences between the surface and the bottom water, the pycnocline in which had existed until 1997 has weakened, and made the water column mix vertically. This led to the improvement of anoxic/hypoxic environment at bottom waters after April 1998. However, despite the continuous flow of the outer seawater, the concentrations of chlorophyll-a at surface layer were varied from $2{\mu}g/l\;to\;60{\mu}g/l$, and these values indicated the eutrophication. The following organic matter load was greatly influencing the surface layer's COD concentration. During the rainy season, the salinity at the surface layer to the below 15 psu resulting in stratification between the surface and bottom layer. Organic matters that were provided from the surface layer to the bottom layer due to active primary production in the year exhausted dissolved oxygen at the bottom layer, and the bulks of organic matters at bottom gave rise to hypoxic or anoxic environment. It was observed that the enrichment of ammonia and phosphate were main factors to worsen the water quality of the Shihwa Lake. The results of examining the annual variations in Shiwha Lake through principal component analysis shown that water characteristics in the rainy season were similar with those before input of outer sea water.

• New & Renewable Energy
• /
• v.6 no.1
• /
• pp.46-52
• /
• 2010

Membrane electrode assemblies (MEAs) for proton exchange membrane fuel cells (PEMFCs) have been extensively studied to improve their initial performance as well as their durability and to facilitate the commercialization of fuel cell technology. To improve the MEA performance, particularly at low Pt loadings, many approaches have been made. In the present study, MEA performance improvement was performed by adding $TiO_2$ particles into the catalyst layer of MEA. Most of previous studies have focused on the MEA performance enhancement under low humidity conditions by adding metal oxides into the catalyst layer mainly due to the water keeping ability of those metal oxides particles such as $Al_2O_3$, $SiO_2$ and zeolites. However, this study mainly focused on the improvement of MEA performance under fully humidified normal conditions. In this study, the MEA was prepared by decal method aiming for a continuous MEA fabrication process. The decal process can make very thin and uniform catalyst layer on the surface of electrolyte membrane resulting in very low interfacial resistance between catalyst layer and the membrane surface and uniform electrode structure in the MEA. It was found that the addition of $TiO_2$ particles into the catalyst layer made by decal method can minimize water flooding in the catalyst layer, resulting in the improvement of MEA performance.