• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.3
• /
• pp.52-58
• /
• 1999

In this study, the growth-strain method was used for shape optimization. The adequate value of growth ratio in the method was used the value obtained by volume control. And the linear PID control theory was applied to control internal stresses by stresses required by a designer. The effect of the values of $K_{P}$, $K_{I}$, and $K_{D}$ was investigated and the adequate values of $K_{P}$, $K_{I}$, and $K_{D}$ were determined empirically. Finally, a shape optimal design system was built up by the improved the growth-strain method with a commercial software I-DEAS. The effectiveness and practicality of the developed shape optimal design system was verified by some examples.les.les.les.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.735-738
• /
• 1997

The aerodynamic charateristics of high speed train can be improved by fore-body design. In this paper, the design a fore-body shape which has optimal aerodynamic charateristics, 6 models of fore-body shape are proposed and the change of aerodynamic characteristics is studied through calculations of flow field around high speed train fro each fore-body shape. The flow field around high speed trains are calculated using Navier-Stokes equation. The variational trends of aerodynamic characteristics are studied from the result of flow calculation around high speed trains for 6 fore-body shapes.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.443-446
• /
• 2003

The vibration mode shape changed by the phase angle that can be controlled by phase-shifting ESPI system is discussed. For the phase-shifting ESPI experiment the stroboscopic illumination by using AOM(Acousto-Optic Modulator) is needed, and the initial phase angle can be adjusted by the program. The vibration mode shape is changed when the initial phase angle is changed. We examined the vibration mode shape change due to the initial phase angle change at each resonance frequency. Through this study, we found that in the vibration testing using phase-shilling ESPI the vibration mode shape is improved in the quality by adjusting exact phase angle and the error of the quantitative vibration analysis can be reduced.

• Structural Engineering and Mechanics
• /
• v.12 no.5
• /
• pp.491-506
• /
• 2001

In this paper, a new three-dimensional piezoelectric thin shell element containing an integrated distributed piezoelectric sensor and actuator is proposed. The distributed piezoelectric sensor layer monitors the structural shape deformation due to the direct effect and the distributed actuator layer suppresses the deflection via the converse piezoelectric effect. A finite element formulation is presented for static response of laminated shell with piezoelectric sensors/actuators. An eight-node and forty-DOF shell element is built. The performance of the shell elements is improved by reduced integration technique. The static shape control of structure is derived. The shell element is verified by calculating piezoelectric polymeric PVDF bimorph beam. The results agreed with those obtained by theoretical analysis, Tzou and Tseng (1990) and Hwang and Park (1993) fairly well. At last, the static shape control of a paraboloidal antenna is presented.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.2
• /
• pp.53-59
• /
• 2005

In this paper, optimum shape design of permanent magnet in slotted type Permanent Magnet Linear Synchronous Motor(PMLSM) is progressed for minimization of detent force owing to structure of slot-teeth and thrust ripple by harmonic magnetic flux of permanent magnet. In order to reduce remodeling time as changing design parameter for Permanent Magnet shape optimization, the moving model node technique was applied. The characteristics of thrust and detent force computed by finite element analysis are acquired equal effect both skewed basic model and optimum model which is optimization of permanent magnet shape. In addition to, thrust per unit volume is improved 4.l2[%] in optimum model.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1998.03a
• /
• pp.185-195
• /
• 1998

A new blank design method is proposed to predict the optimum initial blank shape in the sheet metal forming process. The rollback method for blank shape design takes the difference between final deformed shape and target contour shape into account. Based on the method, a computer program composed of blank design module, FE-analysis program and mesh generation module is developed. The rollback method is applied to square cup drawing process with the flange of unifiorm size around its periphery to confirm its validity. The optimum initial blank shape is obtained from an arbitrary square blank after three modifications. Good agreements are recognized between the numerical results and the published results for initial blank shape and thickness strain distribution. The optimum blank shape for two parts of automobile sub-frame is designed. The thickness distribution and the level of punch load is improved. Also, the method is applied to design the weld line in the tailor-welded blank. It is concluded that the rollback method is an effective and convenient method for an optimum blank shape design.

• Journal of Ocean Engineering and Technology
• /
• v.31 no.6
• /
• pp.425-430
• /
• 2017

In order to reduce the cost of corrections and time needed for the block assembly process, the reverse setting method is applied for a back-heated block to neutralize deck deformation. The proper reverse setting shape for a back-heated block to correct deformation improved the deck flatness, but an excessive amount of reverse setting could inversely affect the flatness of the block. A prediction method was developed for the proper reverse setting shape using a back-heated block, considering the complex geometry of blocks, thickness of the deck plate, and thermal loading conditions such as welding and back-heating. The prediction method was developed by combining the re-meshing technique and inherent strain-based deformation analysis using the finite element method. Because the flatness deviation was decreased until the lower critical point and thereafter it tended to increase again, the optimum value for which the flatness was the best case was selected by repeatedly calculating the predefined reverse setting values. Based on this analysis and the study of the back-heating deformation of large assembly blocks, including the reverse setting shape, the mechanism for selecting the optimum reverse setting value was identified. The developed method was applied to the actual blocks of a ship, and it was confirmed that the flatness of the block was improved. It is concluded that the developed prediction method can be used to predict the optimum reverse setting shape value of a ship's block, which will reduce the cost of corrections in the construction stage.

• Nuclear Engineering and Technology
• /
• v.53 no.4
• /
• pp.1189-1198
• /
• 2021

When performing remote tasks using robots in nuclear power plants, a 3D shape measurement system is advantageous in improving the efficiency of remote operations by easily identifying the current state of the target object for example, size, shape, and distance information. Nuclear power plants have high-radiation and underwater environments therefore the electronic parts that comprise 3D shape measurement systems are prone to degradation and thus cannot be used for a long period of time. Also, given the refraction caused by a medium change in the underwater environment, optical design constraints and calibration methods for them are required. The present study proposed a method for developing an underwater 3D shape measurement system with improved radiation tolerance, which is composed of commercial electric parts and a stereo camera while being capable of easily and readily correcting underwater refraction. In an effort to improve its radiation tolerance, the number of parts that are exposed to a radiation environment was minimized to include only necessary components, such as a line beam laser, a motor to rotate the line beam laser, and a stereo camera. Given that a signal processing circuit and control circuit of the camera is susceptible to radiation, an image sensor and lens of the camera were separated from its main body to improve radiation tolerance. The prototype developed in the present study was made of commercial electric parts, and thus it was possible to improve the overall radiation tolerance at a relatively low cost. Also, it was easy to manufacture because there are few constraints for optical design.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.10a
• /
• pp.857-862
• /
• 2007

In this paper, we studied about the antenna designed by heart-shape beam pattern for 4G mobile communication applications. The proposed whole size of structure was identical if it compare with the basis structure. But size of the patch was improved a little(upaward 1.3). The impedance bandwidth was improved about 258% which compares with the basis structure. And the structure could get very good characteristic applicatory to IMT-Advanced. Impedance bandwidth of antenna was about 22%(870MHz). The gain of above 8.7dBi was achieved extended IMT-Advanced all frequency band.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.705-709
• /
• 2002

The spacer grids in nuclear fuel assembly locate and align the fuel rods with respect to each other. They provide axial and lateral restraint against an excessive rod motion mainly caused by coolant flow. It is understood that each rod Is supported by multiple spacer grid. In such a case, it is important to determine spacer grid span so as to avoid resonance between the natural frequency of the fuel rods and excitation frequency. Actually dynamic characteristics of the fuel rods can be improved by assigning adequate spacer grid locations. When a dynamic performance of the structure is to be improved, design sensitivity analysis plays an important role as like many structural redesign problems. In this work, a shape design concept, different from conventional design, was applied to the problem. According to the theory shape can be a design parameter and optimal shape design can be found. This study concentrates on eigenvalue design sensitivity of the fuel rod supported by multiple spacer grids to determine optimal spacer grids positions.